Cooling System
In this manual: Cooling System
12steps
~72min
3/5difficulty
Done 0 of 12
Contents:
Single-Use Parts
Single-Use Parts
Non-reusable parts (Single-Use Parts) Workshop manual provides “Components and Components Location” which can be used to identify “Non-reusable parts”. When repairing a vehicle, Non-reusable parts such as fasteners, gaskets, washers, clips and garnishes must be replaced. Kia Non-reusable parts are designed to be installed only once. Before working on a vehicle, check “Components and Components Location” to find the non-reusable parts in a system. ※ Symbol of Non-reusable parts| Symbol | Meaning |
| Do not reuse the part. Replace with a new one. |
※ Example of “Components and Components Location”
High Voltage System General Safety Information and Caution ➤
High Voltage Shut-off Procedures
High Voltage Shut-off Procedures
High Voltage Shut-off Procedures
|
| High Voltage Component : Battery System Assembly (BSA), motor assembly, inverter assembly, high voltage junction box, power cable, etc. |
- Check the Battery Management Unit (BMU) weld flag with the KDS. (Data Analysis → Battery Management System (BMS) → BMU Weld Flag)
Specified value : NO
Refer to the KDS screen for operating conditions and details. - Open the front trunk (A).
- Open the low voltage (12 V) battery service cover (A).
- Turn the POWER OFF, separate the low voltage (12 V) battery ( - ) terminal (A).
Tightening torque : 7.8 - 9,8 N·m
- Disconnect the service interlock connector (A).
- Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
- When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
The service interlock connector cannot be completely removed. - Remove the front under cover. (Refer to Motor and Reduction Gear System - "Front Under Cover")
- Remove the high voltage battery cover (A).
Tightening torque : 7.8 - 11,8 N·m
- Disconnect the front high voltage junction box power cable (A).
How to disconnect the connector - Release the locking clip (A) by pulling it.
- Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).
- Remove the center floor rear under cover. (Refer to Motor and Reduction Gear System - "Rear Under Cover")
- Disconnect the Integrated Charge Control Unit (ICCU) connector (A).
How to disconnect the connector - Release the locking clip (A) by pulling it.
- Disconnect the connector while pressing the locking clip (B).
- Disconnect the rear high voltage junction box power cable (A).
How to disconnect the connector - Release the locking clip (A) by pulling it.
- Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).
- Measure the voltage between the high voltage power connector and high voltage battery terminal to check whether the high voltage is shut-off.
30 V or less : Normal cut off high voltage circuit Above 30 V : Fault on high voltage circuit
- Measure the voltage between the high voltage power connector positive ( + ) terminal and negative ( - ) terminal.
- Measure the voltage between the high voltage battery positive ( + ) and negative ( - ) terminal.
- Measure the voltage between the high voltage battery positive ( + ) terminal and ground.
- Measure the voltage between the high voltage battery negative ( - ) terminal and ground.
- Measure the voltage between the rear high voltage battery positive ( + ) and negative ( - ) terminal.
- Measure the voltage between the rear high voltage battery positive ( + ) terminal and ground.
- Measure the voltage between the rear high voltage battery negative ( - ) terminal and ground.
- Check for insulation breakdown via KDS and physical leakage current before working on EV.
- Remove the main fuse if insulation breakdown or leakage current is suspected. (Remove the main fuse even when DTC CODE ON such as PRA malfunction) (Refer to High Voltage Battery Control System - "Main Fuse") ※ If there is no insulation breakdown or leakage current and it is normal, work without removing the main fuse.
Specification ➤
Special Service Tools. Flow Diagram
Special Service Tools
Special Service Tool
| Tool Name / Number | Illustration | Description |
| Coolant refiller & suction tool 0K253 - J2300 |
Used to drain and fill the coolant for EV | |
| Cap adapter 0K253 - J2320 |
Used to drain and fill the coolant for EV |
Flow Diagram
Coolant Flow
■ Heat Pump HTR : High-Temperature Radiator LTR : Low-Temperature Radiator ■ Non Heat Pump HTR : High-Temperature Radiator LTR : Low-Temperature RadiatorHigh Voltage Battery Cooling System ➤
Cooling System ➤
Motor Cooling System ➤
Was this page helpful?