Motor and Reduction Gear System

12steps
~72min
3/5difficulty
010203040509.87N·mlb·ft
Tightening torque found on this page
Done 0 of 12

Contents:

Single-Use Parts

Single-Use Parts

Non-reusable parts (Single-Use Parts) Workshop manual provides “Components and Components Location” which can be used to identify “Non-reusable parts”. When repairing a vehicle, Non-reusable parts such as fasteners, gaskets, washers, clips and garnishes must be replaced. Kia Non-reusable parts are designed to be installed only once. Before working on a vehicle, check “Components and Components Location” to find the non-reusable parts in a system. ※ Symbol of Non-reusable parts
Symbol Meaning
Do not reuse the part. Replace with a new one.

※ Example of “Components and Components Location”

High Voltage System General Safety Information and Caution ➤

High Voltage Shut-off Procedures

High Voltage Shut-off Procedures

High Voltage Shut-off Procedures

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
High Voltage Component : Battery System Assembly (BSA), motor assembly, inverter assembly, high voltage junction box, power cable, etc.
  1. Check the Battery Management Unit (BMU) weld flag with the KDS. (Data Analysis → Battery Management System (BMS) → BMU Weld Flag)

    Specified value : NO

    Refer to the KDS screen for operating conditions and details.
  2. Open the front trunk (A).
  3. Open the low voltage (12 V) battery service cover (A).
  4. Turn the POWER OFF, separate the low voltage (12 V) battery ( - ) terminal (A).

    Tightening torque : 7.8 - 9,8 N·m

  5. Disconnect the service interlock connector (A).
    • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
    • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
    The service interlock connector cannot be completely removed.
  6. Remove the front under cover. (Refer to Motor and Reduction Gear System - "Front Under Cover")
  7. Remove the high voltage battery cover (A).

    Tightening torque : 7.8 - 11,8 N·m

  8. Disconnect the front high voltage junction box power cable (A).
    How to disconnect the connector
    1. Release the locking clip (A) by pulling it.
    2. Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).
  9. Remove the center floor rear under cover. (Refer to Motor and Reduction Gear System - "Rear Under Cover")
  10. Disconnect the Integrated Charge Control Unit (ICCU) connector (A).
    How to disconnect the connector
    1. Release the locking clip (A) by pulling it.
    2. Disconnect the connector while pressing the locking clip (B).
  11. Disconnect the rear high voltage junction box power cable (A).
    How to disconnect the connector
    1. Release the locking clip (A) by pulling it.
    2. Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).
  12. Measure the voltage between the high voltage power connector and high voltage battery terminal to check whether the high voltage is shut-off.
    30 V or less : Normal cut off high voltage circuit Above 30 V : Fault on high voltage circuit
    1. Measure the voltage between the high voltage power connector positive ( + ) terminal and negative ( - ) terminal.
    2. Measure the voltage between the high voltage battery positive ( + ) and negative ( - ) terminal.
    3. Measure the voltage between the high voltage battery positive ( + ) terminal and ground.
    4. Measure the voltage between the high voltage battery negative ( - ) terminal and ground.
    5. Measure the voltage between the rear high voltage battery positive ( + ) and negative ( - ) terminal.
    6. Measure the voltage between the rear high voltage battery positive ( + ) terminal and ground.
    7. Measure the voltage between the rear high voltage battery negative ( - ) terminal and ground.
    1. Check for insulation breakdown via KDS and physical leakage current before working on EV.
    2. Remove the main fuse if insulation breakdown or leakage current is suspected. (Remove the main fuse even when DTC CODE ON such as PRA malfunction) (Refer to High Voltage Battery Control System - "Main Fuse") ※ If there is no insulation breakdown or leakage current and it is normal, work without removing the main fuse.

Specification

Specification

Motor and Reduction Gear
Item Specification
70 kW (Front wheel) 160 kW (Rear wheel)
Motor Type Permanent magnet synchronous motor
(IPMSM)
Permanent magnet synchronous motor
(IPMSM)
Reduction gear ratio 10.65 10.65
Maximum power (kW) 70 160
Maximum torque (Nm) 255 350
Maximum rotational speed (rpm) 15,000 17,900
Cooling method Oil cooling Oil cooling

Oil Temperature Sensor
Item Specification
Sensor Type NTC thermistor
Operating Voltage (V) 4.75 - 5.25
Max current (mA) 100
Response time Test medium : Coolant MAX. 5 sec
Oil temperature [°C (°F)] -40 to 150 (-40 to 302)

