Battery Control System (Long Range)
Electric Power Conversion System
In this manual: Battery Control System (Long Range)
56steps
~336min
4/5difficulty
Done 0 of 56
Contents:
Components and Components Location
Component
| 1. Integrated Charging Control Unit (ICCU) 2. Multi Inverter Assembly |
3. Inverter Assembly |
Description and Operation
Description
Definition- The electric power conversion system is a system that converts power (AC/DC ↔ DC/AC) according to the usage requirements, using power generated externally or within a vehicle.
- It converts the power from the vehicle's battery into power for driving the motor. The main components of a electric power conversion system include inverters and converters.
- It converts more than one of the voltage, current frequency or phrase without loss of power.
- It is a device that converts the DC power from the high-voltage battery in the vehicle into AC power for driving the motor.
- Power conversion within the inverter is achieved by the MOSFET power modules, which switch according to control signals. Single-phase power is converted into 3-phase power, supplies the drive motor to enable rotation.
- In addition to electric vehicles, hybrid vehicles also utilize power conversion to operate in electric drive mode. In this case, the reverse conversion process supplies voltage to the drive motor (reverse conversion device: a power device that converts the DC power from the high-voltage battery into AC power for use by the drive motor).
- The inverter performs all the functions of both forward and reverse conversion devices.
AC/DC Converter
- When the vehicle decelerates or brakes during operation, the drive motor acts as a generator, producing power. The generated power is then converted back into electrical energy for charge the high-voltage battery.
- The AC/DC converter is also used when charging the vehicle besides during driving. During external slow charging, the On-Board Charger (OBC) within the Integrated Charging Control Unit (ICCU) converts the AC to DC, charging the high-voltage battery with the converted voltage.
DC/DC converter within the Low Voltage DC/DC Converter (LDC)
- The Low Voltage DC/DC Converter (LDC) converts the voltage to low voltage to charge the low voltage (12 V) battery. The DC/DC converter within the LDC steps down the power supplied from the high-voltage battery to 12 V, providing power to the vehicle's auxiliary systems.
- The LDC is comprised of a switching part, a transformer part. for power conversion, and a rectifier part. In the switching part, power is converted, and then in the transformer part, the voltage is stepped down. After that in the rectifier part, the voltage is rectified, and 12 V is output to the battery.
Switching action: It is a device that converts power input from DC or AC into the desired output power through switching action.
DC/DC converter within the On-Board Charger (OBC)
- The On-Board Charger (OBC) consists of an AC/DC converter and a DC/DC converter. The AC/DC converter comprises an EMI filter and a PFC converter.
- EMI Filter : It is a filter designed to remove high-frequency noise caused by input voltage.
- PFC Converter : It is a converter used to compensate for power factor when converting AC voltage to DC.
- During battery charging, the DC/DC converter within the On-Board Charger (OBC) is converted to DC by the AC/DC converter, and the output voltage of the high-voltage battery is controlled through the DC/DC converter within the OBC.
- When the V2L connector is attached to the charging port or when AC 220V is used through the indoor V2L connector, the AC/DC converter and DC/DC converter inside the OBC perform bidirectional power conversion.
Battery (12 V) Specification
Specification
| Item | Specification |
| Type | eAGM60L-DIN |
| Capacity [20HR/5HR] (AH) | 60 / 48 |
| Cold cranking amperage (A) | 500 |
| Reserve capacity (Min) | 100 |
| Specific gravity | 1.30 - 1.32 [25 °C] |
| Voltage (V) | 12 |
Battery Size
|
||||||||||||||
Battery (12 V) Components and Components Location
Component
| 1. Low Voltage (12 V) Battery Negative ( - ) Cable 1-a. 7.8 - 9,8 N·m 2. Low Voltage (12 V) Battery Positive ( + ) Cable 2-a. 7.8 - 9,8 N·m 3. Battery Clamp 3-a. 9.8 - 13,7 N·m |
4. Low Voltage (12 V) Battery 5. Vehicle Control Unit (VCU) 5-a. 9.8 - 11,8 N·m 6. Battery Tray 6-a. 9.8 - 13,7 N·m |
Battery (12 V) Description and Operation
Description
- The low voltage (12 V) battery supplies power to electronic components excluding high voltage components.
