Battery Control System (Long Range)

High Voltage Distributing System

56steps
~336min
4/5difficulty
010203040507.86N·mlb·ft
Tightening torque found on this page
Done 0 of 56

Contents:

Components and Components Location

Component

2WD

1. Front High Voltage Junction Box
1-a. 4.9 - 7,8 N·m (0.5 - 0.8 kgf·m, 3.6 - 5.8 lb·ft, 43.4 - 69.4 lb·ft)
2. High Voltage Junction Box Service Cover
2-a. 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
2-b. 6.9 - 9,8 N·m
3. Rear High Voltage Junction Box
3-a. 15.7 - 24 N·m
3-b. 17.7 - 26 N·m

4WD

1. High Voltage Junction Box Service Cover
1-a. 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
1-b. 6.9 - 9,8 N·m
2. Front High Voltage Junction Box
2-a. 6.9 - 9,8 N·m
3. High Voltage Junction Box Service Cover
3-a. 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
3-b. 6.9 - 9,8 N·m
4. Rear High Voltage Junction Box
4-a. 15.7 - 24 N·m
4-b. 17.7 - 26 N·m

Front High Voltage Junction Box Description and Operation

Description

[2WD]
  • It works as the power distributor for connecting the high voltage battery power and high voltage components (A/C compressor, PTC heater, etc.).
  • It is installed in front cross member and includes bus bar, fuse and PTC relay ( + ).
    NO System Possible Cause
    1 Battery signal -
    2 Battery PTC relay Battery Management Unit (BMU) relay control
    3 Battery PTC fuse 20 A
    4 PTC heater fuse 30 A
    5 A/C compressor fuse 30 A
[4WD]
  • It works as the power distributor to connect the high voltage battery power to front high voltage components (inverter, A/C compressor, PTC heater, etc.).
  • It is installed in front inverter assembly and includes bus bar and quick charge relay (+, -).
    NO System Possible Cause
    1 Battery PTC relay Battery Management Unit (BMU) relay control
    2 PTC heater fuse 30 A
    3 Battery PTC fuse 20 A
    4 A/C compressor fuse 30 A

Front High Voltage Junction Box Removal and Installation - 2WD

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Perform the high voltage shut off procedure. (Refer to Battery Control System (Long Range) - "High Voltage Shut-off Procedures")
  2. Remove the front trunk. (Refer to Body - "Front Trunk")
  3. Remove the low voltage (12 V) battery tray. (Refer to Electric Power Conversion System - "low voltage (12 V) Battery")
  4. Disconnect the front junction box connector (A).
  5. Disconnect the high voltage power cable (A) and battery heater connector (B).
  6. Disconnect the PTC heater connector (A).
  7. Disconnect the electric A/C compressor (A).
  8. Remove the front high voltage junction box (A) after removing the nuts.
    Tightening torque : 4.9 - 7,8 N·m (0.5 - 0.8 kgf·m, 3.6 - 5.8 lb·ft, 43.4 - 69.4 lb·ft)

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
    • Install the front high voltage junction box to the specified torque.
    • If front high voltage junction box is dropped, it may cause internal damage. (Do not reuse)

Front High Voltage Junction Box Removal and Installation - 4WD

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Perform the high voltage shut off procedure. (Refer to Battery Control System (Long Range) - "High Voltage Shut-off Procedures")
  2. Separate the power cable fastener (A) from the body frame.
  3. Remove the front trunk. (Refer to Body - "Front Trunk")
  4. Disconnect the PTC heater connector (A) and battery heater connector (B).
  5. Disconnect the high voltage junction box signal connector (A, B).
  6. Separate the wiring protector (A) after removing the bolts.

    Tightening torque : 6.9 - 9,8 N·m

  7. Remove the high voltage junction box service cover (A).
    Tightening torque : 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
  8. Remove the high voltage junction box ground bolts (A).

    Tightening torque : 6.9 - 9,8 N·m

  9. Separate the Electric A/C compressor connector (A) and fastener (B).
  10. Separate the power cable after separating the fasteners (A).
  11. Remove the front high voltage junction box (A).

    Tightening torque : 6.9 - 9,8 N·m

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Perform the PE system leak test with the KDS. (Refer to Front High Voltage Junction Box - "Air Tightness")
  2. Install in the reverse order of removal.
    • Install the front high voltage junction box to the specified torque.
    • If front high voltage junction box is dropped, it may cause internal damage. (Do not reuse)

Front High Voltage Junction Box Air Tightness Inspection

Special Service Tool

Tool Name Illustration Description
EV battery pack Inspecting for air tightness tool
GIT air tightness test equipment
Used for inspecting the air tightness of the Battery System Assembly (BSA) and PE system

