Engine Control System HR16DE

Fuel pump

In this manual: Engine Control System HR16DE
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~3min read

Component Function Check

1.CHECK FUEL PUMP FUNCTION 1. Turn ignition switch ON.

2. Pinch fuel feed hose with two fingers.

Fuel pressure pulsation should be felt on the fuel feed hose for 1 second after ignition switch is turned ON.

Is the inspection result normal? YES >> INSPECTION END

NO >> EC-780, "Diagnosis Procedure".

Diagnosis Procedure

Diagnosis Procedure

1.CHECK FUEL PUMP POWER SUPPLY CIRCUIT-I 1. Turn ignition switch OFF. 2. Disconnect ECM harness connector. 3. Turn ignition switch ON.

4. Check the voltage between ECM harness connector and ground.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 4.

NO >> GO TO 2.

2.CHECK FUEL PUMP POWER SUPPLY CIRCUIT-II 1. Turn ignition switch OFF. 2. Disconnect IPDM E/R harness connector.

3. Check the continuity between IPDM E/R harness connector and ECM harness connector.

4. Also check harness for short to ground and short to power.

4. Also check harness for short to ground and short to power.

Is the inspection result normal? YES >> GO TO 10.

NO >> GO TO 3.

3.DETECT MALFUNCTIONING PART

Check the following.

• Harness or connectors E8, F1 • IPDM E/R connector E13 • Harness for open or short to ground and short power

>> Repair open circuit or short to ground or short to power in harness or connectors.

4.CHECK FUEL PUMP POWER SUPPLY CIRCUIT-III 1. Turn ignition switch OFF. 2. Reconnect all harness connectors disconnected. 3. Disconnect “fuel level sensor unit and fuel pump” harness connector. 4. Turn ignition switch ON.

5. Check voltage between “fuel level sensor unit and fuel pump” harness connector and ground.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 8.

NO >> GO TO 5.

5.CHECK 15 A FUSE 1. Turn ignition switch OFF. 2. Disconnect 15 A fuse (No. 60) from IPDM E/R.

3. Check 15 A fuse.

Is the inspection result normal? YES >> GO TO 6.

NO >> Replace fuse.

6.CHECK FUEL PUMP POWER SUPPLY CIRCUIT-IV 1. Disconnect IPDM E/R harness connector.

2. Check the continuity between IPDM E/R harness connector and “fuel level sensor unit and fuel pump” harness connector.

3. Also check harness for short to ground and short to power.

3. Also check harness for short to ground and short to power.

Is the inspection result normal? YES >> GO TO 10.

NO >> GO TO 7.

7.DETECT MALFUNCTIONING PART

Check the following.

• Harness connectors E105, M77 • Harness connectors B1, M18 • Harness for open or short between IPDM E/R and “fuel level sensor unit and fuel pump”

>> Repair open circuit or short to ground or short to power in harness or connectors.

8.CHECK FUEL PUMP GROUND CIRCUIT

1. Check the continuity between “fuel level sensor unit and fuel pump” and ground.

2. Also check harness for short to power.

2. Also check harness for short to power.

Is the inspection result normal? YES >> GO TO 9.

NO >> Repair open circuit or short to power in harness or connectors.

9.CHECK FUEL PUMP

Refer to EC-782, "Component Inspection".

Is the inspection result normal? YES >> GO TO 10.

NO >> Replace “fuel level sensor unit and fuel pump”.

10.CHECK INTERMITTENT INCIDENT

Refer to GI-42, "Intermittent Incident".

Is the inspection result normal? YES >> Replace IPDM E/R.

NO >> Repair or replace harness or connectors.

Component Inspection

1.CHECK FUEL PUMP 1. Turn ignition switch OFF. 2. Disconnect “fuel level sensor unit and fuel pump” harness connector.

3. Check resistance between “fuel level sensor unit and fuel pump” terminals as follows.

Is the inspection result normal?

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace “fuel level sensor unit and fuel pump”.