Brake System

12steps
~72min
3/5difficulty
010203040509.87N·mlb·ft
Tightening torque found on this page
Done 0 of 12

Contents:

Single-Use Parts

Single-Use Parts

Non-reusable parts (Single-Use Parts) Workshop manual provides “Components and Components Location” which can be used to identify “Non-reusable parts”. When repairing a vehicle, Non-reusable parts such as fasteners, gaskets, washers, clips and garnishes must be replaced. Kia Non-reusable parts are designed to be installed only once. Before working on a vehicle, check “Components and Components Location” to find the non-reusable parts in a system. ※ Symbol of Non-reusable parts
Symbol Meaning
Do not reuse the part. Replace with a new one.

※ Example of “Components and Components Location”

High Voltage System General Safety Information and Caution ➤

High Voltage Shut-off Procedures

High Voltage Shut-off Procedures

High Voltage Shut-off Procedures

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
High Voltage Component : Battery System Assembly (BSA), motor assembly, inverter assembly, high voltage junction box, power cable, etc.
  1. Check the Battery Management Unit (BMU) weld flag with the KDS. (Data Analysis → Battery Management System (BMS) → BMU Weld Flag)

    Specified value : NO

    Refer to the KDS screen for operating conditions and details.
  2. Open the front trunk (A).
  3. Open the low voltage (12 V) battery service cover (A).
  4. Turn the POWER OFF, separate the low voltage (12 V) battery ( - ) terminal (A).

    Tightening torque : 7.8 - 9,8 N·m

  5. Disconnect the service interlock connector (A).
    • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
    • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
    The service interlock connector cannot be completely removed.
  6. Remove the front under cover. (Refer to Motor and Reduction Gear System - "Front Under Cover")
  7. Remove the high voltage battery cover (A).

    Tightening torque : 7.8 - 11,8 N·m

  8. Disconnect the front high voltage junction box power cable (A).
    How to disconnect the connector
    1. Release the locking clip (A) by pulling it.
    2. Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).
  9. Remove the center floor rear under cover. (Refer to Motor and Reduction Gear System - "Rear Under Cover")
  10. Disconnect the Integrated Charge Control Unit (ICCU) connector (A).
    How to disconnect the connector
    1. Release the locking clip (A) by pulling it.
    2. Disconnect the connector while pressing the locking clip (B).
  11. Disconnect the rear high voltage junction box power cable (A).
    How to disconnect the connector
    1. Release the locking clip (A) by pulling it.
    2. Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).
  12. Measure the voltage between the high voltage power connector and high voltage battery terminal to check whether the high voltage is shut-off.
    30 V or less : Normal cut off high voltage circuit Above 30 V : Fault on high voltage circuit
    1. Measure the voltage between the high voltage power connector positive ( + ) terminal and negative ( - ) terminal.
    2. Measure the voltage between the high voltage battery positive ( + ) and negative ( - ) terminal.
    3. Measure the voltage between the high voltage battery positive ( + ) terminal and ground.
    4. Measure the voltage between the high voltage battery negative ( - ) terminal and ground.
    5. Measure the voltage between the rear high voltage battery positive ( + ) and negative ( - ) terminal.
    6. Measure the voltage between the rear high voltage battery positive ( + ) terminal and ground.
    7. Measure the voltage between the rear high voltage battery negative ( - ) terminal and ground.
    1. Check for insulation breakdown via KDS and physical leakage current before working on EV.
    2. Remove the main fuse if insulation breakdown or leakage current is suspected. (Remove the main fuse even when DTC CODE ON such as PRA malfunction) (Refer to High Voltage Battery Control System - "Main Fuse") ※ If there is no insulation breakdown or leakage current and it is normal, work without removing the main fuse.