- The high voltage of a high voltage battery is converted into a low voltage (DC 12 V) through the LDC to charge the low voltage (12 V) battery.
Battery Label Information
- Battery specifications
- AGM : Absorbent Glass Material
- CMF : Closed Maintenance Free
- MF : Maintenance Free
- Battery capacity (20 Ah)
- Terminal location
- L : battery positive ( + ) terminal on the left.
- R : battery positive ( + ) terminal on the right.
- Battery type
- BCI (Battery Council International) : Intruding terminal
- DIN (Deutsche Industric Normen) : Recessed terminal
- Cold Cranking Ampere (CCA)
CCA : The amount of current that can be supplied for 30 seconds while maintaining a voltage of more than 7.2 V at -18°C (-0.4°F). - Part number
- Reserve Capacity (RC)
RC : The amount of time that can be supplied 25 A while maintaining the minimum voltage of 10.5 V at 27 °C.
Battery (12 V) Removal and Installation - 2WD
Removal
|
- Open the front trunk (A).
- Open the service cover (A).
- Disconnect the low voltage (12 V) battery negative ( - ) terminal (A).
Tightening torque : 7.8 - 9,8 N·m
- Disconnect the service interlock connector (A).
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely. The service interlock connector cannot be completely removed. - Open the low voltage (12 V) battery positive ( + ) terminal cover (A).
- Disconnect the low voltage (12 V) battery positive ( + ) terminal (A).
Tightening torque : 7.8 - 9,8 N·m
- Remove the low voltage (12 V) battery (A) after removing the clamp (B).
Tightening torque : 9.8 - 13,7 N·m
- Remove the low voltage (12 V) battery. (Refer to low voltage (12 V) Battery - "Removal and Installation - 2WD")
- Remove the Vehicle Control Unit (VCU). (Refer to Motor & Reduction Gear System - "Vehicle Control Unit (VCU)")
- Separate the wiring (A) from the tray.
- Remove the low voltage (12 V) battery tray (A).
Tightening torque : 9.8 - 13,7 N·m
Installation
|
- Install in the reverse order of removal.
- Install the low voltage (12 V) battery and the tray to the specified torque.
- If the low voltage (12 V) battery is dropped, it may cause internal damage. (Do not reuse)
- When installing the low voltage (12 V) battery, install the clamp correctly.
- When replacing the low voltage (12 V) battery, be sure to replace it with the same specification(capacity, manufacturer, etc.) as the battery installed originally. When the different specification is installed, it may be determined that the battery performance is abnormal by the battery sensor.
Battery (12 V) Removal and Installation - 4WD
Removal
|
- Open the front trunk (A).
- Open the service cover (A).
- Disconnect the low voltage (12 V) battery negative ( - ) terminal (A).
Tightening torque : 7.8 - 9,8 N·m
- Disconnect the service interlock connector (A).
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely. The service interlock connector cannot be completely removed. - Open the low voltage (12 V) battery positive ( + ) terminal cover (A).
- Disconnect the low voltage (12 V) battery positive ( + ) terminal (A).
Tightening torque : 7.8 - 9,8 N·m
- Remove the low voltage (12 V) battery (A) after removing the clamp (B).
Tightening torque : 9.8 - 13,7 N·m
- Remove the low voltage (12 V) battery. (Refer to low voltage (12 V) Battery - "Removal and Installation - 4WD")
- Remove the Vehicle Control Unit (VCU). (Refer to Motor & Reduction Gear System - "Vehicle Control Unit (VCU)")
- Separate the wiring (A, B) from the tray.
- Remove the low voltage (12 V) battery tray (A).
Tightening torque : 9.8 - 13,7 N·m
Installation
|
- Install in the reverse order of removal.
- Install the low voltage (12 V) battery and the tray to the specified torque.
- If the low voltage (12 V) battery is dropped, it may cause internal damage. (Do not reuse)
- When installing the low voltage (12 V) battery, install the clamp correctly.
