Maintenance

Power Train

102steps
~612min
4/5difficulty
02040608010058.843N·mlb·ft
Tightening torque found on this page
Done 0 of 102

Contents:

Reduction Gear Oil Repair procedures - Front Motor

Replacement

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related system, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
When checking the reduction gear oil level, be careful not to allow foreign substance (like dust) to enter through the filler hole.
  1. Remove the front under cover. (Refer to Front Motor and Reduction Gear System - "Front Under Cover")
  2. Prepare a clean 5 ℓ beaker (A) to measure the amount of oil.
  3. Remove the drain plug (A) and drain oil, and then reinstall the drain plug.

    Tightening torque : 44.1 - 59 N·m

    The existing drain plug gasket (A) must be replaced with a new one (do not reuse).
  4. Remove the front reduction gear cover fastener (A).
  5. Remove the filler plug (A).
  6. Fill the specified oil through the filler plug hole as much as it has been drained.

    Recommended : Kia genuine ATF SP4M-1

  7. Install the filler plug (A).

    Tightening torque : 44.1 - 59 N·m

    The existing filler plug gasket (A) must be replaced with a new one (do not reuse).
  8. Install the front reduction gear cover fastener (A).
  9. Install the front under cover. (Refer to Front Motor and Reduction Gear System - "Front Under Cover")

Reduction Gear Oil Repair procedures - Rear Motor

Replacement

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related system, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
When checking the reduction gear oil level, be careful not to allow foreign substance (like dust) to enter through the filler hole.
  1. Remove the rear under cover. (Refer to Rear Motor and Reduction Gear System - "Rear Under Cover")
  2. Prepare a clean 5 ℓ beaker (A) to measure the amount of oil.
  3. Remove the drain plug (A) and drain oil, and then reinstall the drain plug.

    Tightening torque : 44.1 - 59 N·m

    The existing drain plug gasket (A) must be replaced with a new one (do not reuse).
  4. Remove the filler plug (A).
  5. Fill the specified oil through the filler plug hole as much as it has been drained.

    Recommended : Kia genuine ATF SP4M-1

  6. Install the filler plug (A).

    Tightening torque : 44.1 - 59 N·m

    The existing filler plug gasket (A) must be replaced with a new one (do not reuse).
  7. Install the rear under cover. (Refer to Rear Motor and Reduction Gear System - "Rear Under Cover")

Coolant Drain

Special Service Tool

Tool Name / Number Illustration Description
Coolant refiller & suction tool
0K253 - J2300
Used to drain and fill the coolant for EV
Cap adapter
0K253 - J2320
Used to drain and fill the coolant for EV

SST (0K253 - J2300) Detail Name
1. Pressure Valve
2. Suction Valve
3. Vacuum Valve 1
4. Vacuum Valve 2
5. Coolant Injection
6. Vacuum Valve
7. Regulator Pressure Gauge
8. Pressure Gauge
9. Vacuum Gauge
10. Air Pressurization Valve
11. Vacuum Outlet Valve
12. Air Hose Inlet Valve
13. Regulator Adjusting Knob

