Supplemental Restraint Systems

Vehicle Control History

~53min read
0102030405012.59N·mlb·ft
Tightening torque found on this page

VEHICLE CONTROL HISTORY

Function Overview

(a) The vehicle control history is a function that records control data (data recording) when triggered by a specific vehicle behavior. When no DTC is detected based on information provided by the customer, the vehicle control history can be checked to obtain quantitative diagnostic information, and it can be used as a reference for diagnosing malfunctions.

(b) The vehicle control history is stored in various memory areas designated by trigger groups, and up to 140 items can be recorded in total. If storage space runs out, the oldest data is erased first to make room, and new data is recorded.

(c) Each trigger receives time information from the main body ECU (elapsed time after the ignition switch is turned ON) or from the navigation system* (absolute time).

  • *: Only for factory-installed navigation systems (factory option)

(d) The data is stored in the airbag sensor assembly EEPROM. Even if the negative (-) battery terminal is disconnected, the vehicle control history is not erased. In addition, the data cannot be erased using the Techstream.

Precautions for Use

(a) The vehicle control history is used as an information source during malfunction diagnosis for each system and cannot be used to determine the actual cause of a problem.

(b) The estimate of each trigger is based on signals transmitted by sensors and actuators (recognition value of each ECU). Therefore, be sure to check and adjust the systems related to each trigger when using the vehicle control history.

Basic Flow Rate

Trigger Item

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Using the Techstream, select the following menus: Body Electrical / SRS Airbag / Utility / Vehicle Control History.

Body Electrical > SRS Airbag > Utility

Vehicle Control History

Trigger Items Table

Related System

Storage Area Group (Storage Limit)

Trigger Item Name

Trigger Description

Remarks

Engine Control / Hybrid Control / Automatic Transmission

Area 2

(approx. 42 times)

Accelerator pedal opening angle signal is high at low speed

A high accelerator position signal condition continues for a certain period of time when driving at low speed.

-

Accelerator pedal opening angle signal is high immediately after the brake pedal is released.

A high accelerator position signal is received during low-speed driving after switching from the brake input condition to the accelerator pedal released condition.

-

Area 7

(approx. 12 times)

High accelerator position at medium to high speed

A high accelerator position signal condition continues for a certain period of time when driving at medium to high speed.

-

Engine Control / Hybrid Control / Automatic Transmission

Area 3

(approx. 40 times)

Accelerator pedal opening angle signal indicates medium or high immediately after shifting to R.

A medium to high accelerator position signal is received during low-speed driving immediately after the shift lever is moved to R while a low accelerator position signal condition exists.

Except hybrid vehicles

Accelerator pedal opening angle signal indicates medium or high immediately after shifting to forward drive.

A medium to high accelerator position signal is received during low-speed driving immediately after the shift lever is moved to a forward drive position (a position other than P, N or R) while a low accelerator position signal condition exists.

Except hybrid vehicles

Accelerator pedal opening angle signal indicates medium or high immediately after shifting to D.

A medium to high accelerator position signal is received during low-speed driving immediately after the shift lever is moved to D (a position other than P or N) while a low accelerator position signal condition exists.

Hybrid vehicles only

R position signal input during medium or high accelerator signal input

A medium to high accelerator position signal condition continues for a certain period of time while the shift lever is in R after the shift lever is moved to R during a medium to high accelerator position signal condition.

Except hybrid vehicles

Forward drive position signal input during medium or high accelerator signal input

A medium to high accelerator position signal condition continues for a certain period of time in a forward drive position (a position other than P, N or R) after shifting to a forward drive position (a position other than P, N or R) during a medium to high accelerator position signal condition.

Except hybrid vehicles

Engine Control / Hybrid Control / Automatic Transmission

Area 3

(approx. 40 times)

D position signal input during medium or high accelerator signal input

The shift lever is moved to D (a position other than P or N) during a medium to high accelerator position signal condition.

Hybrid vehicles only

Simultaneous accelerator signal and brake signal input

A medium to high accelerator position signal condition and a brake input condition continue simultaneously for a certain period of time.

-

Medium or high accelerator signal input immediately after shifting to D or R.

The shift lever is moved to D (or R) while a low accelerator position signal condition exists after the shift lever was moved to R (or D). Then, a medium to high accelerator position signal is received.

-

Medium or high accelerator signal input while the shift lever is in N.

A medium to high accelerator position signal is received during low-speed driving after the shift lever is moved to N.

-

Brake Control

Area 5

(approx. 5 times)

VSC Operation History

When VSC operation starts.

For vehicles with VSC only

Traction Control Operation History

When traction control operation starts.