- When replacing the low voltage (12 V) battery, be sure to replace it with the same specification(capacity, manufacturer, etc.) as the battery installed originally. When the different specification is installed, it may be determined that the battery performance is abnormal by the battery sensor.
Battery Sensor Specification. Battery Sensor Components and Components Location
Battery Sensor Specification
Specification
| Item | Specification |
| Rated voltage (V) | 12 - 14 |
| Operating voltage (V) | 6 - 18 |
| Operating temperature [°C (°F)] | -40 to 105 (-40 to 221) |
| Parasitic current (uA) | Maximum 300 |
Battery Sensor Components and Components Location
Component
| 1. Battery Sensor Connector | 2. Battery Sensor 2-a. 7.8 - 9,8 N·m 2-b. 26.5 - 32 N·m |
Battery Sensor Description and Operation
Description
- The battery sensor is installed on the low voltage (12 V) battery negative ( - ) terminal and is also known as Intelligent Battery Sensor (IBS).
- The IBS continuously monitors the State of Charge (SOC) of the battery to maintain a consistent level of charge.
- It manages the battery system to ensure the battery is used under optimal conditions, predicts the timing for battery replacement, and detects faulty batteries in advance.
- It detects voltage changes supplied to the electrical actuator and monitors input and output currents of the low voltage (12 V) battery.
- If the air conditioning function is used for more than 5 minutes while driving, after powering off, 30 minutes later, the SOC of the low voltage (12 V) battery is checked. If the battery voltage over the reference value, this serves as a reference signal to provide data to the DATC to activate the after-blow function.
- It operates in the entire network (CAN) sleep state based on signals detected by IBS to perform vehicle power shutdown and prevent battery discharge by the power domain controller's internal current interruption system.
- When the low voltage (12 V) battery discharges, the signal is used to transmit the battery voltage to the Vehicle Control Unit (VCU) through the power domain controller, and after determining the possibility of charging by the VCU, the Low Voltage DC/DC Converter (LDC) conversion device charges the low voltage (12 V) battery.
Battery Sensor Removal and Installation - 2WD
Removal
|
- Disconnect the service interlock connector (A).
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely. The service interlock connector cannot be completely removed. - Remove the front trunk. (Refer to Body - "Front Trunk")
- Disconnect the low voltage (12 V) battery negative ( - ) terminal (A).
Tightening torque : 7.8 - 9,8 N·m
- Disconnect the battery sensor connector (A).
- Remove the battery sensor (A) after removing the bolt.
Tightening torque : 26.5 - 32 N·m
Installation
|
- Install in the reverse order of removal.
- Install the battery sensor to the specified torque.
- If the battery sensor is dropped, it may cause internal damage. (Do not reuse)
Battery Sensor Removal and Installation - 4WD
Removal
|
- Disconnect the service interlock connector (A).
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely. The service interlock connector cannot be completely removed. - Remove the front trunk. (Refer to Body - "Front Trunk")
- Disconnect the low voltage (12 V) battery negative ( - ) terminal (A).
Tightening torque : 7.8 - 9,8 N·m
- Disconnect the battery sensor connector (A).
- Remove the battery sensor (A) after removing the bolt.
Tightening torque : 26.5 - 32 N·m
Installation
|
- Install in the reverse order of removal.
- Install the battery sensor to the specified torque.
- If the battery sensor is dropped, it may cause internal damage. (Do not reuse)
Inverter Assembly (4WD) Specification. Inverter Assembly (4WD) Components and Components Location
Inverter Assembly (4WD) Specification
Specification
| Item | Specification |
| Input voltage (V) | 452.5 - 778.3 |
| Operating voltage (V) | 9 - 16 |
| Continuous current (A) | 75 (@20 min.) |
| Maximum ampere (A) | 190 (@15 sec.) |
Inverter Assembly (4WD) Components and Components Location
Component
| 1. High Voltage Junction Box Service Cover 1-a. 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in) 2. Front High Voltage Junction Box 2-a. 6.9 - 9,8 N·m 2-b. 6.9 - 9,8 N·m |
3. Inverter Assembly 3-a. 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in) |
Inverter Assembly (4WD) Description and Operation
Description
- The inverter assembly is installed on the front-wheel drive motor and converts DC power to AC power (variable frequency, variable voltage).