Drain

  • When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
  • When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Disconnect the battery negative ( - ) terminal and the high voltage service interlock connector. (Refer to Battery Control System - "Battery (12 V)") (Refer to Battery Control System - "Battery (12 V)" - 4WD)
  2. Open the reservoir tank cap (A).
  3. Install the cap adapter (0K253 - J2320).
  4. Install the radiator cap connection hose (A) to the radiator cap adapter (B).
  5. Connect the radiator cap connection hose (A) to the air pressurization valve of SST (0K253 - J2300).
  6. Install the air hose (A) to the air inlet valve of SST (0K253 - J2300).
    Make sure all valves are closed.
  7. Turn the regulator adjusting knob (A) to set pressure gauge (B) to 0.2 Mpa.
    After adjusting the pressure, close the regulator adjustment knob.
  8. Remove the front under cover. (Refer to Motor & Reduction Gear System - "Front Under Cover")
  9. Release the quick connector, and then disconnect the high voltage battery EWP cooling hose (A). [2WD] [4WD]
  10. Install the coolant drain adapter and hose (A) to the battery EWP and EWP cooling hose. [2WD] [4WD]
  11. Put the opposite of the coolant drain adapter and hose (A) to a bucket (B).
  12. Turn the pressure valve (A) the direction of the arrow to drain coolant.
    Make sure that the valves other than the pressure valve (A) are closed.
  13. Close the pressure valve after draining coolant, and then install the high voltage battery EWP coolant hose (A). [2WD] [4WD]
  14. Remove the rear under cover. (Refer to Motor and Reduction Gear System - "Rear Under Cover")
  15. Disconnect the cooling hose (A) after releasing the quick connector.
  16. Install the coolant drain adapter and hose (A) to the cooling hose.
  17. Put the opposite of the coolant drain adapter and hose (A) to a bucket (B).
  18. Turn the pressure valve (A) the direction of the arrow to drain coolant.
    Make sure that the valves other than the pressure valve (A) are closed.
  19. Close the pressure valve after draining coolant, and then install the cooling hose (A).
  20. Separate the radiator cap connection hose (A) to the air pressurization valve.

Coolant Refilling

Special Service Tool

Tool Name / Number Illustration Description
Coolant refiller & suction tool
0K253 - J2300
Used to drain and fill the coolant for EV
Cap adapter
0K253 - J2320
Used to drain and fill the coolant for EV

SST (0K253 - J2300) Detail Name
1. Pressure Valve
2. Suction Valve
3. Vacuum Valve 1
4. Vacuum Valve 2
5. Coolant Injection
6. Vacuum Valve
7. Regulator Pressure Gauge
8. Pressure Gauge
9. Vacuum Gauge
10. Air Pressurization Valve
11. Vacuum Outlet Valve
12. Air Hose Inlet Valve
13. Regulator Adjusting Knob

Refilling

  • Be careful not to spill coolant on the electric devices when replacing the coolant.
  • Use genuine antifreeze/coolant.
  • To prevent corrosion, the concentration of coolant should be maintained at a minimum of 45%. If the coolant concentration is less than 45%, there may be a risk of corrosion or freezing.
  • It is not recommended if the concentration of the coolant exceeds 60%, as the cooling effect may be reduced.
  • Do not mix antifreeze/coolant from different brands.
  • Do not add any anti-rust.
  1. Drain the coolant. (Refer to Coolant - "Drain")
  2. Connect the radiator cap connection hose (A) to the vacuum valve of SST (0K253 - J2300).
  3. Open the vacuum valve (A) in the direction of the arrow, and then close when the vacuum gauge (B) reaches the green area (C).
    Make sure that the valves other than the vacuum valve (A) are closed.
  4. Connect the coolant suction hose (A) to SST (0K253 - J2300) coolant filler valve and place the opposite hose in the bucket (B) containing new coolant.
  5. Turn the suction valve (A) in the direction of the arrow to fill new coolant, and then close it when the vacuum gauge reaches to '0'.
    Check that the valve except the suction valve (A) is locked.
  6. Remove the cap adapter (0K253 - J2320).
  7. Perform the order below with the KDS. (S/W Management → Vehicle Control → Electric Water Pump Control)
    Charge the auxiliary 12 V battery during performing "Electric Water Pump Control" to prevent battery drain.
    When driving EWP, operate within 10 minutes.
  8. When the EWP operates and coolant circulates, refill coolant so that the coolant level is kept between "MAX" and "MIN" level.
    Friction may damage the bearing if the EWP is operated without coolant.
  9. When the operational sound volume of the EWP becomes small and when no air bubbles can be seen in the reservoir tank, bleeding of the coolant system is completed.
    • After air bleeding is completed make sure that coolant in the reservoir tank flow without air bubble during the EWP actuation.
    • If the coolant flow is not seen or air bubbles are still seen, repeat steps 7 to 8.
  10. Perform the order below with the KDS. (Actuation Test → Vehicle Control → Battery EWP Operation Mode for Degassing and Circulation)
    Charge the auxiliary 12 V battery during performing "Battery Electric Water Pump Control" to prevent battery drain.
    When driving EWP, operate within 10 minutes.
  11. When the battery EWP operates and coolant circulates, refill coolant so that the coolant level is kept between "MAX" and "MIN" level.
    Friction may damage the bearing if the EWP is operated without coolant.
  12. When the operational sound volume of the EWP becomes small and when no air bubbles can be seen in the reservoir tank, bleeding of the coolant system is completed.
    • After air bleeding is completed make sure that coolant in the reservoir flow without air bubble during the EWP actuation.
    • If the coolant flow is not seen or air bubbles are still seen, repeat steps 10 to 11.
  13. After air bleeding is completed, refill the coolant to the MAX level and install the reservoir cap.
  14. Check the coolant for leakage.
    The cooling system air bleeding and coolant injection are performed perfectly when the coolant is completely cooled. Check the coolant level of the reservoir tank for 2 - 3 days after flushing the coolant.
  15. Install the front under cover. (Refer to Motor & Reduction Gear System - "Front Under Cover")
  16. Install the rear under cover. (Refer to Motor and Reduction Gear System - "Rear Under Cover")