Oil Temperature Sensor Table

Temperature [°C (°F)] Resistance (kΩ)
Minimum Normal Maximum
-40 (-40) 41.74 48.14 54.54
-30 (-22) 23.54 26.74 29.94
-20 (-4) 14.13 15.48 16.83
-10 (14) 8.393 9.308 10.223
0 (32) 5.281 5.790 6.299
10 (50) 3.422 3.714 4.007
20 (68) 2.310 2.450 2.590
30 (86) 1.554 1.658 1.762
40 (104) 1.084 1.148 1.212
50 (122) 0.7729 0.8126 0.8524
60 (140) 0.5615 0.5865 0.6115
70 (158) 0.4154 0.4311 0.4469
80 (176) 0.3122 0.3222 0.3322
90 (194) 0.2382 0.2446 0.2510
100 (212) 0.1844 0.1884 0.1924
110 (230) 0.1451 0.1471 0.1491
120 (248) 0.1139 0.1163 0.1187
130 (266) 0.0908 0.0930 0.0953
140 (284) 0.0731 0.0752 0.0773
150 (302) 0.0594 0.0614 0.0634

Tightening Torque

Tightening Torque

Front Under Cover

Item N·m kgf·m lb·ft lb·in
Front under cover bolts 7.8 - 11.8 0.8 - 1.2 5.8 - 8.7 -
Front rear under cover nuts 7.8 - 11.8 0.8 - 1.2 5.8 - 8.7 -

Front Motor and Reduction Gear Mounting

Item N·m kgf·m lb·ft lb·in
Motor mounting bracket bolt and nut 107.9 - 127.5 11.0 - 13.0 79.6 - 94.0 -
Motor mounting bracket bolts 63.7 - 83.4 6.5 - 8.5 47.0 - 61.5 -

Front Motor and Reduction Gear Assembly

Item N·m kgf·m lb·ft lb·in
Ground bolt 6.9 - 9.8 0.7 - 1.0 5.1 - 7.2 -
A/C pipe nut 8.8 - 13.7 0.9 - 1.4 6.5 - 10.1 -
Steering universal joint bolt 49.0 - 58.8 5.0 - 6.0 36.2 - 43.4 -
High voltage battery cover bolts 7.8 - 11.8 0.8 - 1.2 5.8 - 8.7 -
Stabilizer bar link nut 98.1 - 117.7 10.0 - 12.0 72.3 - 86.8 -
Front sub frame bolts and nut 107.9 - 127.5 11.0 - 13.0 79.6 - 94.0 -
Motor mounting bracket bolt and nut 107.9 - 127.5 11.0 - 13.0 79.6 - 94.0 -
Motor and reduction gear mounting bracket bolts 63.7 - 83.4 6.5 - 8.5 47.0 - 61.5 -

Rear Under Cover

Item N·m kgf·m lb·ft lb·in
Center floor rear under cover nuts 3.9 - 5.9 0.4 - 0.6 2.9 - 4.3 34.7 - 52.1
Rear cross member under cover nuts 3.9 - 5.9 0.4 - 0.6 2.9 - 4.3 34.7 - 52.1

Rear Motor and Reduction Gear Mounting

Item N·m kgf·m lb·ft lb·in
Motor mounting bracket bolts 63.7 - 83.4 6.5 - 8.5 47.0 - 61.5 -
Motor mounting bracket bolt and nut 107.9 - 127.5 11.0 - 13.0 79.6 - 94.0 -

Rear Motor and Reduction Gear Assembly

Item N·m kgf·m lb·ft lb·in
Fast charge connector service cover nut 7.8 - 11.8 0.8 - 1.2 5.8 - 8.7 -
Fast charge connector bolt 9.8 - 10.8 1.0 - 1.1 7.2 - 8.0 -
Rear wheel speed sensor wiring bracket bolt 19.6 - 29.4 2.0 - 3.0 14.5 - 21.7 -
Ground bolt 7.8 - 11.8 0.8 - 1.2 5.8 - 8.7 -
High voltage cable bracket nut 9.8 - 11.8 1.0 - 1.2 7.2 - 8.7 -
Rear bumper under cover nuts 7.8 - 11.8 0.8 - 1.2 5.8 - 8.7 -
Under cover bracket bolts 49.0 - 58.8 5.0 - 6.0 36.2 - 43.4 -
Rear cross member bolt and nut 176.5 - 196.1 18.0 - 20.0 130.2 - 144.7 -
Ground bolt 6.9 - 10.8 0.7 - 1.1 5.1 - 8.0 -
Main Wiring Protector Bolts 6.9 - 9.8 0.7 - 1.0 5.1 - 7.2 -
High voltage cable bracket bolt 7.8 - 11.8 0.8 - 1.2 5.8 - 8.7 -
Rear motor and reduction gear nut 107.9 - 127.5 11.0 - 13.0 79.6 - 94.0 -
Rear motor and reduction gear bolt 63.7 - 83.4 6.5 - 8.5 47.0 - 61.5 -
176.5 - 196.1 18.0 - 20.0 130.2 - 144.7 -