For vehicles with TRC only

ABS Operation History

When ABS operation starts.

-

Area 1

(approx. 4 times)

Sudden braking history

Detects forward and rearward acceleration above a certain level.

For vehicles with VSC only

Sudden swerving history

Detects lateral acceleration above a certain level.

For vehicles with VSC only

Cruise control

Zone 4

(approx. 15 times)

Accelerator pedal opening angle signal is high while cruise control is operating

A high accelerator position signal condition continues for a certain time during cruise control operation.

Only for vehicles with cruise control

Pre-collision safety

Zone 6

(approx. 6 times)

Electrical control system operation history (buzzer operation)

Pre-collision safety (buzzer) operates.

Only for vehicles with PCS

Electrical control system operation history (warning brake operation)

Pre-collision safety (warning brake) operates.

Only for vehicles equipped with pre-collision safety (with driver monitor camera)

Electrical control system operation history (pre-collision brake assist operation)

PCS (PCS brake assist) operates.

Only for vehicles with PCS

Electrical control system operation history (preliminary braking operation)

Pre-collision safety (preliminary braking) operates.

Only for vehicles with PCS

Electrical control system operation history (pre-collision braking operation)

PCS (PCS braking) operates.

Only for vehicles with PCS

Electrical control system operation history (pre-collision seat belt operation)

PCS (pre-collision seat belt) operates.

Only for vehicles with PCS

PCS operation history (pre-pump operation)

PCS (PCS brake assist standby) operates.

Only for vehicles with PCS

PCS operation history (PBR operation)

PCS (brake light illumination) operates.

Only for vehicles with PCS

PCS operation history (PBH operation)

PCS (after brake hold operation) operates.

Only for vehicles with PCS

PCS operation history (collision avoidance assist)

PCS (evasive assist) operates.

Only for vehicles with PCS

Electrical control system operation history (when acceleration above a certain level is detected)

Forward and rearward acceleration above a certain threshold is detected.

Only for vehicles with PCS

Lane keeping assist / lane departure warning

Zone 8

(approx. 6 times)

A torque sensor signal above a certain level is detected during lane keeping assist / lane departure warning operation.

When the LKA/LDA system is ON, a torque sensor signal above a certain threshold is detected.

Only for vehicles equipped with LKA/LDA (with steering control)

Distance detection sonar system

Zone 9

(approx. 6 times)

ICS operation history (output limit)

ICS (output restriction) operates.

Only for vehicles with ICS

ICS operation history (maximum output limit)

ICS (maximum output restriction) operates.

Only for vehicles with ICS

ICS operation history (brake control)

ICS (brake control) operates.

Only for vehicles with ICS

ICS operation history (stop)

ICS (vehicle stop) operates.

Only for vehicles with ICS

ICS operation history (reverse)

ICS (reverse) operates.

Only for vehicles with ICS

ICS operation history (temporarily unavailable)

ICS temporarily unavailable.

Only for vehicles with ICS

Recorded data items

(a) When a trigger is detected, the vehicle states (ECU data) before and after the trigger are recorded as recorded data.

(b) The recording time and recorded data differ for each trigger.

If there is no PCS/ICS operation history

If there is PCS/ICS operation history

Recording Data Specifications

Trigger Item

Recorded data

Before detection

After detection

Sampling cycle (s)

ID No.

Item

Recording time (s)

Number of points

Recording time (s)

Number of points

2

Accelerator pedal opening angle signal is high at low speed

7,5

15

7,5

16

0,5

3

High accelerator position at medium to high speed

7,5

15

7,5

16

0,5

4

Accelerator pedal opening angle signal is high immediately after the brake pedal is released.

7,5

15

7,5

16

0,5

5-1

Accelerator pedal opening angle signal indicates medium or high immediately after shifting to R.

5

10

5

11

0,5

5-2

Accelerator pedal opening angle signal indicates medium or high immediately after shifting to forward drive.

5-3

Accelerator pedal opening angle signal indicates medium or high immediately after shifting to D.

6-1

R position signal input during medium or high accelerator signal input

5

10

5

11

0,5

6-2

Forward drive position signal input during medium or high accelerator signal input

6-3

D position signal input during medium or high accelerator signal input

8

Simultaneous accelerator signal and brake signal input

5

10

5

11

0,5

9

Medium or high accelerator signal input immediately after shifting to D or R.

5

10

5

11

0,5

10

Medium or high accelerator signal input while the shift lever is in N.

