Body (Interior / Exterior / Electrical)

15steps
~90min
4/5difficulty
010203040509.87N·mlb·ft
Tightening torque found on this page
Done 0 of 15

Contents:

Single-Use Parts

Single-Use Parts

Non-reusable parts (Single-Use Parts) Workshop manual provides “Components and Components Location” which can be used to identify “Non-reusable parts”. When repairing a vehicle, Non-reusable parts such as fasteners, gaskets, washers, clips and garnishes must be replaced. Kia Non-reusable parts are designed to be installed only once. Before working on a vehicle, check “Components and Components Location” to find the non-reusable parts in a system. ※ Symbol of Non-reusable parts
Symbol Meaning
Do not reuse the part. Replace with a new one.

※ Example of “Components a470nd Components Location”

High Voltage System General Safety Information and Caution ➤

High Voltage Shut-off Procedures

High Voltage Shut-off Procedures

High Voltage Shut-off Procedures

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
High Voltage Component : Battery System Assembly (BSA), motor assembly, inverter assembly, high voltage junction box, power cable, etc.
  1. Check the Battery Management Unit (BMU) weld flag with the KDS. (Data Analysis → Battery Management System (BMS) → BMU Weld Flag)

    Specified value : NO

    Refer to the KDS screen for operating conditions and details.
  2. Open the front trunk (A).
  3. Open the low voltage (12 V) battery service cover (A).
  4. Turn the POWER OFF, separate the low voltage (12 V) battery ( - ) terminal (A).

    Tightening torque : 7.8 - 9,8 N·m

  5. Disconnect the service interlock connector (A).
    • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
    • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
    The service interlock connector cannot be completely removed.
  6. Remove the front under cover. (Refer to Motor and Reduction Gear System - "Front Under Cover")
  7. Remove the high voltage battery cover (A).

    Tightening torque : 7.8 - 11,8 N·m

  8. Disconnect the front high voltage junction box power cable (A).
    How to disconnect the connector
    1. Release the locking clip (A) by pulling it.
    2. Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).
  9. Remove the center floor rear under cover. (Refer to Motor and Reduction Gear System - "Rear Under Cover")
  10. Disconnect the Integrated Charge Control Unit (ICCU) connector (A).
    How to disconnect the connector
    1. Release the locking clip (A) by pulling it.
    2. Disconnect the connector while pressing the locking clip (B).
  11. Disconnect the rear high voltage junction box power cable (A).
    How to disconnect the connector
    1. Release the locking clip (A) by pulling it.
    2. Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).
  12. Measure the voltage between the high voltage power connector and high voltage battery terminal to check whether the high voltage is shut-off.
    30 V or less : Normal cut off high voltage circuit Above 30 V : Fault on high voltage circuit
    1. Measure the voltage between the high voltage power connector positive ( + ) terminal and negative ( - ) terminal.
    2. Measure the voltage between the high voltage battery positive ( + ) and negative ( - ) terminal.
    3. Measure the voltage between the high voltage battery positive ( + ) terminal and ground.
    4. Measure the voltage between the high voltage battery negative ( - ) terminal and ground.
    5. Measure the voltage between the rear high voltage battery positive ( + ) and negative ( - ) terminal.
    6. Measure the voltage between the rear high voltage battery positive ( + ) terminal and ground.
    7. Measure the voltage between the rear high voltage battery negative ( - ) terminal and ground.
    1. Check for insulation breakdown via KDS and physical leakage current before working on EV.
    2. Remove the main fuse if insulation breakdown or leakage current is suspected. (Remove the main fuse even when DTC CODE ON such as PRA malfunction) (Refer to High Voltage Battery Control System - "Main Fuse") ※ If there is no insulation breakdown or leakage current and it is normal, work without removing the main fuse.

Service Inspection Mode

Service Inspection Mode

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
The service mode is used to safely perform actuation test or S/W Management related to the battery management system while keeping the Main Relay OFF.
  • The acuation test with the KDS is possible in only the service mode.
  • In service mode, it is impossible to charge the high voltage battery and using the indoor/outdoor V2L.
  1. Enter the service mode as ordered below after stopping the vehicle and opening the driver's side door.
    1. Turn the POWER ON. (Do not EV READY.)
    2. Press the audio scroll on the right side of the steering wheel and maintain it.
    3. Input the trip scroll on the left side of the steering wheel 5 times to upward within 5 seconds.
      All doors (including the hood and trunk) must be kept in a closed state, excluding the driver's side door.
  2. "Service Mode" lamp turns on in the Cluster when the vehicle is in servic inspection mode. Check that the “Service Mode” lamp is turns on to ensure that service inspection mode is entered correctly. Check that entering the service mode was normally done through the cluster.
    Normal : The cluster's "Service Mode" lamp turns on and turns off after about 3 seconds.
    • If the entering to the service mode fails, retry from 1 step.
    • It is impossible to change from the service mode to EV READY.
  3. The service mode is deactivated when the POWER OFF.

Troubleshooting

Troubleshooting

Wind Noise
Suspected Causes Repair
Door weatherstrip Reassembly or replacement

Water Leaks
Suspected Causes Repair
The seal of windshield and tailgate glass Apply sealant

Mechanical Problem Opening and Closing of hood, Tailgate
Suspected Causes Repair
Engagement of hinge, striker or latch Adjustment
The height of the overslam bumper Adjustment

Opening and Closing of Door
Suspected Causes Repair
Engagement of hinge, striker Adjustment
Door handle, latch, checker Replacement
Lack of grease of door hinge and checker Apply grease

Window Glass
Suspected Causes Repair
Assembly of positioning window glass Adjustment
Motor or regulator Replacement

Outside Handle
Suspected Causes Repair
Outside handle does not deploy Open the door with the inside handle to check that the outside handle deploys
- When deployed : Check the door latch and previous step (FOB / BDC / PDC)
- When it is not deployed : Check the outside handle and SBCM
Outside handle does not retract Check by opening the door with the outside handle
- When the door is opened : Check the door latch and the previous step (FOB / BDC / PDC)
- When the door is not opened: Check the outside handle and SBCM
Caught in the panel when deploying/retracting the outside handle Reassembling the outside handle

Operating sequence : FOB → BDC → PDC → Door latch operation → SBCM → Outside handle
  • Door latch 'locked' state → Outside handle 'deployed'
  • Door latch 'unlocked' state → Outside handle 'retracted'

Special Service Tools

Special Service Tool

Tool Name / Number Illustration Description
Outside rear view mirror glass remover tool
0K876 - L2100
Used when removing outside rear view mirror glass
Outside view mirror assembly fixing stand
0K876 - C5100
Used when fixing the outside rear view mirror assembly

Specification ➤

Body Side Molding ➤

Crash Pad ➤

Driver & Driving Assistance System ➤

Exterior Green House ➤

Fender ➤

Floor Console ➤

Front & Rear Bumper ➤

Front Door ➤

Front End Module ➤

Front Seat ➤

Hood ➤

Infotainment System ➤

Interior Trim ➤

Light & Vision System ➤

Luggage Trim ➤

Mirror ➤

Rear Door ➤

Rear Seat ➤

Roof Trim ➤

Security & Vehicle Ignition System ➤

Sunroof ➤

Tailgate ➤