High Voltage Battery Coolant Drain

Special Service Tool

Tool Name / Number Illustration Description
Coolant refiller & suction tool
0K253 - J2300
Used to drain and fill the coolant for EV
Cap adapter
0K253 - J2320
Used to drain and fill the coolant for EV

SST (0K253 - J2300) Detail Name
1. Pressure Valve
2. Suction Valve
3. Vacuum Valve 1
4. Vacuum Valve 2
5. Coolant Injection
6. Vacuum Valve
7. Regulator Pressure Gauge
8. Pressure Gauge
9. Vacuum Gauge
10. Air Pressurization Valve
11. Vacuum Outlet Valve
12. Air Hose Inlet Valve
13. Regulator Adjusting Knob

Drain

  • When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
  • When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Disconnect the battery negative ( - ) terminal and the high voltage service interlock connector. (Refer to Battery Control System - "Battery (12 V)") (Refer to Battery Control System - "Battery (12 V)" - 4WD)
  2. Open the reservoir tank cap (A).
  3. Install the cap adapter (0K253 - J2320).
  4. Install the radiator cap connection hose (A) to the radiator cap adapter (B).
  5. Connect the radiator cap connection hose (A) to the air pressurization valve of SST (0K253 - J2300).
  6. Install the air hose (A) to the air inlet valve of SST (0K253 - J2300).
    Make sure all valves are closed.
  7. Turn the regulator adjusting knob (A) to set pressure gauge (B) to 0.2 Mpa.
    After adjusting the pressure, close the regulator adjustment knob.
  8. Remove the front under cover. (Refer to Motor & Reduction Gear System - "Front Under Cover")
  9. Release the quick connector, and then disconnect the high voltage battery EWP cooling hose (A). [2WD] [4WD]
  10. Install the coolant drain adapter and hose (A) to the battery EWP and EWP cooling hose. [2WD] [4WD]
  11. Put the opposite of the coolant drain adapter and hose (A) to a bucket (B).
  12. Turn the pressure valve (A) the direction of the arrow to drain coolant.
    Make sure that the valves other than the pressure valve (A) are closed.
  13. Close the pressure valve after draining coolant, and then install the high voltage battery EWP coolant hose (A). [2WD] [4WD]
  14. Separate the radiator cap connection hose (A) to the air pressurization valve.

