Supplemental Restraint Systems

The SRS warning light remains on.

~9min read

DESCRIPTION

The SRS warning light is located in the combination meter assembly.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds when the engine switch is turned from OFF to ON, and then goes off automatically.

If the SRS system malfunctions, the SRS warning light comes on to inform the driver that there is a problem.

If a malfunction occurs in the airbag sensor assembly, the instrument cluster assembly, or the wire harness connected to the airbag sensor assembly or instrument cluster assembly, the SRS warning light comes on.

When the TC and CG terminals of the DLC3 are connected, DTCs are indicated by the SRS warning light flashing.

The SRS is equipped with a voltage boost circuit (DC-DC converter) built into the airbag sensor assembly, which operates when the power supply voltage drops.

When the battery voltage drops, the voltage boost circuit (DC-DC converter) operates to increase the SRS system voltage to a normal level. In addition, when the voltage drops, the SRS warning light comes on.

A malfunction that occurs in this circuit is not stored in the airbag sensor assembly. The SRS warning light turns off automatically once the power supply voltage returns to a normal level.

The SRS warning light activation signal is transmitted from the airbag sensor assembly to the instrument cluster assembly via the CAN communication system.

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • After turning the ignition switch OFF, a waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, be sure to read the precautions for disconnecting the cable from the negative (-) battery terminal before performing the work.

    Click here

  • Check the fuses for the circuits related to this system before performing the following procedure.
  • When replacing the instrument cluster assembly, always use a new part. If an instrument cluster assembly that was installed in another vehicle is used, the stored information will not match the information transmitted by the vehicle, and a DTC may be stored.

PROCEDURE

  1. CHECK SRS WARNING LIGHT OPERATION

(a) Turn the ignition switch to ON, and check the SRS warning light condition.

HINT:

The initial check lasts approximately 6 seconds after the ignition switch is turned to ON.

Result:

Result

Proceed to

After the initial check period, the SRS warning light remains on.

A

After the initial check period, the SRS warning light turns off and then comes on again.

B

B

GO TO STEP 6

A
  1. CHECK BATTERY VOLTAGE

(a) Measure the battery voltage.

Standard voltage:

11 à 14 V

NG

CHECK CHARGING SYSTEM AND BATTERY

OK
  1. CHECK CONNECTOR

(a) Turn the ignition switch OFF.

(b) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Check that the connector is properly connected to the airbag sensor.

OK:

The connector is properly connected.

HINT:

If the connector is not properly connected, reconnect it and proceed to the next check.

(d) Disconnect the connector from the airbag sensor assembly.

(e) Check that the connector terminals are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

NG

REPLACE WIRE HARNESS

OK
  1. CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND)

(a) Connect the cable to the negative (-) battery terminal.

*a

Front view of wire harness side connector

(to airbag sensor assembly)

(b) Turn the ignition switch to ON.

(c) Operate all electrical components (rear window defogger, windshield wipers, headlights, heater blower, etc.).

(d) Measure the voltage according to the value(s) specified in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

F70-21 (IG2) - Body Ground

Ignition Switch in ON position

8 à 16 V

(e) Turn the ignition switch to OFF.

(f) Measure the resistance according to the value(s) shown in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F70-25 (E1) - Body Ground

Always

Below 1 Ω

F70-26 (E2) - Body Ground

Always

Below 1 Ω

NG

REPLACE WIRE HARNESS

OK
  1. CHECK SRS WARNING LIGHT

(a) Turn the ignition switch to ON, and check the SRS warning light condition.

OK:

After the initial check period, the SRS warning light turns off for approximately 10 seconds and then comes on again.

HINT:

The initial check period lasts approximately 6 seconds after the ignition switch is turned to ON.

OK

REPLACE AIRBAG SENSOR ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

  1. INSPECT CAN COMMUNICATION SYSTEM

(a) Using the Techstream, check whether the CAN communication system operates normally.

OK:

The CAN communication system operates normally.

HINT:

Refer to the CAN Bus Check section in the CAN communication system.

Click here

NG

GO TO CAN COMMUNICATION SYSTEM

OK
  1. CHECK BATTERY VOLTAGE

(a) Measure the battery voltage.

Standard voltage:

11 à 14 V

NG

CHECK CHARGING SYSTEM AND BATTERY

OK
  1. CHECK CONNECTOR

(a) Turn the ignition switch OFF.

(b) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Check that the connector is properly connected to the airbag sensor.

OK:

The connector is properly connected.

HINT:

If the connector is not properly connected, reconnect it and proceed to the next check.

(d) Disconnect the connector from the airbag sensor assembly.

(e) Check that the connector terminals are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

NG

REPLACE WIRE HARNESS

OK
  1. CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND)

(a) Connect the cable to the negative (-) battery terminal.

*a

Front view of wire harness side connector

(to airbag sensor assembly)

(b) Turn the ignition switch to ON.

(c) Operate all electrical components (rear window defogger, windshield wipers, headlights, heater blower, etc.).

(d) Measure the voltage according to the value(s) specified in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

F70-21 (IG2) - Body Ground

Ignition Switch in ON position

8 à 16 V

(e) Turn the ignition switch to OFF.

(f) Measure the resistance according to the value(s) shown in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F70-25 (E1) - Body Ground

Always

Below 1 Ω

F70-26 (E2) - Body Ground

Always

Below 1 Ω

NG

REPLACE WIRE HARNESS

OK
  1. CHECK CONNECTOR

(a) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(b) Check that the connector is properly connected to the instrument cluster assembly.

OK:

The connector is properly connected.

HINT:

If the connector is not properly connected, reconnect it and proceed to the next check.

(c) Disconnect the connector from the instrument cluster assembly.

(d) Check that the connector terminals are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

NG

REPAIR OR REPLACE CONNECTOR

OK
  1. CHECK WIRE HARNESS (INSTRUMENT CLUSTER ASSEMBLY - BODY GROUND)

(a) Connect the cable to the negative (-) battery terminal.

*a

Front view of wire harness side connector

(to instrument cluster assembly)

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

F4-39 (IG+) - Body Ground

Ignition Switch in ON position

11 à 14 V

F4-40 (B) - Body Ground

Ignition Switch in OFF position

11 à 14 V

(d) Turn the ignition switch to OFF.

(e) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F4-21 (ET) - Body Ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE WIRE HARNESS

OK
  1. CHECK SRS WARNING LIGHT

(a) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(b) Connect the connector to the instrument cluster assembly.

(c) Connect the cable to the negative (-) battery terminal.

(d) Turn the ignition switch to ON, and check the SRS warning light condition.

OK:

After the initial check period, the SRS warning light turns off for approximately 10 seconds and then comes on again.

HINT:

The initial check period lasts approximately 6 seconds after the ignition switch is turned to ON.

OK

REPLACE AIRBAG SENSOR ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY