Erasing Programmed HomeLink Buttons

To erase the three programmed buttons (individual buttons cannot be erased):

Simultaneously press and hold the left and center buttons until the indicator light starts to flash (approximately 20 seconds).

Release both buttons. Do not hold for longer than 30 seconds.

HomeLink is now in learn mode and can be programmed at any time.

Reprogramming a Single HomeLink Button

To program the device to HomeLink using a previously trained HomeLink button, follow these steps:

1. Press and hold the desired HomeLink button. DO NOT release until step 4 has been completed.

2. When the indicator light starts to flash slowly (after 20 seconds), position the hand-held transmitter 2–8 cm (1 to 3 inches) from the HomeLink surface.

3. Press and hold the hand-held transmitter button (or press and "cycle" as described in "Canadian Programming").

4. The HomeLink indicator light will flash slowly at first, then quickly.

When the indicator light starts to flash quickly, release both buttons.

The previous device is now erased, and the new device can be activated by pressing the newly programmed HomeLink button.

This procedure will not affect other programmed HomeLink buttons.

Canadian Programming of Garage and Gate Openers

During programming, your hand-held transmitter may automatically stop transmitting. Continue to press and hold the HomeLink button (refer to steps 2–4 in the "Programming" section of this text) while pressing and re-pressing ("cycling") your hand-held transmitter every two seconds until the frequency signal has been learned. The indicator light will flash slowly, then quickly, a few seconds after successful training.

CAUTION

When programming a garage door or gate opener, it is recommended to disconnect the device from the power supply during the "cycling" process to prevent possible motor burnout.

Accessories

If you need additional information about the HomeLink wireless control system, products compatible with HomeLink, or to purchase other accessories such as the HomeLink® Lighting Package, contact HomeLink at 1-800-355-3515 or on the Internet at www.homelink.com.

FCC ID: NZLZTVHL3 IC: 4112A-ZTVHL3

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

WARNING

This transceiver complies with FCC and Industry Canada rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Outside Rear View Mirror

Always adjust the mirror angles before driving.

Your vehicle is equipped with both left and right outside rearview mirrors. The mirrors can be adjusted remotely using the remote mirror switch. The mirror heads can be folded back to prevent damage during an automatic car wash or when driving through a narrow street.

CAUTION

Do not scrape ice off the mirror; this may damage the glass surface. If ice prevents mirror movement, do not force the mirror to adjust. To remove ice, use de-icing spray, a sponge, or a soft cloth with very warm water.

CAUTION

If the mirror is blocked by ice, do not adjust the mirror by force. Use an approved de-icing spray (not radiator antifreeze) to release the frozen mechanism, or move the vehicle to a warm place and allow the ice to melt.

WARNING

Do not adjust or fold the outside rearview mirrors while the vehicle is moving. Doing so may result in loss of control and an accident, which may cause death, serious injury, or property damage.

Remote Control

Electric Type

The remote-controlled mirror switch is used to adjust the left and right outside rearview mirrors. To adjust either mirror, the ignition switch must be in the ACC position. Move the switch (1) to the R or L position to select the right or left side mirror, then press the appropriate side of the mirror adjustment control to move the selected mirror up, down, left, or right.

After adjustment, set the switch to the neutral (center) position to prevent unintentional adjustment.

CAUTION

• The mirrors stop moving when they reach the maximum adjustment angle, but the motor continues to run as long as the switch is pressed. Do not hold the switch longer than necessary, or the motor may be damaged.
• Do not attempt to adjust the outside rearview mirror manually. Doing so may damage the components.

Folding the Outside Rearview Mirror

Manual Type

To fold the outside rearview mirror, grasp the mirror housing and fold it toward the rear of the vehicle.

Electric Type

To fold the outside rearview mirror, press the button.

To unfold it, press the button again or press the unlock button.

CAUTION

The power outside rearview mirrors operate even when the ignition switch is in the LOCK position. However, to prevent unnecessary battery discharge, do not adjust the mirrors longer than necessary with the engine off.

CAUTION

If this is a power-folding outside rearview mirror, do not fold it manually. This may cause the motor to fail.

The outside rearview mirror can be folded by pressing the door lock button on the smart key within 4 seconds after locking the doors.

The outside rearview mirror can be unfolded by pressing the door unlock button on the smart key within 4 seconds after unlocking the doors.

Reverse Parking Aid Function (If Equipped)

When the gear selector lever is shifted to the R (Reverse) position, the outside rearview mirror (A) will tilt downward to assist reverse parking.

Depending on the position of the outside rearview mirror switch (1), the outside rearview mirror operates as follows:

Left or Right:

When the L or R switch is selected, both outside rearview mirrors will move downward.

Neutral:

When neither switch is selected, the outside rearview mirrors will not operate.

✽ NOTICE

The outside rearview mirrors will automatically return to their original position under the following conditions:

1. The engine start/stop button is turned to the ACC or OFF position.

2. The gear selector lever is shifted to any position other than R.

3. The outside rearview mirror remote control switch is not selected.