- It controls the rotational speed and torque of the motor through the power control.
- In the Power Electric (PE) system based on the E-GMP platform, the drive motor installed on the front wheel is configured with an integrated inverter and reducer.
- By the power modules within the inverter, we control to maximize both the rotation speed of the drive motor and the amount of regenerative braking charging into the high-voltage battery.
Inverter Assembly (4WD) Removal and Installation
Removal
|
- Drain the motor coolant. (Refer to Cooling System - "Motor Coolant")
- Remove the front high voltage junction box. (Refer to High Voltage Distributing System - "Front High Voltage Junction Box")
- Separate the inverter cooling quick connector hose (A).
- Remove the inverter assembly (A) after removing the bolts.
Tightening torque : 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
Installation
|
- Install in the reverse order of removal.
- Install the inverter assembly to the specified torque.
- If inverter assembly is dropped, it may cause internal damage. (Do not reuse)
- Replace the gasket (A) and check the installation before installing the inverter assembly.
- Perform the PE system leak test with the KDS. (Refer to High Voltage Distributing System - "Front High Voltage Junction Box")
- Fill the motor coolant. (Refer to Cooling System - "Coolant")
- Perform the Initialization of Automatic Resolver Offset Calibration procedures with the KDS. (S/W Management → Front Motor Control Unit (MCU) → Initialization of Automatic Resolver Offset Calibration)
Refer to the KDS screen for operating conditions and details.
Low Voltage DC/DC Converter (LDC) Description and Operation
Description
- There are the high voltage and low voltage (12 V) battery to supply and store the power related with driving an EV. The low voltage (12 V) battery that is as to power device supplied to electric devices and control units in the vehicle is required to extra charging device.
- If the battery state of charge (SOC) is detected by the battery sensor, it is input into the Vehicle Control Unit (VCU) through the power domain controller. The VCU judges the charging possibility and charges the low voltage (12 V) battery through the cooperative control Battery Management Unit (BMU) and Integrated Charge Control Unit (ICCU) by operating the IG3 relay when charging is necessary. In addition, the related control units are activated.
- If the low voltage (12 V) battery's voltage does not exceed the reference, the Low DC/DC Converter (LDC) lowers the high voltage to the voltage for charging the low voltage (12 V) battery and charges it. (High voltage DC → Low voltage DC)
- The low voltage (12 V) battery charging stops when it exceeds the reference value by operating the burst mode on LDC to improve battery efficiency.
- It has to monitoring the SOC of the low voltage (12 V) battery to control the LDC through the battery sensor. If the SOC is less than the reference value, the charging starts and maximum 90%.
- The LDC is integrated with the On-Board Charger (OBC) in the Integrated Charge Control Unit (ICCU). [The flowchart when charge the low voltage (12 V) battery by Low DC/DC Converter (LDC)]
When the low voltage (12 V) battery is not charged - When the lever is not P
- When the trunk is open
- When the SOC of a high voltage battery is less than 35%
- When the battery sensor or electric devices has trouble
Low Voltage DC/DC Converter (LDC) Troubleshooting
Troubleshooting
How to remedy when the fault code occurs
| Item | Major Fault Code | Suspected Cause | Inspection |
| Low Voltage DC/DC Converter (LDC) inspection | • Output overvoltage fault | • LDC | • Replace the Integrated Charge Control Unit (ICCU) when the same problem occurs after the vehicle restarts |
| • LDC voltage control fault | |||
| • Sensors fault - Current sensor offset calibration abnormality - Temperature sensor open circuit/short circuit/performance abnormality fault - Input / Output voltage sensor fault |
|||
| • PWM output fault | |||
| Vehicle inspection | • Output terminal path fault | • Wiring and connectors between the LDC output terminal and the high voltage junction box | • Check the LDC output circuit and cable connection condition |
| Coolant system fault | • Coolant system • Low coolant • Electric Water Pump (EWP) |
• Inspect the EWP | |
| • Input over current fault | • Low voltage (12 V) Battery discharged • 12 V electric component overload |
