Restraint
In this manual: Restraint
32steps
~192min
4/5difficulty
Done 0 of 32
Contents:
Single-Use Parts
Single-Use Parts
Non-reusable parts (Single-Use Parts) Workshop manual provides “Components and Components Location” which can be used to identify “Non-reusable parts”. When repairing a vehicle, Non-reusable parts such as fasteners, gaskets, washers, clips and garnishes must be replaced. Kia Non-reusable parts are designed to be installed only once. Before working on a vehicle, check “Components and Components Location” to find the non-reusable parts in a system. ※ Symbol of Non-reusable parts| Symbol | Meaning |
| Do not reuse the part. Replace with a new one. |
※ Example of “Components and Components Location”
High Voltage System General Safety Information and Caution ➤
High Voltage Shut-off Procedures
High Voltage Shut-off Procedures
High Voltage Shut-off Procedures
|
| High Voltage Component : Battery System Assembly (BSA), motor assembly, inverter assembly, high voltage junction box, power cable, etc. |
- Check the Battery Management Unit (BMU) weld flag with the KDS. (Data Analysis → Battery Management System (BMS) → BMU Weld Flag)
Specified value : NO
Refer to the KDS screen for operating conditions and details. - Open the front trunk (A).
- Open the low voltage (12 V) battery service cover (A).
- Turn the POWER OFF, separate the low voltage (12 V) battery ( - ) terminal (A).
Tightening torque : 7.8 - 9,8 N·m
- Disconnect the service interlock connector (A).
- Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
- When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
The service interlock connector cannot be completely removed. - Remove the front under cover. (Refer to Motor and Reduction Gear System - "Front Under Cover")
- Remove the high voltage battery cover (A).
Tightening torque : 7.8 - 11,8 N·m
- Disconnect the front high voltage junction box power cable (A).
How to disconnect the connector - Release the locking clip (A) by pulling it.
- Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).
- Remove the center floor rear under cover. (Refer to Motor and Reduction Gear System - "Rear Under Cover")
- Disconnect the Integrated Charge Control Unit (ICCU) connector (A).
How to disconnect the connector - Release the locking clip (A) by pulling it.
- Disconnect the connector while pressing the locking clip (B).
- Disconnect the rear high voltage junction box power cable (A).
How to disconnect the connector - Release the locking clip (A) by pulling it.
- Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).
- Measure the voltage between the high voltage power connector and high voltage battery terminal to check whether the high voltage is shut-off.
30 V or less : Normal cut off high voltage circuit Above 30 V : Fault on high voltage circuit
- Measure the voltage between the high voltage power connector positive ( + ) terminal and negative ( - ) terminal.
- Measure the voltage between the high voltage battery positive ( + ) and negative ( - ) terminal.
- Measure the voltage between the high voltage battery positive ( + ) terminal and ground.
- Measure the voltage between the high voltage battery negative ( - ) terminal and ground.
- Measure the voltage between the rear high voltage battery positive ( + ) and negative ( - ) terminal.
- Measure the voltage between the rear high voltage battery positive ( + ) terminal and ground.
- Measure the voltage between the rear high voltage battery negative ( - ) terminal and ground.
- Check for insulation breakdown via KDS and physical leakage current before working on EV.
- Remove the main fuse if insulation breakdown or leakage current is suspected. (Remove the main fuse even when DTC CODE ON such as PRA malfunction) (Refer to High Voltage Battery Control System - "Main Fuse") ※ If there is no insulation breakdown or leakage current and it is normal, work without removing the main fuse.