Reduction Gear Oil

Item N·m kgf·m lb·ft lb·in
Drain plug 44.1 - 58.8 4.5 - 6.0 32.5 - 43.4 -
Filler plug 44.1 - 58.8 4.5 - 6.0 32.5 - 43.4 -

SBW Actuator

Item N·m kgf·m lb·ft lb·in
Main wiring protector bolt 6.9 - 9.8 0.7 - 1.0 5.1 - 7.2 -
SBW actuator bolt 20.6 - 27.5 2.1 - 2.8 15.2 - 20.3 -

SBW Control Unit

Item N·m kgf·m lb·ft lb·in
SBW control unit nut 9.8 - 11.8 1.0 - 1.2 7.2 - 8.7 -

Oil Temperature Sensor

Item N·m kgf·m lb·ft lb·in
Oil temperature sensor bolt 9.8 - 11.8 1.0 - 1.2 7.2 - 8.7 -

Electric Oil Pump (EOP)

Item N·m kgf·m lb·ft lb·in
Electric Oil Pump (EOP) bolt 19.6 - 26.5 2.0 - 2.7 14.5 - 19.5 -

Disconnect Actuator System (DAS) Motor

Item N·m kgf·m lb·ft lb·in
Disconnect Actuator System (DAS) Motor bolts 4.9 - 5.9 0.5 - 0.6 3.6 - 4.3 43.4 - 52.1

Lubricant

Lubricant

Front motor and reduction gear [4WD]
Lubricant Capacity
Kia genuine ATF SP4M-1 3.2 - 3.3 ℓ (0.85 - 0.87 U.S gal., 3.38 - 3.49 U.S.qt., 2.81 - 2.90 Imp.qt.)

Rear motor and reduction gear [2WD, 4WD]
Lubricant Capacity
Kia genuine ATF SP4M-1 3.4 - 3.5 ℓ (0.90 - 0.92 U.S gal., 3.59 - 3.70 U.S.qt., 2.99 - 3.08 Imp.qt.)

Special Service Tool

Special Service Tool

Tool Name / Number Illustration Description
Reduction gear oil seal installer
09445 - GI100
Installation of the oil seal on the rear reduction gear case side[2WD]
Installation of the oil seal on the front reduction gear case and housing[4WD]
(Used with the handle)
Reduction gear oil seal installer
09445 - GI200
Installation of the oil seal on the rear reduction gear case side[2WD]
(Used with the handle)
Handle
09231 - H1100
Used with the oil seal installer
Engine fixture (adapter)
09200 - 4X000
Used for anchoring the motor and reducer gear when removing and installing the motor and reducer gear

Description and Operation

Description

  • Vehicle Control Unit (VCU) is the top-level controller of the vehicle that combines all the information to meet the driver's needs.
  • VCU comprehensively controls Drive motor control, Air conditioning load control, 12 V electric load power supply control, Disconnect Actuator System (DAS), and others.
Function Detail
Drive Motor Control
  • Calculate usable battery power
  • Calculate usable motor toque
  • Order motor torque considering Driver demands (APS, Brake SW, Shift lever)
A/C Load Control
  • Order the final FATC permission power by using the battery information and FATC request power data.
12 V Electric Load Power Supply Control
  • LDC operation mode is determined according to 12 V battery information and vehicle status.
Disconnect Actuator System (DAS) Motor
  • As DAS is applied to 4WD vehicles, it controls the connection or disconnection between the front wheel motor and drive shafts depending on the driving condition.
Cluster control
  • Command to indicate Drive Power, Energy Flow, Service lamp & various lamp lighting.
Distance to Empty (DTE)
  • Command to indicates usable battery energy and distance to empty based on prior drive pattern.
  • If drive path is set by using AVNT, DTE accuracy is improved by estimating the energy consumption to destination.
Booking / Remote control
  • Remote control through a smartphone linked with Kia connect
  • Reservation Function through operation time setting by driver.
Regenerative braking control
  • Calculate motor charge torque command for regenerative braking.
  • Calculate regenerative brake force.

Front Motor and Reduction Gear System ➤

Rear Motor and Reduction Gear System ➤

Motor and Reduction Gear Control System ➤