Non-reusable parts (Single-Use Parts) Workshop manual provides “Components and Components Location” which can be used to identify “Non-reusable parts”. When repairing a vehicle, Non-reusable parts such as fasteners, gaskets, washers, clips and garnishes must be replaced. Kia Non-reusable parts are designed to be installed only once. Before working on a vehicle, check “Components and Components Location” to find the non-reusable parts in a system. ※ Symbol of Non-reusable parts
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
High Voltage Component : Battery System Assembly (BSA), motor assembly, inverter assembly, high voltage junction box, power cable, etc.
Check the Battery Management Unit (BMU) weld flag with the KDS. (Data Analysis → Battery Management System (BMS) → BMU Weld Flag)
Specified value : NO
Refer to the KDS screen for operating conditions and details.
Open the front trunk (A).
Open the low voltage (12 V) battery service cover (A).
Turn the POWER OFF, separate the low voltage (12 V) battery ( - ) terminal (A).
Tightening torque : 7.8 - 9,8 N·m
Disconnect the service interlock connector (A).
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
The service interlock connector cannot be completely removed.
Remove the front under cover. (Refer to Motor and Reduction Gear System - "Front Under Cover")
Remove the high voltage battery cover (A).
Tightening torque : 7.8 - 11,8 N·m
Disconnect the front high voltage junction box power cable (A).
How to disconnect the connector
Release the locking clip (A) by pulling it.
Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).
Remove the center floor rear under cover. (Refer to Motor and Reduction Gear System - "Rear Under Cover")
Disconnect the Integrated Charge Control Unit (ICCU) connector (A).
How to disconnect the connector
Release the locking clip (A) by pulling it.
Disconnect the connector while pressing the locking clip (B).
Disconnect the rear high voltage junction box power cable (A).
How to disconnect the connector
Release the locking clip (A) by pulling it.
Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).
Measure the voltage between the high voltage power connector and high voltage battery terminal to check whether the high voltage is shut-off. 30 V or less : Normal cut off high voltage circuit Above 30 V : Fault on high voltage circuit
Measure the voltage between the high voltage power connector positive ( + ) terminal and negative ( - ) terminal.
Measure the voltage between the high voltage battery positive ( + ) and negative ( - ) terminal.
Measure the voltage between the high voltage battery positive ( + ) terminal and ground.
Measure the voltage between the high voltage battery negative ( - ) terminal and ground.
Measure the voltage between the rear high voltage battery positive ( + ) and negative ( - ) terminal.
Measure the voltage between the rear high voltage battery positive ( + ) terminal and ground.
Measure the voltage between the rear high voltage battery negative ( - ) terminal and ground.
Check for insulation breakdown via KDS and physical leakage current before working on EV.
Remove the main fuse if insulation breakdown or leakage current is suspected. (Remove the main fuse even when DTC CODE ON such as PRA malfunction) (Refer to High Voltage Battery Control System - "Main Fuse") ※ If there is no insulation breakdown or leakage current and it is normal, work without removing the main fuse.
Important Safety Notice
General Information
How to Use This Manual
Proper service methods and repair procedures are essential for safe, reliable operation of all electric vehicles as well as personal safety of the operator. The service procedures and descriptions in this shop manual provide general directions for a service and repair. Procedure, techniques, tools, and parts for service including the skill of the technician vary. It is impossible to provide advice or caution as to each case in this manual. Accordingly, anyone who intends to use a replacement part, service procedure, or tool, which is not recommended by the vehicle manufacturer, must first assure thoroughly that neither their personal safety nor the safe operation of the vehicle will be first jeopardized by the replacement part, service procedure, or tool they select.
Important Safety Information Types
Reminds you be very careful for those works may have high possibility of death or serious injury.
Reminds you be very careful for those works may have possibility of death or serious injury.
Reminds you be very careful for those works may have possibility of personal injury.
Gives you information that will prevent you from making errors that could damage the vehicle.
Gives you some information that will help you to complete the repair or procedure.
Precautions for Service
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage. (Refer to General Information - "High Voltage Shut-off Procedures")
When working on high voltage system or related system, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur. (Refer to General Information - "High Voltage System General Safety Information and Caution")
You must take the high voltage shut-off procedure before starting any work related with the high voltage or electrical system components in order to prevent fire or electric shock.