5

10

5

11

0,5

12

VSC Operation History

5

34

5

35

0,15

13

Traction Control Operation History

5

34

5

35

0,15

14

ABS Operation History

5

34

5

35

0,15

15

Sudden braking history

5

34

5

35

0,15

16

Sudden swerving history

5

34

5

35

0,15

17

Accelerator pedal opening angle signal is high while cruise control is operating

5

10

5

11

0,5

18-1

Electrical control system operation history (buzzer operation)

5

10

4

9

0,5

18-2

Electrical control system operation history (warning brake operation)

18-3

Electrical control system operation history (pre-collision brake assist operation)

18-4

Electrical control system operation history (preliminary braking operation)

18-5

Electrical control system operation history (pre-collision braking operation)

18-6

Electrical control system operation history (pre-collision seat belt operation)

18-7

PCS operation history (pre-pump operation)

18-8

PCS operation history (PBR operation)

18-9

PCS operation history (PBH operation)

18-10

PCS operation history (collision avoidance assist)

18-11

Electrical control system operation history (when acceleration above a certain level is detected)

19

A torque sensor signal above a certain level is detected during lane keeping assist / lane departure warning operation.

8

40

0

1

0,2

20-1

ICS operation history (output limit)

5

10

5

11

0,5

20-2

ICS operation history (maximum output limit)

20-3

ICS operation history (brake control)

20-4

ICS operation history (stop)

20-5

ICS operation history (reverse)

20-6

ICS operation history (temporarily unavailable)

Recording Data Table

Item name

Trigger ID No.

Vehicle speed

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11, 19, 20-1, 20-2, 20-3, 20-4, 20-5, 20-6

Accelerator opening rate

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11, 19, 20-1, 20-2, 20-3, 20-4, 20-5, 20-6

Engine speed data

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11, 19, 20-1, 20-2, 20-3, 20-4, 20-5, 20-6

Cruise control

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11, 19, 20-1, 20-2, 20-3, 20-4, 20-5, 20-6

Engaged Gear Position Signal

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11, 19, 20-1, 20-2, 20-3, 20-4, 20-5, 20-6

Brake switch

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11, 19, 20-1, 20-2, 20-3, 20-4, 20-5, 20-6

Brake fluid pressure

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11, 19, 20-1, 20-2, 20-3, 20-4, 20-5, 20-6

Yaw rate sensor signal

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11, 19, 20-1, 20-2, 20-3, 20-4, 20-5, 20-6

Longitudinal deceleration sensor signal

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11, 19, 20-1, 20-2, 20-3, 20-4, 20-5, 20-6

Lateral deceleration sensor signal

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11, 19, 20-1, 20-2, 20-3, 20-4, 20-5, 20-6

Throttle opening rate

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11, 19, 20-1, 20-2, 20-3, 20-4, 20-5, 20-6

Fuel injection quantity command value

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11, 19, 20-1, 20-2, 20-3, 20-4, 20-5, 20-6

Power steering signal

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11, 19, 20-1, 20-2, 20-3, 20-4, 20-5, 20-6

Invalid ICS data received signal

20-1, 20-2, 20-3, 20-4, 20-5, 20-6

ICS flag trigger

20-1, 20-2, 20-3, 20-4, 20-5, 20-6

ICS temporarily unavailable (dirt)

20-1, 20-2, 20-3, 20-4, 20-5, 20-6

ICS temporarily unavailable (low voltage)

20-1, 20-2, 20-3, 20-4, 20-5, 20-6

ICS drive power control request signal

20-1, 20-2, 20-3, 20-4, 20-5, 20-6

ICS brake control request signal

20-1, 20-2, 20-3, 20-4, 20-5, 20-6

ICS controlled object distance

20-1, 20-2, 20-3, 20-4, 20-5, 20-6

ICS controlled object 1 position (X)

20-1, 20-2, 20-3, 20-4, 20-5, 20-6

ICS controlled object 1 position (Y)

20-1, 20-2, 20-3, 20-4, 20-5, 20-6

ICS recognition sensor (controlled object 1)

20-1, 20-2, 20-3, 20-4, 20-5, 20-6

ICS recognition level (controlled object 1)

20-1, 20-2, 20-3, 20-4, 20-5, 20-6

ICS controlled object 2 position (X)

20-1, 20-2, 20-3, 20-4, 20-5, 20-6

ICS controlled object 2 position (Y)

20-1, 20-2, 20-3, 20-4, 20-5, 20-6

ICS recognition sensor (controlled object 2)

20-1, 20-2, 20-3, 20-4, 20-5, 20-6

ICS recognition level (controlled object 2)

20-1, 20-2, 20-3, 20-4, 20-5, 20-6

ICS controlled object 3 position (X)