High Voltage Battery Coolant Refilling

Special Service Tool

Tool Name / Number Illustration Description
Coolant refiller & suction tool
0K253 - J2300
Used to drain and fill the coolant for EV
Cap adapter
0K253 - J2320
Used to drain and fill the coolant for EV

SST (0K253 - J2300) Detail Name
1. Pressure Valve
2. Suction Valve
3. Vacuum Valve 1
4. Vacuum Valve 2
5. Coolant Injection
6. Vacuum Valve
7. Regulator Pressure Gauge
8. Pressure Gauge
9. Vacuum Gauge
10. Air Pressurization Valve
11. Vacuum Outlet Valve
12. Air Hose Inlet Valve
13. Regulator Adjusting Knob

Refilling

  • Be careful not to spill coolant on the electric devices when replacing the coolant.
  • Use genuine antifreeze/coolant.
  • To prevent corrosion, the concentration of coolant should be maintained at a minimum of 45%. If the coolant concentration is less than 45%, there may be a risk of corrosion or freezing.
  • It is not recommended if the concentration of the coolant exceeds 60%, as the cooling effect may be reduced.
  • Do not mix antifreeze/coolant from different brands.
  • Do not add any anti-rust.
  1. Drain the high voltage battery coolant. (Refer to High Voltage Battery Coolant - "Drain")
  2. Connect the radiator cap connection hose (A) to the vacuum valve of SST (0K253 - J2300).
  3. Open the vacuum valve (A) in the direction of the arrow, and then close when the vacuum gauge (B) reaches the green area (C).
    Make sure that the valves other than the vacuum valve (A) are closed.
  4. Connect the coolant suction hose (A) to SST (0K253 - J2300) coolant filler valve and place the opposite hose in the bucket (B) containing new coolant.
  5. Turn the suction valve (A) in the direction of the arrow to fill new coolant, and then close it when the vacuum gauge reaches to '0'.
    Check that the valve except the suction valve (A) is locked.
  6. Remove the cap adapter (0K253 - J2320).
  7. Perform the order below with the KDS. (Actuation Test → Vehicle Control → Battery EWP Operation Mode for Degassing and Circulation)
    Charge the auxiliary 12 V battery during performing "Battery Electric Water Pump Control" to prevent battery drain.
    When driving EWP, operate within 10 minutes.
  8. When the battery EWP operates and coolant circulates, refill coolant so that the coolant level is kept between "MAX" and "MIN" level.
    Friction may damage the bearing if the EWP is operated without coolant.
  9. When the operational sound volume of the EWP becomes small and when no air bubbles can be seen in the reservoir tank, bleeding of the coolant system is completed.
    • After air bleeding is completed make sure that coolant in the reservoir tank flow without air bubble during the EWP actuation.
    • If the coolant flow is not seen or air bubbles are still seen, repeat steps 7 to 8.
  10. After air bleeding is completed, refill the coolant to the MAX level and install the reservoir cap.
  11. Check the coolant for leakage.
    The cooling system air bleeding and coolant injection are performed perfectly when the coolant is completely cooled. Check the coolant level of the reservoir tank for 2 - 3 days after flushing the coolant.
  12. Install the front under cover. (Refer to Motor & Reduction Gear System - "Front Under Cover")

Motor Coolant Drain

Special Service Tool

Tool Name / Number Illustration Description
Coolant refiller & suction tool
0K253 - J2300
Used to drain and fill the coolant for EV
Cap adapter
0K253 - J2320
Used to drain and fill the coolant for EV

SST (0K253 - J2300) Detail Name
1. Pressure Valve
2. Suction Valve
3. Vacuum Valve 1
4. Vacuum Valve 2
5. Coolant Injection
6. Vacuum Valve
7. Regulator Pressure Gauge
8. Pressure Gauge
9. Vacuum Gauge
10. Air Pressurization Valve
11. Vacuum Outlet Valve
12. Air Hose Inlet Valve
13. Regulator Adjusting Knob

Drain

  • When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
  • When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Disconnect the battery negative ( - ) terminal and the high voltage service interlock connector. (Refer to Battery Control System - "Battery (12 V)") (Refer to Battery Control System - "Battery (12 V)" - 4WD)
  2. Open the reservoir tank cap (A).
  3. Install the cap adapter (0K253 - J2320).
  4. Install the radiator cap connection hose (A) to the radiator cap adapter (B).
  5. Connect the radiator cap connection hose (A) to the air pressurization valve of SST (0K253 - J2300).
  6. Install the air hose (A) to the air inlet valve of SST (0K253 - J2300).
    Make sure all valves are closed.
  7. Turn the regulator adjusting knob (A) to set pressure gauge (B) to 0.2 Mpa.
    After adjusting the pressure, close the regulator adjustment knob.
  8. Remove the rear under cover. (Refer to Motor and Reduction Gear System - "Rear Under Cover")
  9. Disconnect the cooling hose (A) after releasing the quick connector.
  10. Install the coolant drain adapter and hose (A) to the cooling hose.
  11. Put the opposite of the coolant drain adapter and hose (A) to a bucket (B).
  12. Turn the pressure valve (A) the direction of the arrow to drain coolant.
    Make sure that the valves other than the pressure valve (A) are closed.
  13. Close the pressure valve after draining coolant, and then install the cooling hose (A).
  14. Separate the radiator cap connection hose (A) to the air pressurization valve.

Motor Coolant Refilling

Special Service Tool

Tool Name / Number Illustration Description
Coolant refiller & suction tool
0K253 - J2300
Used to drain and fill the coolant for EV
Cap adapter
0K253 - J2320
Used to drain and fill the coolant for EV

SST (0K253 - J2300) Detail Name
1. Pressure Valve
2. Suction Valve
3. Vacuum Valve 1
4. Vacuum Valve 2
5. Coolant Injection
6. Vacuum Valve
7. Regulator Pressure Gauge
8. Pressure Gauge
9. Vacuum Gauge
10. Air Pressurization Valve
11. Vacuum Outlet Valve
12. Air Hose Inlet Valve
13. Regulator Adjusting Knob

Refilling

  • Be careful not to spill coolant on the electric devices when replacing the coolant.
  • Use genuine antifreeze/coolant.
  • To prevent corrosion, the concentration of coolant should be maintained at a minimum of 45%. If the coolant concentration is less than 45%, there may be a risk of corrosion or freezing.
  • It is not recommended if the concentration of the coolant exceeds 60%, as the cooling effect may be reduced.
  • Do not mix antifreeze/coolant from different brands.
  • Do not add any anti-rust.
  1. Drain the motor coolant. (Refer to Motor Coolant - "Drain")
  2. Connect the radiator cap connection hose (A) to the vacuum valve of SST (0K253 - J2300).
  3. Open the vacuum valve (A) in the direction of the arrow, and then close when the vacuum gauge (B) reaches the green area (C).
    Make sure that the valves other than the vacuum valve (A) are closed.
  4. Connect the coolant suction hose (A) to SST (0K253 - J2300) coolant filler valve and place the opposite hose in the bucket (B) containing new coolant.
  5. Turn the suction valve (A) in the direction of the arrow to fill new coolant, and then close it when the vacuum gauge reaches to '0'.
    Check that the valve except the suction valve (A) is locked.
  6. Remove the cap adapter (0K253 - J2320).
  7. Perform the order below with the KDS. (S/W Management → Vehicle Control → Electric Water Pump Control)
    Charge the auxiliary 12 V battery during performing "Electric Water Pump Control" to prevent battery drain.
    When driving EWP, operate within 10 minutes.
  8. When the EWP operates and coolant circulates, refill coolant so that the coolant level is kept between "MAX" and "MIN" level.
    Friction may damage the bearing if the EWP is operated without coolant.
  9. When the operational sound volume of the EWP becomes small and when no air bubbles can be seen in the reservoir tank, bleeding of the coolant system is completed.
    • After air bleeding is completed make sure that coolant in the reservoir tank flow without air bubble during the EWP actuation.
    • If the coolant flow is not seen or air bubbles are still seen, repeat steps 7 to 8.
  10. Install the rear under cover. (Refer to Motor and Reduction Gear System - "Rear Under Cover")