B210E starter relay
DTC Logic
DTC DETECTION LOGIC
NOTE:• If DTC B210E is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to PCS-30, "DTC Logic". • If DTC B210E is displayed with DTC B2605, first perform the trouble diagnosis for DTC B2605. Refer to SEC-90, "DTC Logic".
• When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the DTC B210E may be detected.

DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE 1. Press push-button ignition switch under the following conditions to start engine, and wait 5 seconds or more.- Selector lever: In the P position - Brake pedal: Depressed 2. Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT-III.
Is DTC detected? YES >> Go to SEC-148, "Diagnosis Procedure".
NO >> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE 2 1. Stop engine. 2. Perform DTC CONFIRMATION PROCEDURE for DTC P1650. Refer to EC-366, "DTC Logic" (MR16DDT) or EC-725, "DTC Logic" (HR16DE). 3. Turn ignition switch ON.4. Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT-III.
Is DTC detected? YES >> Refer to SEC-146, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis Procedure
1.INSPECTION STARTPerform inspection in accordance with procedure that confirms DTC.
Which procedure confirms DTC? DTC confirmation procedure 1>>GO TO 2.DTC confirmation procedure 2>>GO TO 5.
2.CHECK STARTER RELAY OUTPUT SIGNAL1. Check voltage between BCM harness connector and ground.

Is the inspection result normal? YES >> GO TO 4.
NO >> GO TO 3.
3.CHECK STARTER RELAY OUTPUT SIGNAL CIRCUIT 1. Turn ignition switch OFF. 2. Disconnect BCM connector. 3. Disconnect IPDM E/R connector.4. Check continuity between BCM harness connector and IPDM E/R harness connector.

5. Check continuity between BCM harness connector and ground.

Is the inspection result normal? YES >> Replace IPDM E/R. Refer to PCS-34, "Removal and Installation".
NO >> Repair or replace harness.
4.CHECK STARTER RELAY CIRCUIT 1. Turn ignition switch OFF. 2. Disconnect IPDM E/R connector.3. Check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal? YES >> GO TO 7.
NO >> Check harness for open or short between IPDM E/R and battery. Refer to PCS-27, "Wiring Diagram".
5.CHECK IGNITION POWER SUPLLY NO.2 SIGNAL 1. Turn ignition switch OFF. 2. Disconnect IPDM E/R connector.3. Check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal? YES >> Replace IPDM E/R. Refer to PCS-34, "Removal and Installation".
NO >> GO TO 6.
6.CHECK BCM INPUT SIGNAL CIRCUIT 1. Disconnect BCM connector.2. Check continuity between IPDM E/R harness connector and BCM harness connector.

3. Check continuity between transmission range switch harness connector and ground.

Is the inspection result normal? YES >> GO TO 7.
NO >> Repair or replace harness.
7.REPLACE BCM 1. Replace BCM. Refer to BCS-93, "Removal and Installation".2. Perform DTC CONFIRMATION PROCEDURE for DTC B210E. Refer to SEC-148, "DTC Logic".
Is the inspection result normal? YES >> INSPECTION END
NO >> Replace IPDM E/R. Refer to PCS-34, "Removal and Installation".