Suspension System

12steps
~72min
3/5difficulty
010203040509.87N·mlb·ft
Tightening torque found on this page
Done 0 of 12

Contents:

Single-Use Parts

Single-Use Parts

Non-reusable parts (Single-Use Parts) Workshop manual provides “Components and Components Location” which can be used to identify “Non-reusable parts”. When repairing a vehicle, Non-reusable parts such as fasteners, gaskets, washers, clips and garnishes must be replaced. Kia Non-reusable parts are designed to be installed only once. Before working on a vehicle, check “Components and Components Location” to find the non-reusable parts in a system. ※ Symbol of Non-reusable parts
Symbol Meaning
Do not reuse the part. Replace with a new one.

※ Example of “Components and Components Location”

High Voltage System General Safety Information and Caution ➤

High Voltage Shut-off Procedures

High Voltage Shut-off Procedures

High Voltage Shut-off Procedures

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
High Voltage Component : Battery System Assembly (BSA), motor assembly, inverter assembly, high voltage junction box, power cable, etc.
  1. Check the Battery Management Unit (BMU) weld flag with the KDS. (Data Analysis → Battery Management System (BMS) → BMU Weld Flag)

    Specified value : NO

    Refer to the KDS screen for operating conditions and details.
  2. Open the front trunk (A).
  3. Open the low voltage (12 V) battery service cover (A).
  4. Turn the POWER OFF, separate the low voltage (12 V) battery ( - ) terminal (A).

    Tightening torque : 7.8 - 9,8 N·m

  5. Disconnect the service interlock connector (A).
    • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
    • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
    The service interlock connector cannot be completely removed.
  6. Remove the front under cover. (Refer to Motor and Reduction Gear System - "Front Under Cover")
  7. Remove the high voltage battery cover (A).

    Tightening torque : 7.8 - 11,8 N·m

  8. Disconnect the front high voltage junction box power cable (A).
    How to disconnect the connector
    1. Release the locking clip (A) by pulling it.
    2. Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).
  9. Remove the center floor rear under cover. (Refer to Motor and Reduction Gear System - "Rear Under Cover")
  10. Disconnect the Integrated Charge Control Unit (ICCU) connector (A).
    How to disconnect the connector
    1. Release the locking clip (A) by pulling it.
    2. Disconnect the connector while pressing the locking clip (B).
  11. Disconnect the rear high voltage junction box power cable (A).
    How to disconnect the connector
    1. Release the locking clip (A) by pulling it.
    2. Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).
  12. Measure the voltage between the high voltage power connector and high voltage battery terminal to check whether the high voltage is shut-off.
    30 V or less : Normal cut off high voltage circuit Above 30 V : Fault on high voltage circuit
    1. Measure the voltage between the high voltage power connector positive ( + ) terminal and negative ( - ) terminal.
    2. Measure the voltage between the high voltage battery positive ( + ) and negative ( - ) terminal.
    3. Measure the voltage between the high voltage battery positive ( + ) terminal and ground.
    4. Measure the voltage between the high voltage battery negative ( - ) terminal and ground.
    5. Measure the voltage between the rear high voltage battery positive ( + ) and negative ( - ) terminal.
    6. Measure the voltage between the rear high voltage battery positive ( + ) terminal and ground.
    7. Measure the voltage between the rear high voltage battery negative ( - ) terminal and ground.
    1. Check for insulation breakdown via KDS and physical leakage current before working on EV.
    2. Remove the main fuse if insulation breakdown or leakage current is suspected. (Remove the main fuse even when DTC CODE ON such as PRA malfunction) (Refer to High Voltage Battery Control System - "Main Fuse") ※ If there is no insulation breakdown or leakage current and it is normal, work without removing the main fuse.

Specification ➤

Special Service Tool

Special Service Tool

Tool Name / Number Illustration Description
Ball joint puller
09568 - 2J100
Used for removal of tie rod end
Lower arm ball joint remover
0K545 - A9100
Used for removal of front lower arm ball joint
Shock absorber lock nut remover.
0K546 - F6100
Used for removal or installing of front strut lock nut.
Shock absorber lock nut remover.
09546 - 3X100
Used for removal or installing of rear shock absorber lock nut.
Lower arm 'G' bushing replacement tool
09545 - AL100
Used for replacement of the lower arm 'G' bushing

Troubleshooting

Troubleshooting

Heavy weight feeling on steering wheel

Expected cause Countermeasure
Faulty front wheel alignment Adjust or repair
Over rotation resistance of lower arm ball joint Replace
Over rotation resistance of strut bearing Replace
Too low amount of tire air pressure Adjust

Steering wheel recovery trouble

Expected cause Countermeasure
Faulty front wheel alignment Adjust or repair

Noise or ride comfort trouble

Expected cause Countermeasure
Faulty wheel alignment Adjust or repair
Inappropriated tire air pressure Adjust
Faulty function of shock absorber Replace
Damaged coil spring Replace
Damaged stabilizer Replace
Damaged lower arm bushing Replace
Stabilizer link fixing nut got loose Retighten
Damaged stabilizer link (dust cover tearing, ring broke away) Replace