Specification
Tightening Torque
Tightening Torque
Airbag Module Curtain Airbag (CAB)| Item | N·m | kgf·m | lb·ft | lb·in |
| Curtain Airbag (CAB) bolt | 7.8 - 11.8 | 0.8 - 1.2 | 5.8 - 8.7 | - |
| Curtain Airbag (CAB) nut | 3.9 - 5.9 | 0.4 - 0.6 | 2.9 - 4.3 | 34.7 - 52.1 |
Passenger Airbag (PAB)
| Item | N·m | kgf·m | lb·ft | lb·in |
| Passenger Airbag (PAB) bolt | 3.9 - 5.9 | 0.4 - 0.6 | 2.9 - 4.3 | 34.7 - 52.1 |
Side Airbag (SAB)
| Item | N·m | kgf·m | lb·ft | lb·in |
| Side Airbag (SAB) nut | 5.9 - 7.8 | 0.6 - 0.8 | 4.3 - 5.8 | 52.1 - 69.4 |
Seat Belt System Height Adjust
| Item | N·m | kgf·m | lb·ft | lb·in |
| Front seat belt upper anchor bolt | 39.2 - 53.9 | 4.0 - 5.5 | 28.9 - 39.8 | - |
| Height adjuster bolt | 39.2 - 53.9 | 4.0 - 5.5 | 28.9 - 39.8 | - |
Seat Belt Pretensioner (BPT)
| Item | N·m | kgf·m | lb·ft | lb·in |
| Seat Belt Pretensioner (BPT) bolt | 44.1 - 54.9 | 4.5 - 5.6 | 32.5 - 40.5 | - |
Seat Belt Reminder
| Item | N·m | kgf·m | lb·ft | lb·in |
| Seat belt buckle bolt and nut | 44.1 - 53.9 | 4.5 - 5.5 | 32.5 - 39.8 | - |
SRSCM Acceleration type Side Impact Sensor (A-SIS)
| Item | N·m | kgf·m | lb·ft | lb·in |
| Acceleration type Side Impact Sensor (A-SIS) bolt | 7.5 - 9.1 | 0.76 - 0.93 | 5.5 - 6.7 | - |
Airbag Control Unit (ACU)
| Item | N·m | kgf·m | lb·ft | lb·in |
| Airbag Control Unit (ACU) nut | 7.7 - 9.5 | 0.79 - 0.97 | 5.7 - 7.0 | - |
Front Impact Sensor (FIS)
| Item | N·m | kgf·m | lb·ft | lb·in |
| Front Impact Sensor (FIS) nut | 7.5 - 9.1 | 0.76 - 0.93 | 5.5 - 6.7 | - |
Pressure type Side Impact Sensor (P-SIS)
| Item | N·m | kgf·m | lb·ft | lb·in |
| Pressure type Side Impact Sensor (P-SIS) screw | 2.0 - 3.0 | 0.20 - 0.31 | 1.4 - 2.2 | 17.4 - 26.9 |
Special Service Tools
Special Service Tool
| Tool Name / Number | Illustration | Description |
| Deployment tool 0957A - 34100A |
Use when deploying airbag module | |
| Deployment adapter 0K57A - 3U100A |
Use when deploying DAB, PAB, CAB modules and BPT Used with the airbag deployment tool (9057A - 34100A) |
|
| Deployment adapter 0957A - 2W100 |
Used when deploying the SAB module Used with the airbag deployment tool (9057A - 34100A) |
|
| Dummy 0957A - 38200 |
Use to check the resistance of the airbag module | |
| Dummy adapter 0957A - 2W200 |
Use to check the resistance of SAB and KAB modules Used with 0957A - 38200 |
|
| Dummy adapter 0957A - 2G000 |
Use to check resistance of DAB, PAB, CAB modules and BPT Used with 0957A - 38200 |
|
| Deployment adapter 0957A - 3F100 |
Use when deploying KAB modules Use with 0957A - 34100A |
|
| Dummy adapter 0957A - 3F000 |
Use to check KAB module resistance Use with 0957A - 38200 |
|
General Safety Information and Caution
Precautions when repairing the airbag system
When repairing the SRS, pay attention to the following items.| If the items below are not observed, there is a possibility of serious injury due to unexpected airbag deployment, and the airbag may not operate. |
- After disconnecting the ( - ) terminal of the auxiliary 12 V battery in the POWER OFF state, wait at least 3 minutes and 30 seconds before starting related work. (Backup power is valid for about 150ms)
- Failure symptoms of the airbag system are difficult to identify. When troubleshooting, the DTC provides the most important information.
- When repairing an airbag system fault, always inspect the DTC before removing the battery.
- Do not measure the resistance of the airbag squib connector. (It is very dangerous because the airbag can be activated.)
Squib : It is an ignition device installed in the inflator of the electric airbag module. - Be careful not to damage the airbag module by oil, grease, cleaner and water.
- Do not use airbag components from other vehicles.
- When replacing components, replace them with new ones.
- Do not disassemble or repair to reuse for all airbag system components.
- When installing the airbag system, be careful not to impact around the airbag control unit and impact sensor. The airbag may be suddenly deployed, which may cause damage and injury.