Air Tightness Inspection

  • During the high voltage junction box and multi inverter assembly (or inverter assembly (4WD)) airtightness inspection, perform it after the motor, inverter, and junction box are all assembled.
  • Perform the Power Electric (PE) system leak test procedure by using the EV battery pack tool that is for inspecting the air tightness , when working on the high voltage junction box or the inverter assembly.
  • Install in the vehicle after completing the PE system leak test procedure, when working in the motor assembly.
  1. Disconnect the PTC heater connector (A) and battery heater connector (B).
  2. Install the battery heater sealing connector (P008) (A).
  3. Install the PTC heater sealing connector (P001) (A).
  4. Disconnect the high voltage junction box connector (A).
  5. Install the high voltage junction box sealing connector (P006) (A).
  6. Disconnect the electric A/C compressor (A).
  7. Install the Electric A/C compressor sealing connector (P007) (A).
  8. Remove the front rear under cover. (Refer to Motor and Reduction Gear System - "Front Under Cover")
  9. Install the sealing connector (P003) (A) in the high voltage cable.
  10. Install the pressure regulator adapters (A) in the pressure regulator.
    • Maintain the pressure by pushing the adapter with hands until starting to inspect, when installing the pressure regulator adapter.
    • Be careful not to bend the EV battery pack inspection tool hose and the pressure regulator adapter hose.
  11. Perform the PE system leak test with the KDS. (S/W Management → Motor Control Unit → PE System leak test)
    Refer to the KDS screen for operating conditions and details.
  12. Check the PE system leakage.
    Judgment standard for PE system leakage
    PASS FAIL

Power Cable Components and Components Location

Component Location

1. Power Cable [front high voltage junction box ↔ Battery System Assembly (BSA)]
3. Charger Inlet Assembly
2. Power Cable [Integrated Charging Control Unit (ICCU) ↔ BSA]

Power Cable Removal and Installation - 2WD

Remova7

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Power cable [front high voltage junction box - Battery System Assembly (BSA)]
  1. Perform the high voltage shut off procedure. (Refer to Battery Control System (Long Range) - "High Voltage Shut-off Procedures")
  2. Remove the front under cover. (Refer to Motor and Reduction Gear System - "Front Under Cover")
  3. Disconnect the power cable connector (A) on the front high voltage junction box side.
  4. Perform the high voltage shut off procedure. (Refer to Battery Control System (Long Range) - "High Voltage Shut-off Procedures")
  5. Remove the rear seat assembly. (Refer to Body - "Rear Seat Assembly")
  6. Remove the cable (A) after disconnecting the Integrated Charge Control Unit (ICCU) connector.
  7. Remove the rear under cover. (Refer to Motor and Reduction Gear System - "Rear Under Cover")
  8. Separate the cable (A) from the body by disconnecting the ICCU connector.
Power cable [rear high voltage junction box - Battery System Assembly (BSA)]

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
    If power cable is dropped, it may cause internal damage. (Do not reuse)

Power Cable Removal and Installation - 4WD

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Power cable [front high voltage junction box - Battery System Assembly (BSA)]
  1. Remove the front high voltage junction box. (Refer to High Voltage Distributing System - "Front High Voltage Junction Box")
    It cannot separate the power cable individually due to integrated with the front high voltage junction box.
  2. Perform the high voltage shut off procedure. (Refer to Battery Control System (Long Range) - "High Voltage Shut-off Procedures")
  3. Remove the rear seat assembly. (Refer to Body - "Rear Seat Assembly")
  4. Remove the cable (A) after disconnecting the Integrated Charge Control Unit (ICCU) connector.
  5. Remove the rear under cover. (Refer to Motor and Reduction Gear System - "Rear Under Cover")
  6. Separate the cable (A) from the body by disconnecting the ICCU connector.
Power cable [rear high voltage junction box - Battery System Assembly (BSA)]

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
    If power cable is dropped, it may cause internal damage. (Do not reuse)

Rear High Voltage Junction Box Description and Operation

Description

  • It works as the power distributor that connects high voltage battery power to rear high voltage components.
  • It is installed on the top of the rear wheel motor and the front of the multi-inverter assembly, and has a built-in bus bar and quick charging relays (+, -).
NO System Possible Cause
1 Quick charge relay ( + ) Battert Management Unit (BMU) relay control
2 Quick charge relay ( - )

Rear High Voltage Junction Box Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Perform the high voltage shut off procedure. (Refer to Battery Control System - "High Voltage Shut-off Procedures")
  2. Remove the rear cross member. (Refer to Motor and Reduction Gear System - "Rear Under Cover")
  3. Remove the rear high voltage junction box bolt (A).

    Tightening torque : 15.7 - 24 N·m

  4. Remove the rear motor and reduction gear assembly. (Refer to Motor and Reduction Gear System - "Rear Motor and Reduction Gear Assembly")
  5. Disconnect the rear high voltage junction box connector (A).
  6. Separate the high voltage cable (A) from the body after removing the bolts.

    Tightening torque : 15.7 - 24 N·m

  7. Remove the high voltage junction box service cover (A).
    Tightening torque : 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
  8. Remove the rear high voltage junction box and inverter bolts (A).

    Tightening torque : 6.9 - 9,8 N·m

  9. Remove the rear high voltage junction box (A) after removing the bolts and nut.
    Tightening torque Bolt : 15.7 - 24 N·m Nut : 17.7 - 26 N·m

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
    • Install the rear high voltage junction box to the specified torque.
    • If rear high voltage junction box is dropped, it may cause internal damage. (Do not reuse)