• Check the low voltage (12 V) battery discharge condition • Check abnormal operation or short circuit conditions of 12 V electric components |
Low Voltage DC/DC Converter (LDC) Replacement. Multi Inverter Assembly Specification
Low Voltage DC/DC Converter (LDC) Replacement
Replacement
|
| The Low Voltage DC/DC Converter (LDC) cannot be replaced individually due to included in the Integrated Charging Control Unit (ICCU). If necessary, replace the ICCU. |
- Replace the Integrated Charge Control Unit (ICCU). (Refer to High Voltage Charging System - "Integrated Charger and Converter Unit (ICCU)")
Multi Inverter Assembly Specification
Specification
| Item | Specification |
| Input voltage (V) | 452.5 - 778.3 |
| Operating voltage (V) | 9 - 16 |
| Continuous current (A) | 180 (@20 min.) |
| Maximum ampere (A) | 245 (@15 sec.) |
Multi Inverter Assembly Components and Components Location
Component
| 1. High Voltage Junction Box Service Cover 1-a. 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in) 2. Rear High Voltage Junction Box 2-a. 6.9 - 9,8 N·m 2-b. 15.7 - 24 N·m 2-c. 19.6 - 24 N·m |
3. Multi Inverter Assembly 3-a. 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in) |
Multi Inverter Assembly Description and Operation
Description
- The Power Electric (PE) system based on the E-GMP is composed of a motor, gearbox, inverter, and battery.
- Unlike conventional electric vehicles, electric cars based on the E-GMP platform connect the motor and inverter internally, reducing weight caused by cables and decrease volume through integration.
- It improves the driving distance of electric vehicles and maximizes driving efficiency.
- The multi inverter assembly is installed on the rear-wheel drive motor and converts DC power to AC power (variable frequency, variable voltage).
- In the case of driving and boost control for charging, it increases the voltage applied to the drive motor to obtain the appropriate driving force for the driving situation.
- Inside the multi inverter assembly, it is divided into Inverter 1 and 2. During driving and charging, it maintains optimal conditions for both states through different controls (high-efficiency mode and high-power mode) suitable for each situation.
The driving mode is determined by the motor system's torque or speed and the battery's available charge, but it can be changed based on the driver's acceleration intent. - High-Efficiency Mode: In typical driving situations, Inverter 1 operates to drive the vehicle at low or moderate speeds.
- High-Power Mode: Both Inverter 1 and 2 operate simultaneously to drive the vehicle in situations requiring high speed or high torque.
- By appropriately controlling inverters 1 and 2 during charging, the 800v high-voltage battery can be charged with the existing 400 V quick charger, improving efficiency in this case.
- The 400 V boosts to 800 V when quick charge.
- It is a next generation charging system for 400 V and 800 V multi-charging. In 400 V charging infrastructure, a motor and inverter are used to charge the 800 V battery and in the 800 V charging infrastructure, the battery is charged by the high voltage input from the charger.
Multi Inverter Assembly Removal and Installation
Removal
|
- Remove the rear high voltage junction box. (Refer to High Voltage Distributing System - "Rear High Voltage Junction Box")
- Separate the multi inverter cooling quick connector hoses (A).
- Disconnect the multi inverter assembly connector (A).
- Separate the wiring protector (A) from multi inverter assembly.
Tightening torque : 6.9 - 9,8 N·m
- Remove the ground cable (A) after removing the bolt from the motor.
Tightening torque : 7.8 - 9,8 N·m
- Remove the multi inverter assembly cover (A) after removing the fasteners.
- Remove the multi inverter assembly (A) after removing the bolts.
Tightening torque : 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
Installation
|
- Install in the reverse order of removal.
- Install the multi inverter assembly to the specified torque.
- If multi inverter assembly is dropped, it may cause internal damage. (Do not reuse)
- Replace the gasket (A) and check the installation before installing the multi inverter assembly.
- Perform the PE system leak test procedure before installing the multi-inverter assembly in the vehicle.
- Perform the Initialization of Automatic Resolver Offset Calibration procedures with the KDS. (S/W Management → Rear Motor Control Unit (MCU) → Initialization of Automatic Resolver Offset Calibration)
Refer to the KDS screen for operating conditions and details.
Was this page helpful?