Maintenance
Chassis
In this manual: Maintenance
37steps
~222min
4/5difficulty
Done 0 of 37
Contents:
Brake Fluid Repair procedures ➤
Brake Lines, Hoses and Connections Repair procedures
Inspection
Visually check for proper installation, chafing, cracks, deterioration and any leakage. Replace any deteriorated or damaged parts immediately.Disc Brakes and Pads Repair procedures
On Vehicle inspection
Disc cleaning before inspection The rust generated on brake discs of long-term non-operating vehicles is naturally removed under normal driving conditions. However, it can affect the thickness and runout measurements, so for accurate measurements, remove them according to the procedure below.- Check the brake disc for rust.
- Spray the cleaning solution on rusted surface of disc.
Cleaning Solution : Cleaning solution : Water-Detergent [Water : 0.08 gal (300 ml) Detergent : 0.004 gal (15 ml)]
Do not use lubricating, oil-based cleaning agents (wax, rust inhibitors). Poor braking performance and risk of fire due to pad friction can occur during braking. - Turn the vehicle on, and then pull the RH paddle shift (A) to enter the regenerative braking mode '0'.
The rust of the brake disc can not be removed when regenerative braking mode in 1 or more. - Drive the vehicle up to 30 mph and depress the brake up to stop for complete repeat more than 5 cycles.
- Clean the brake disc with clean water.
- Check the brake disc for rust.
- If rust is not removed, repeat the above procedure again.
- Remove the front wheel and tires. (Refer to Suspension System - "Wheel")
- Check the brake disc for damage.
- Measure the brake disc thickness (A) and run-out using the micro meter and dial gauge at least 24 locations on the same column along the lines shown in the figure below.
Front brake disc thickness (A) 17" Disc standard : 30 mm (1.18 in.) 17" Disc service limit : 28 mm (1.10 in.) The difference between each measured thickness less than 0.015 mm (Column and Radial direction) - If the thickness difference between each measuring part is greater than standard, resurface or replace the brake disc.
- Resurface the brake disc according to the method of using the equipment in possession.
- If the brake disc is less than or equal to the limit, replace the brake disc with a new one.
- Install the front wheel and tires. (Refer to Suspension System - "Wheel")
- Remove the rear wheel and tires. (Refer to Suspension System - "Wheel")
- Check the brake disc for damage.
- Measure the brake disc thickness (A) and run-out using the micro meter and dial gauge at least 24 locations on the same column along the lines shown in the figure below.
Rear Brack Disc Thickness (A) 17" Disc standard : 12 mm (0.47 in.) 17" Disc limit : 10 mm (0.40 in.) The difference between each measured thickness less than 0.015 mm (Column and Radial direction) - If the thickness difference between each measuring part is greater than standard, resurface or replace the brake disc.
- Resurface the brake disc according to the method of using the equipment in possession.
- If the brake disc is less than or equal to the limit, replace the brake disc with a new one.
- Install the rear wheel and tires. (Refer to Suspension System - "Wheel")
- Remove the front wheel and tires. (Refer to Suspension System - "Wheel")
- Install the dial gauge perpendicular to the brake disc's external diameter of 10 mm (0.40 in.) and rotate the disc to measure the run-out.
Brake Disc Runout : Service limit : less than 0.050 mm (0.0019 in.)
- If the brake disc run-out exceeds the limit, resurface or replace the brake disc.
- Resurface the brake disc according to the method of using the equipment in possession.
- If the brake disc is less than or equal to the limit, replace the brake disc with a new one.
- Install the front wheel and tires. (Refer to Suspension System - "Wheel")
- Remove the rear wheel and tires. (Refer to Suspension System - "Wheel")
- Install the dial gauge perpendicular to the brake disc's external diameter of 10 mm (0.40 in.) and rotate the disc to measure the run-out.
Brake Disc Runout Service limit : 0.055 mm (0.002 in.) or less.
- If the brake disc run-out exceeds the limit, resurface or replace the brake disc.
- Resurface the brake disc according to the method of using the equipment in possession.
- If the brake disc is less than or equal to the limit, replace the brake disc with a new one.
- Install the rear wheel and tires. (Refer to Suspension System - "Wheel")
- Check brake pad thickness (A). If the thickness is thinner than the limit, replace the brake pads.
Front brake pad thickness Standard : 11.0 mm (0.433 in.) Service limit : 3.0 mm (0.118 in.)
Rear brake disc pad thickness Standard : 10.0 mm (0.393 in.) Service Limit : 2.0 mm (0.078 in.) - Check that grease is applied to sliding contact points and check the pad and backing metal for damage.
Drive Shafts and Boots Repair procedures. Steering Gear Rack, Linkage and Boots Repair procedures
Drive Shafts and Boots Repair procedures
Inspection
- Check the drive shaft boots for loose clamps, cracks, grease leaks, kinks or damage. [Front - 4WD only] [Rear]
Steering Gear Rack, Linkage and Boots Repair procedures
Inspection
Steering Wheel Play Inspection- Align the steering wheel straight.
- Mark the steering wheel center (A) using masking tape or equivalent.
- Turn the steering wheel until the wheel is moved while MDPS power is 'ON', then measure the distance the steering wheel has rotated.
Standard value : 0 - 30 mm (0 - 1.1811 in.) or less
- If the steering wheel play exceeds standard value, inspect the steering column, shaft, and linkages.
- Place the vehicle on the level surface.
- Measure the power when the steering wheel starts to move using a spring scale while MDPS power is 'ON'.
Standard value : 29.4 N (3.0 kgf, 6.6 lb·ft) MAX.
- If the measured value exceeds standard value, inspect the steering gear box or MDPS system.
Suspension Mounting Bolts Repair procedures. Tire (pressure & tread wear) Repair procedures
Suspension Mounting Bolts Repair procedures
Inspection
- Visually check the loose mount bolt.
Tire (pressure & tread wear) Repair procedures
Inspection
- Check the tire pressure.
Tire Front Rear 235/55 R19 250 - 255 kPa (36 - 37 psi) 255/45 R20 - Check the tire tread wear. (Refer to Suspension System - "Tire")
- Check if the wear of tire tread is uneven. (Refer to Suspension System - "Alignment")
Was this page helpful?