20-1, 20-2, 20-3, 20-4, 20-5, 20-6

ICS controlled object 3 position (Y)

20-1, 20-2, 20-3, 20-4, 20-5, 20-6

ICS recognition sensor (controlled object 3)

20-1, 20-2, 20-3, 20-4, 20-5, 20-6

ICS recognition level (controlled object 3)

20-1, 20-2, 20-3, 20-4, 20-5, 20-6

Power Train Mode

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 15, 16

SNOW Mode

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 15, 16

Driving mode correct/incorrect

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 15, 16

VSC OFF light

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 15, 16

TRC OFF light

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 15, 16

TRC/VSC OFF light correct/incorrect

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 15, 16

EV Mode

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 15, 16

EV Mode correct/incorrect

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 15, 16

Shift gear

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 15, 16

Engine load factor

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10

READY signal

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 15, 16

Engaged Gear Position Signal

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 15, 16

Turbine speed/input shaft speed

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 15, 16

Under VSC control

12, 13, 14, 15, 16

Under ABS control

12, 13, 14, 15, 16

Under VDM control

12, 13, 14, 15, 16

TRC operation indicator

12, 13, 14, 15, 16

Front right wheel speed

12, 13, 14, 15, 16

Front left wheel speed

12, 13, 14, 15, 16

Rear right wheel speed

12, 13, 14, 15, 16

Rear left wheel speed

12, 13, 14, 15, 16

Cruise Control System

17

Drive power request estimate indicator

17

Cruise control main switch indicator

17

DSS estimate indicator

17

Cruise control Res/Accel switch

17

Cruise control Set/Coast switch

17

Cruise control cancel switch

17

Cruise control brake switch

17

Cruise control D signal

17

Cruise control main switch

17

Cruise control set speed

17

Vehicle speed (with cruise control)

17

Cruise control request value

17

ACC target distance

17

ACC target condition

17

ACC relative speed

17

Pre-collision safety received data incorrect indicator

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

ALM request indicator 2

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

ALM request signal

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

ABK request signal

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

PBA request signal

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

FPB request signal

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

PB request signal

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

PSB request signal

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

Pre-fill request signal

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

Stop light activation request signal

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

PCS brake hold request signal

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

Collision avoidance assist request signal 1

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

Collision avoidance assist request signal 2

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

Collision avoidance assist request signal 3

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

PCS SW

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

PCS display (Diag status)

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

PCS display (millimeter wave dirt presence)

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

PCS display (temporarily unavailable)

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

PCS display (recognition sensor status)

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

PCS display (millimeter wave radar low voltage status)

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

PCS display (camera backlight status)

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

PCS display (millimeter wave radar alignment indicator)

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

PCS display (object recognition status)

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

PCS display (control status 1)

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

PCS display (control status 2)

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

Target distance

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

Target relative speed

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

Target lateral position

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

Target Object Number

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

Relative Acceleration for Target Control

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

Collision 1 Duration for Target Control

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

Collision 2 Duration for Target Control

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

Collision State Duration for Target Control

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

Recognition Sensor Status for Target Control

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

Object Type for Target Control

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

PCS ALM Mode Status

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

PCS ALM Status

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

PCS Protection Status C

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

PCS Protection Status B

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

PCS Protection Status A

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

Recognition Sensor Status (Millimeter-Wave Radar Horizontal Axis Offset Status)

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

Recognition Sensor Status (Millimeter-Wave Radar Vertical Axis Offset Status)

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

Estimated Curve Angle

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

Detection of Certain Acceleration Level

18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11

LKA DDR Trigger Signal

19

Incorrect LKA DDR Data

19

Steering Wheel Unlock Condition

19

LKA Steering Operation

19

LDA Steering Operation

19

LKA Control Condition (EPS Control)

19

LKA Control Condition

19

Turn Signal Operation

19

EPS Torque Sensor Value

12, 13, 14, 15, 16, 19

HV Recognition Indicator

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11, 19, 20-1, 20-2, 20-3, 20-4, 20-5, 20-6

Diesel Indicator

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11, 19, 20-1, 20-2, 20-3, 20-4, 20-5, 20-6

Sensor Type Identification (Yaw Rate Sensor)

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11, 19, 20-1, 20-2, 20-3, 20-4, 20-5, 20-6

Sensor Type Identification (Deceleration Sensor)

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11, 19, 20-1, 20-2, 20-3, 20-4, 20-5, 20-6

Sensor Type Identification (Deceleration Sensor Location)

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11, 19, 20-1, 20-2, 20-3, 20-4, 20-5, 20-6