Specification ➤

Special Service Tool

Special Service Tool

Tool Name / Number Illustration Description
Piston expander
09581 - 11000
Spreading the front brake caliper piston.
Rear brake piston adjuster
09580 - 0U000
Used for compressing rear caliper piston
Sensor cap remover
0K583 - R0400
Used for removal of wheel sensor cap
Sensor cap installer
09527 - AL500
Used for installing of wheel sensor cap (O.D : Φ86.6)
(Used with 09231 - 93100)
Handle
09231 - 93100
Handle
(Used with 09527 - AL500)
Air bleeding tool
0K580 - 3D100
Used for brake bleeding (regulating pressure)
(Used with 0K585 - E8100)
Air bleeding tool adaptor
0K585 - E8100
Used for brake bleeding (reservoir cap adapter)
(Used with 0K580 - 3D100)

Troubleshooting

Troubleshooting

  1. The brake system can be diagnosed quickly using the KDS (Refer to "DTC Diagnostic Guide").
    1. Self diagnosis : Checking failure and code number (DTC)
    2. Sensor data : Checking the system input/output data state
    3. Forced operation : Checking the system operation condition
    4. Additional function : Controlling other features including system option setting and zero point adjustment
The table below shows the most common defects and repair remedies in the brake system. Each number indicates the priority of the likely cause of the defects.

Brake warning lamp illuminates

Suspected Cause Correction
1. Brake fluid level sensor (not connected securely) Reconnect or replace
2. Low brake fluid level Fill and leak check
3. Parking brake (Set) Release
4. Integrated Electronic Brake (IEB) Diagnosis Trouble Code (DTC) Inspection

Lower pedal or spongy pedal

Suspected Cause Correction
1. Brake system (fluid leakage) Repair
2. Brake system (air inflow) Perform air bleeding procedure
3. Piston seal (Wear or damage) Replacement
4. Integrated Electronic Brake (IEB) Diagnosis Trouble Code (DTC) Inspection

Brake drag

Suspected Cause Correction
1. Brake pedal free separation (minimum) Adjustment
2. Pad (Crack or bent) Replacement
3. Piston (stuck) Replacement
4. Piston (frozen) Replacement
5. Anchor or return spring (malfunction) Replacement
6. Integrated Electronic Brake (IEB) Diagnosis Trouble Code (DTC) Inspection

Uneven brake

Suspected Cause Correction
1. Piston (stuck) Replacement
2. Pad (Polluted) Replacement
3. Piston (frozen) Replacement
4. Disc (scratches) Replacement
5. Pad (Crack or bent) Replacement

Heavy pedal and brake trouble

Suspected Cause Correction
1. Brake system (oil leakage) Repair
2. Brake system (air inflow) Perform air bleeding procedure
3. Pad (wear) Replacement
4. Pad (Crack or bent) Replacement
5. Pad (Polluted) Replacement
6. Pad (Slippery) Replacement
7. Disc (Dent or scratch) Replacement
8. Integrated Electronic Brake (IEB) Diagnosis Trouble Code (DTC) Inspection

Brake Noise

Suspected Cause Correction
1. Pad (Crack or bent) Replacement
2. Mounting bolt (Loose) Retighten
3. Disc (Dent or scratch) Replacement
4. Sliding pin (Wear) Replacement
5. Pad (Polluted) Cleaning
6. Pad (Slippery) Replacement
7. Anchor or Return spring (Faulty) Replacement
8. Brake pad shim (Damaged) Replacement

Poor Braking Performance (at High Speed)

Suspected Cause Correction
1. Pad (Wear) Replacement
2. Integrated Electronic Brake (IEB) Diagnosis Trouble Code (DTC) Inspection

Abnormal vibration when braking.

Suspected Cause Correction
1. Excessive free play of the brake pedal Adjustment
2. Integrated Electronic Brake (IEB) Diagnosis Trouble Code (DTC) Inspection
3. Brake caliper Replacement
4. Master cylinder cap seal Replacement
5. Damaged brake line Replacement
6. Disc juddering Perform brake judder inspection and resurface or replace the disc

Brake bleeding ➤

Brake System ➤

Parking Brake System ➤

Integrated Electronic Brake (IEB) System ➤

ESC (Electronic Stability Control) System ➤