Do not smoke during work and do not work near fire hazards like heaters.
Keep a fire extinguisher nearby.
Use a lift designed for the vehicle when working underneath the vehicle. Refer to the lift points and precautions when using a vehicle lift. (Refer to General Information - "Lift and Support Points")
It is better not to work if you are feeling sick. The risk of injury increases and the quality of the vehicle after delivery to customer cannot be guaranteed.
When handling harmful substances and machine tools, wear appropriate goggles, gloves and cloth.
If hair, clothing, or jewelry is caught into the machine, it can cause serious injury. Do not wear ties, scarves, or necklaces and tie long hair behind your head when working.
Do not reuse worn or deformed fasteners, nuts and bolts. Some parts are prohibited for reuse. Follow instructions for those reuse prohibit parts in the manual.
Friction parts such as brake pads and clutch discs may contain asbestos fibers. Be careful not to inhale asbestos fibers when grinding, sanding.
Always keep the draining fuel, oil, brake fluid on a suitable container during work.
The air conditioning (A/C) system is filled with harmful refrigerants. The A/C system should only be serviced by certified technicians using approved refrigerant recovery/recycling equipment in the correct manner.
Identification Numbers
General Information
Identification Numbers
Vehicle Identification Number (VIN) The VIN is located under the front passenger seat.
Vehicle production sequence number - 000001 ~ 999999
Motor Number
Front Motor
Rear Motor
Motor model - EM : EV
Motor type - 07 : 73kW - 17 : 160kW - 27 : 270kW
Production year (Except I,O,Q,U,Z) S : 2025, T : 2025, V : 2027, W : 2028, X : 2029
Production month - 1~ 9 : January - September - A ~ C : October - December
Production day - 1~ 9 : 1st - 9th - A ~ Y : 10th - 31st (I, O, Q excluded)
Motor production sequence number - 001 ~ Z99 - A : 10 ~ Z : 32 - Z99 : 3299
Vehicle line - 1
Manufacturing Plant - J : Chungju (Korea) - C : China - D : Daegu (Korea)
Color code
Code
Item
Color
SWP
Snow White Pearl
ABP
Aurora Black Pearl
B4U
Gravity Blue
CR5
Runway Red
AGT
Interstella Gray
DU3
Yacht Blue
G4E
Deep Forest Green
KLM
Moonscape matt gray
GLB
Glacier
Warning And Caution Labels
General Information
Warning And Caution Labels
1. Battery caution label 2. Pressure cap caution label
Auxiliary Battery Caution Label
A.
No flames
B.
Wear eye protection
C.
Prohibit access of children
D.
Caution battery electrolyte
E.
Information manual
F.
Explosion caution
G.
Waste recycling
Precautions for handling batteries
You must be aware of general safety precautions when installing, re-charging or handling the battery. Failure to handle the battery may result in explosions, suffocation or addiction.
Wear eye protection, Insulated gloves, and protection masks.
Keep lighted cigarettes and all other flames or sparks away from the battery.
Do not intentionally disassemble the battery.
Be sure to keep the battery in the horizontal position when storing, handling or carrying it.
Do not work around the battery while it is re-charging or discharging.
Always provide ventilation when working in an enclosed space.
Be careful of flames which occurs due to the short circuit while working with metal tools or conductors.
If any electrolyte gets into your eyes, flush your eyes with clean water for at least 15 minutes and get immediate medical attention.
If ingestion of electrolyte occurs, drink large amounts of water or milk and take a medical care quickly. Do not induce vomiting.
Check if the charging cable is damaged when charging the battery. Charging the battery with damaged cable may cause explosion or battery health dicrease.
If the battery becomes hot while charging, there can be explosion risk due to the generation of gas. Decrease the charging voltage or stop charging.
How to store the battery
Handling and storage
Store the battery in a cool, dry place and keep away from direct sunlight.
If storing the battery in a place over 25 ºC (77 ºF ), it affects to the battery life.
Store the battery when removing from the vehicle.
Check if the battery is fully charged and perform additional charging every 2 months.
