Steering System

19steps
~114min
4/5difficulty
010203040509.87N·mlb·ft
Tightening torque found on this page
Done 0 of 19

Contents:

Single-Use Parts

Single-Use Parts

Non-reusable parts (Single-Use Parts) Workshop manual provides “Components and Components Location” which can be used to identify “Non-reusable parts”. When repairing a vehicle, Non-reusable parts such as fasteners, gaskets, washers, clips and garnishes must be replaced. Kia Non-reusable parts are designed to be installed only once. Before working on a vehicle, check “Components and Components Location” to find the non-reusable parts in a system. ※ Symbol of Non-reusable parts
Symbol Meaning
Do not reuse the part. Replace with a new one.

※ Example of “Components and Components Location”

High Voltage System General Safety Information and Caution ➤

High Voltage Shut-off Procedures

High Voltage Shut-off Procedures

High Voltage Shut-off Procedures

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
High Voltage Component : Battery System Assembly (BSA), motor assembly, inverter assembly, high voltage junction box, power cable, etc.
  1. Check the Battery Management Unit (BMU) weld flag with the KDS. (Data Analysis → Battery Management System (BMS) → BMU Weld Flag)

    Specified value : NO

    Refer to the KDS screen for operating conditions and details.
  2. Open the front trunk (A).
  3. Open the low voltage (12 V) battery service cover (A).
  4. Turn the POWER OFF, separate the low voltage (12 V) battery ( - ) terminal (A).

    Tightening torque : 7.8 - 9,8 N·m

  5. Disconnect the service interlock connector (A).
    • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
    • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
    The service interlock connector cannot be completely removed.
  6. Remove the front under cover. (Refer to Motor and Reduction Gear System - "Front Under Cover")
  7. Remove the high voltage battery cover (A).

    Tightening torque : 7.8 - 11,8 N·m

  8. Disconnect the front high voltage junction box power cable (A).
    How to disconnect the connector
    1. Release the locking clip (A) by pulling it.
    2. Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).
  9. Remove the center floor rear under cover. (Refer to Motor and Reduction Gear System - "Rear Under Cover")
  10. Disconnect the Integrated Charge Control Unit (ICCU) connector (A).
    How to disconnect the connector
    1. Release the locking clip (A) by pulling it.
    2. Disconnect the connector while pressing the locking clip (B).
  11. Disconnect the rear high voltage junction box power cable (A).
    How to disconnect the connector
    1. Release the locking clip (A) by pulling it.
    2. Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).
  12. Measure the voltage between the high voltage power connector and high voltage battery terminal to check whether the high voltage is shut-off.
    30 V or less : Normal cut off high voltage circuit Above 30 V : Fault on high voltage circuit
    1. Measure the voltage between the high voltage power connector positive ( + ) terminal and negative ( - ) terminal.
    2. Measure the voltage between the high voltage battery positive ( + ) and negative ( - ) terminal.
    3. Measure the voltage between the high voltage battery positive ( + ) terminal and ground.
    4. Measure the voltage between the high voltage battery negative ( - ) terminal and ground.
    5. Measure the voltage between the rear high voltage battery positive ( + ) and negative ( - ) terminal.
    6. Measure the voltage between the rear high voltage battery positive ( + ) terminal and ground.
    7. Measure the voltage between the rear high voltage battery negative ( - ) terminal and ground.
    1. Check for insulation breakdown via KDS and physical leakage current before working on EV.
    2. Remove the main fuse if insulation breakdown or leakage current is suspected. (Remove the main fuse even when DTC CODE ON such as PRA malfunction) (Refer to High Voltage Battery Control System - "Main Fuse") ※ If there is no insulation breakdown or leakage current and it is normal, work without removing the main fuse.

Specification ➤

Special Service Tool

Special Service Tool

Tool Name / Number Illustration Description
Ball joint puller
09568 - 2J100
Used for removal of tie rod end
Lower arm ball joint remover
0K545 - A9100
Used for removal of front lower arm ball joint

Troubleshooting

Troubleshooting

Excessive play in steering

Suspected Cause Remedy
Universal joint bolt got loose Retighten or replace if necessary
Yoke plug got loose Retighten
Steering gear box bolt got loose Retighten
Tie rod end stud got loose or worn Retighten or replace if necessary

Steering wheel does not return to its original position

Suspected Cause Remedy
Excessive turning resistance of tie rod end Replacement
Yoke plug excessively tight Adjustment
Faulty tie rod or ball joint Replacement
Steering gear box and front sub frame got loose Retighten
Steering column shaft or body grommet got worn Repair or replace
Bended rack Replacement

Rattling or chucking noise in the rack and pinion

Suspected Cause Remedy
Steering gear mounting bolts got loose Retighten
Tie rod end ball joint got loose Retighten
Tie rod or tie rod end ball joint got worn Replacement
Yoke plug got loose Retighten

Inspection

Inspection

Steering Wheel Play Inspection
  1. Align the steering wheel straight.
  2. Mark the steering wheel center (A) using masking tape or etc.
  3. Turn the steering wheel until the wheel is moved while MDPS power is 'ON', then measure the distance the steering wheel has rotated.

    Standard value : 0 - 30 mm (0 - 1.1811 in.) or less

  4. If the steering wheel play exceeds standard value, inspect the steering column, shaft, and linkages.
  5. Place the vehicle on the level surface.
  6. Measure the power when the steering wheel starts to move using a spring scale while MDPS power is 'ON'.

    Standard value : 29.4 N (3.0 kgf, 6.6 lb·ft) MAX.

  7. If the measured value exceeds standard value, inspect the steering gear box or MDPS system.
Checking Stationary Steering Effort

Steering Column Module (SCM) ➤

Steering Wheel ➤

Motor Driven Power Steering (MDPS) ➤