- If the airbag module is dropped or other defects such as cracks, dents on the case, the bracket and the connector are occurred, replace them with new ones.
- After completing the SRS repair, check the warning lamp and delete the DTC.
The operation of the airbag warning light may be blocked by other circuit faults. Therefore, when the airbag warning light turns on, the DTC is deleted by using the KDS. - After completing the repair and inspection of the SRS, be sure to initialize the system. (Keep POWER ON for more than 7 seconds → Keep POWER OFF for more than 3 minutes and 30 seconds → Keep POWER ON for more than 7 seconds)
- Do not disassemble the airbag.
- The deployed airbags cannot be reused.
- Be sure to observe the following precautions when storing the airbag module.
- Store the airbag module with the top side of the cover facing upward.
- The double locking connector lever must be locked, and positioned so that the connector is not damaged.
- Be careful not to damage the airbag module by oil, grease, cleaner and water.
- Store in a place where the ambient temperature is below 60 °C, humidity is not high, and there is no electrical noise.
- Follow the disposal procedure for the damaged airbag modules. (Refer to Airbag Module - "The Airbag Module Disposal Procedure")
- Never reconnect or repair the damaged airbag wiring. If the airbag wiring is damaged, replace the harness.
- Make sure the wiring is not interfered with other components.
- Make sure that there are no foreign substances on the connector surface of the airbag module . Poor grounding can cause problems which are difficult to diagnose.
- When using the tester, insert the tester probe into the connector wire side. Do not insert the tester probe into the terminal side of the connector.
- Use a U-shaped probe and do not forcefully insert the probe.
- To disconnect the connector, remove the connector by holding the connector and pulling the spring loaded sleeve (A) and slider (B) from the opposite side. Be careful to pull the sleeve, not the connector.
- Hold both connectors and push firmly until the protrusion (C) of the connector on the sleeve side clicks into place.
Description and Operation
Description
- The airbag system is a supplemental restraint system to protect the driver and passengers from injuries by operating the airbags and seat belt pretensioner installed on the driver's and front passenger's seats in the event of a vehicle collision.
- The airbag system is configured as follows.
Name Abbreviation Airbag and seat belt warning light - Airbag Control Unit ACU Clock spring - Curtain Airbag CAB Driver Airbag DAB Front Impact Sensor FIS Knee Airbag KAB Passenger Airbag PAB Seat Belt Pretensioner BPT Side Airbag SAB Side Impact Sensor Acceleration type Front A-FSIS Acceleration type Rear A-RSIS Pressure type P-SIS
Airbag Warning Light
The airbag control unit turns on the airbag warning light by detecting whether there is an abnormality in the airbag system when the power is applied.- When the airbag system is normal, the airbag warning light turns on for 3 to 6 seconds and turns off.
- If there is a problem with the airbag system, the warning lamp will be on for 3 to 6 seconds, then go off for 1 second, then come back on and stay on.
- When in the variant coding mode.
- When POWER ON, the airbag warning light turns on for 3 seconds.
- The airbag warning lamp blinks at 1 second intervals until the variant coding is normally completed.
- When variant coding is normally completed, the airbag warning lamp turns on for 6 seconds and then turns off.
- When variant coding is not normally completed, the airbag warning lamp continues to blink at 1 second intervals.
- If there is a failure of the airbag system or an internal failure of the airbag system control module, variant coding should be re-performed after confirming the cause of failure and completing the action using the KDS.
- In the following cases, the airbag warning light continues to illuminate.
- If there is a failure of the airbag system or an internal failure of the airbag control unit.
- If there is a Diagnostic Trouble Code (DTC).
- If a failure occurs in which the airbag control module cannot operate, the operation of the airbag warning lamp cannot be controlled normally.
Repair Procedures
Replacement of components after deploying the airbag system
| Before the work related to the airbag, Check the Diagnosis Trouble Code (DTC) with the KDS. |
- When the airbags deployed after a collision, replace the following items.
- Airbag Control Unit (ACU)
- Replace the clock spring if there is any problem after checking the clock spring for damage when the driver airbag is deployed.
- Damaged impact sensor
- Airbag wiring harness
- Check that the airbag system operates normally after repairing the vehicle.
When POWER ON the airbag warning light should turn off after turning on for 3 - 6 seconds.
Airbag Module ➤
Seat Belt System ➤
SRSCM ➤
Was this page helpful?