Tail lights
Assembly overview - Tail lights body

- Left tail light -MX3- or right tail light -MX4- in the quarter panel
- Remove and install
- Tail light bulb holder in the quarter panel
- Remove and install
- Mounting nut
- Tightening torque: Screw on by hand until it stops (max. 2 N·m)
- Left brake and tail light bulb -M21- or right brake and tail light bulb -M22-
- Bulb 12V, P21/4W
- Left rear turn signal bulb -M6- or right rear turn signal bulb -M8-
- Bulb 12V, RY10W
- Left tail light bulb -M4- or right tail light bulb -M2-
- Bulb 12V, P21/4W
- Left reversing light bulb -M16- or right reversing light bulb -M17-
- Bulb 12V, R10W
- Left rear fog light bulb -L46- or right rear fog light bulb -L47-
- The rear fog light bulb also performs the tail light function with its 4-watt filament.
- Bulb 12V, P21/4W
Removing and installing bulb holder
Note
The removal and installation described is for the left side. Removal and installation on the right side is carried out in the same way.
Removing
- Switch off ignition and all electrical consumers and remove the ignition key.
- Remove the tail light from the quarter panel.
- Press the latches -arrows- outward and remove the bulb holder -1- from the tail light housing.
Installing
Installation is carried out in the reverse order, observing the following:
Note
When installing the bulb holder, make sure that all latches engage audibly.

Removing and installing tail light bulb -M2-/-M4-
Note
The removal and installation described is for the left side. Removal and installation on the right side is carried out in the same way.
Removing
- Switch off ignition and all electrical consumers and remove the ignition key.
- Remove the tail light bulb holder from the quarter panel.
- Press the tail light bulb -2- into the socket, turn it to the left and pull it upward out of the bulb holder -6-.
Tail light bulb: Bulb 12V, P21/4W
Installing
Install in reverse order.

Removing and installing tail light
Note
The removal and installation described is for the left side. Removal and installation on the right side is carried out in the same way.
Removing
- Switch off ignition and all electrical consumers and remove the ignition key.
- Remove the service flap -1- from the side panel trim in the luggage compartment.

- Remove the fastening nut -1- and take the tail light out to the rear through the body cutout in the quarter panel, taking the connected wiring lengths into account.

- Unlock the connector -arrow- and pull it off, then remove the tail light.
Installing
Installation is carried out in the reverse order, observing the following:
Caution!
Risk of damaging the wiring.
The wiring harness to the tail light can be pinched during installation.
After plugging in the electrical connector, route the wiring harness inward through the body cutout without interference.
- Screw in the fastening nut by hand until it stops.
- After installation, check the gaps to the body and the functions of the tail light.
Tightening torques
- "Assembly overview - Tail lights body"

Removing and installing rear fog light bulb -L46-/-L47-
Note
The removal and installation described is for the left side. Removal and installation on the right side is carried out in the same way.
Removing
- Switch off ignition and all electrical consumers and remove the ignition key.
- Remove the tail light bulb holder from the quarter panel.
- Press the rear fog light bulb -3- into the socket, turn it to the left and pull it upward out of the bulb holder -6-.
Rear fog light bulb: Bulb 12V, P21/4W
Installing
Install in reverse order.

Removing and installing brake and tail light bulb -M21-/-M22-
Note
The removal and installation described is for the left side. Removal and installation on the right side is carried out in the same way.
Removing
- Switch off ignition and all electrical consumers and remove the ignition key.
- Remove the tail light bulb holder from the quarter panel.
- Press the brake and tail light bulb -1- into the socket, turn it to the left and pull it upward out of the bulb holder -6-.
Brake and tail light bulb: Bulb 12V, P21/4W
Installing
Install in reverse order.

Removing and installing reversing light bulb
Note
The removal and installation described is for the left side. Removal and installation on the right side is carried out in the same way.
Removing
- Switch off ignition and all electrical consumers and remove the ignition key.
- Remove the tail light bulb holder from the quarter panel.
- Press the reversing light bulb -4- into the socket, turn it to the left and pull it upward out of the bulb holder -6-.
Reversing light bulb: Bulb 12V, R10W
Installing
Install in reverse order.

Removing and installing turn signal bulb
Note
The removal and installation described is for the left side. Removal and installation on the right side is carried out in the same way.
Removing
- Switch off ignition and all electrical consumers and remove the ignition key.
- Remove the tail light bulb holder from the quarter panel.
- Press the turn signal bulb -5- into the socket, turn it to the left and pull it upward out of the bulb holder -6-.
Turn signal bulb: Bulb 12V, RY10W
Installing
Install in reverse order.