Abnormal worned out of tire

Expected cause Countermeasure
Faulty wheel alignment Adjust or repair
Inappropriated tire air pressure Adjust

Unstable steering wheel

Expected cause Countermeasure
Front wheel alignment trouble Adjust or repair
Lower arm ball joint turning resistance is too small Replace
Damaged lower arm bushing Replace

Vehicle pulls to one side

Expected cause Countermeasure
Wheel alignment trouble Adjust or repair
Unbalance of right/left tire Adjust or replace
Damaged or deformed lower arm bushing Replace
Damaged coil spring Replace

Steering wheel vibration

Expected cause Countermeasure
Front wheel alignment trouble Adjust or repair
Wheel balance trouble Adjust or repair
Lower are ball joint turning resistance is too much or too small Replace
Damaged stabilizer Replace
Damaged lower arm bushing Replace
Shock absorber operating trouble Replace
Coil spring trouble Replace

Under Body Parts Causing Abnormal Noise
Conditions for occurrence Abnormal noise on uneven ground
Parts Stabilizer bar link Stabilizer bar bushing Lower arm ball joint Strut insulator
Trouble area
Type of abnormal noise Rattling, Creaking noise Squeaking noise Clunking, Knocking noise Clicking, Creaking noise
Occurring area Under part Under part Under part Upper part
Driving speed 20 - 40 ㎞/h (12.4 - 25 mph) While low speed driving (20 - 40 ㎞/h (12.4 - 25 mph)) 20 - 40 ㎞/h (12.4 - 25 mph) -
Condition of road Uneven road / bump Uneven road / bump Uneven road / bump Uneven road / tough road
Reason Loosen / leakage (teared down) / corrosion Separation of bar and bushing / slip Loosen / leakage (teared down) / corrosion Tightened (decrease torque) and interference

Conditions for occurrence Abnormal noise while going through uneven road / tough road
Parts Strut / Shock absorber Strut / Shock absorber Strut / Shock absorber Strut / Shock absorber
Trouble area
Type of abnormal noise Rubbing noise Clicking, Creaking noise Rubbing noise Clicking noise
Occurring area Upper part Upper part Upper part (rear) Upper part (rear)
Driving speed 15 - 25 ㎞/h (9.3 - 15,5 mph) 15 - 25 ㎞/h (9.3 - 15,5 mph) 15 - 40 ㎞/h (9.3 - 25 mph) 30 - 50 ㎞/h (18.6 - 31 mph)
Condition of road Uneven road Uneven road Uneven road and tough road Tough road
Reason Friction sound from piston load and bumper rubber inner side Rolled down bumper rubber
(tapping sound of bumper rubber upper part and insulator under part)
Adhesion trouble of upper bracket rubber Suspension tuning trouble
(damping force, rubber characteristic)

Conditions for occurrence Abnormal noise on uneven road Abnormal noise while steering
Parts Lower arm "G" bushing Cross member bushing Strut bearing Wheel / Hub bearing
Trouble area
Type of strange sound Rubbing noise Clicking noise Clicking noise Roaring noise
Occurring area Under part Under part Upper part Lower and side part
Driving speed 10 - 40 ㎞/h (6.2 - 25 mph) - - 20 - 60 ㎞/h (12.4 - 37 mph)
Condition of road Bump / tough road Even road Even road Even road
Reason Dropped off / fallen off Dropped off / fallen off Grease leakage Damaged from outer impact, foreign substance inflow

Wheel and tire diagnosis Wheel /tire noise, vibration and harshness concerns are directly related to vehicle speed and are not generally affected by acceleration, coasting or deceleration. Also, out-of-balance wheel and tires can vibrate at more than one speed. A vibration that is affected by the engine rpm, or is eliminated by placing the transmission in Neutral is not related to the tire and wheel. As a general rule, tire and wheel vibrations felt in the steering wheel are related to the front tire and wheel assemblies. Vibrations felt in the seat or floor are related to the rear tire and wheel assemblies. This can initially isolate a concern to the front or rear. Careful attention must be paid to the tire and wheels. There are several symptoms that can be caused by damaged or worn tire and wheel. Perform a careful visual inspection of the tires and wheel assemblies. Spin the tires slowly and watch for signs of lateral or radial runout. Refer to the tire wear chart to determine the tire wear conditions and actions
Wheel and tire diagnosis
Rapid wear at the center Rapid wear at both shoulders Wear at one shoulder
  • Center-tread down to fabric due to excessively over inflated tires
  • Lack of rotation
  • Excessive toe on drive wheels
  • Heavy acceleration on drive
  • Under-inflated tires
  • Worn suspension components
  • Excessive cornering speeds
  • Lack of rotation
  • Toe adjustment out of specification
  • Camber out of specification
  • Damaged strut
  • Damaged lower arm
Partial wear Feathered edge Wear pattern
  • Damaged or worn brake discs
  • Sudden excessive braking
  • Toe adjustment out of specification
  • Damaged or worn tie rods
  • Damaged knuckle
  • Toe adjustment out of specification
  • Lack of rotation
  • Damaged suspension component

Front Suspension System ➤

Rear Suspension System ➤

Wheel and Tire ➤

Alignment ➤

Tire Pressure Monitoring System (TPMS) ➤