Remove the corrosion on terminals and connectors by brushing with the mixture of baking soda and water to prevent the deterioration of the battery due to storing it in corrosive condition.
Before installing, apply the grease on the battery to reuse it.
Vehicle parked for an extended period of time
Disconnect the battery from the vehicle and charge the battery as much as possible. Store the fully charged battery in cool and dry area. If the battery is fully charged, it can be stored below 0 ºC (32 ºF ), but if not it can be frozen.
Regular operating vehicle
Check if the battery is leaking, damaged or cleaned regularly. Check the charging status of the battery regularly. Inspect the vehicle when the battery is discharged or overcharged. If the battery performance deteriorates, replace the battery.
Lift And Support Points
General Information
Lift Points And Precautions For Lift
Become familiar with the following instructions below when using lift.
Keep the vehicle empty and remove additional weight when lifting with lift. If it is inevitable, be careful not to exceeds the maximum weight of the lift.
Use the counter weight or install the safety jack to prevent the vehicle from falling when removing heavy parts such as motor or battery.
Install the rubber block to prevent the lift points from damage.
Before operating the lift, make sure there is no tool, parts, equipment, or people under the vehicle.
Follow the safety instructions in the manual provided by the lift manufactuer.
Install jacks using only provided lift points in this manual. [Lift Points]
[Precautions for 2 Post Lift]
Place the vehicle on the lift to balance the front, rear, left and right sides of the vehicle slowly so that the vehicle is centered on the lift.
For safety, lift the vehicle that it slightly falls off the ground, and then shake the vehicle to check the support condition.
If safety checked, lift the vehicle.
Place the vehicle on the lift to balance the front, rear, left and right sides of the vehicle slowly so that the vehicle centered on the lift.
Use wheel chocks to prevent vehicle moved accidentally.
Be careful not to let the lift interfere with underbody parts when lifting the vehicle.
Use wheel chocks to prevent vehicle moved accidentally.
Do not install the floor jack except for the front subframe, rear crossmember, and lift points.
[Precautions for 4 Post Lift] [Precautions for Scissor Lift] [Precautions for Floor Jack]
Towing
General Information
Towing
Be sure to follow the procedures below when towing.
Avoid towing a vehicle heavier than the vehicle doing the towing.
Press the brake pedal hard during braking as the performance may be reduced more than usual.
As the steering wheel operation may not be normal due to towing, drive with increased caution and with firm steering grip when driving.
When driving down a long hill, the brakes may overheat and brake performance will be reduced, therefore stop the from the driver when in vehicle.
When towing, passengers need to sit as far as possible from the from the driver when in vehicle.
The side airbags may deploy if the vehicle is in "Ready (On)" mode. be sure to turn off the vehicle before towing.
Towing hook Towing hook can be installed at the front and back of the vehicle.
To prevent vehicle body damage, connect the towing hook when towing.
Remove the cover by pressing the bottom of the bumper cover hole. [Front] [Rear]
Insert the towing hook by turning it clockwise into the hole until it is fully secured. [Front] [Rear]
Before towing, make sure the hook is installed properly.
How to tow with tow-truck These three methods can be used to tow for general vehicles. However, the sling-type towing method is not recommended as it may damage the vehicle except for the emergency situation.
Flatbed towing A method of towing by loading a vehicle behind a tow truck. It is the safest and best way to tow a electric vehicle.
Under lift towing A method of lifting the drive shaft wheel of the vehicle to the tow truck and making the opposite wheel touch the floor or towing using auxiliary equipment. * For electric vehicles, be sure to use auxiliary equipment such as dolly to prevent wheels from touching the ground.
Sling type towing A method of towing using a tow truck's hooked chain. Sling type towing is not recommended as it can seriously damage the vehicle's suspension and body.
To prevent the damage of the vehicle, electric vehicles must be towed by flat bed towing method or under lift towing method. When using under lift method, auxiliary equipment such as dolly must be used to prevent wheels from touching the ground.
When using under lift towing method, auxiliary equipment such as dolly must be used to prevent wheels from touching the ground.
Basic Service Symbols
General Information
Basic Service Symbols
These symbols indicate the part to apply such materials during service.