Sensor Type Identification (Safety)

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11, 19, 20-1, 20-2, 20-3, 20-4, 20-5, 20-6

Yaw Rate Sensor Replacement Information

2, 4, 3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18-1, 18-2, 18-3, 18-4, 18-5, 18-6, 18-7, 18-8, 18-9, 18-10, 18-11, 19, 20-1, 20-2, 20-3, 20-4, 20-5, 20-6

DSC Operation Indicator

5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 8, 9, 10

Recording Data Items Table

Tester display

Item

Range

Diagnostic Note

Vehicle Speed

Vehicle Speed (Driven Wheels)

0 à 200 km/h

If the vehicle speed is 200 km/h or higher, "200 km/h" is displayed.

Accelerator Opening Ratio

Accelerator Pedal Opening Angle

0,0 à 100,0 %

-

Engine RPM Data

Crankshaft Revolutions per Minute

0 to 12,800 rpm

-

Cruise Control

Cruise Control Status

ON: Cruise control is operating

OFF: Cruise control is not operating or is not installed

If the vehicle is not equipped with cruise control, OFF is displayed.

Shift Position Signal

Shift lever position

N / D / R / P / 5 / 4 / 3 / 2 / LO / B / SD / S-Mode / Undetermined

-

Brake SW

Brake Light Switch Position

ON: The brake lights illuminate

OFF: The brake lights do not illuminate

-

Brake Oil Pressure

Brake fluid pressure inside the brake master cylinder

0.000 to 12.144 MPa

-

Yaw Rate Sensor Signal

Angular velocity of the vehicle when cornering

-61.000 to 61.000 deg/s

  • A positive value is displayed when turning left.
  • If the value is 61 deg/s or higher, "61.000 deg/s" is displayed.
  • If the value is -61 deg/s or lower, "-61.000 deg/s" is displayed.

Longitudinal G Sensor Signal

Longitudinal acceleration measured by the acceleration sensor for the VSC system

-8,97250 à 8,97250 m/s2

  • A positive value is displayed when acceleration increases.
  • If the value is 8.9725 m/s² or higher, "8.97250 m/s²" is displayed.
  • If the value is -8.9725 m/s² or lower, "-8.97250 m/s²" is displayed.

Lateral G Sensor Signal

Lateral acceleration measured by the acceleration sensor for the VSC system

-8,97250 à 8,97250 m/s2

  • A positive value is displayed when turning left.
  • If the value is 8.9725 m/s² or higher, "8.97250 m/s²" is displayed.
  • If the value is -8.9725 m/s² or lower, "-8.97250 m/s²" is displayed.

Throttle Opening Ratio

Throttle Valve Opening Ratio

0,0 à 100,0 %

"Invalid" is displayed for vehicles other than gasoline vehicles.

Command Value of Fuel Injection Amount

Commanded Fuel Injection Volume

0.0 to 120.0 mm³/st

  • "Invalid" is displayed for vehicles other than diesel vehicles.
  • If the value is 120 mm³/st or higher, "120.0 mm³/st" is displayed.

Steering Signal

Steering angle

-567.0 to 567.0 deg.

  • A positive value is displayed when the steering wheel is turned to the left.
  • If the value is 567 deg. or higher, "567.0 deg." is displayed.
  • If the value is -567 deg. or lower, "-567.0 deg." is displayed.
  • Since the steering wheel must be turned for the steering angle sensor to obtain an initial value, if the steering wheel is not operated after the ignition switch is set to ON, an invalid value will be displayed.

ICS Received Data Invalid Flag

ICS data existence

Valid / Invalid

-

ICS Trigger Flag

ICS trigger condition existence (triggers ID 20-1, 20-2, 20-3, 20-4, 20-5, 20-6)

OFF / Output Limit / Max Output Limit / Brake Control / Stop / Regression / Temporarily Not Available

  • If the ICS has not operated, "OFF" is displayed.
  • If the "ICS Received Data Invalid Flag" value is "Invalid", this item will not be valid.

ICS Temporarily Not Available (Dirt)

ICS temporarily unavailable (dirt, etc. on the sensor)

Available / Not Available

If the "ICS Received Data Invalid Flag" value is "Invalid", this item will not be valid.

ICS Temporarily Not Available (Low Voltage)

ICS temporarily unavailable (sensor voltage)

Available / Not Available

If the "ICS Received Data Invalid Flag" value is "Invalid", this item will not be valid.

ICS Request Driving Force Control Flag

Driving force suppression control operation

ON / OFF

If the "ICS Received Data Invalid Flag" value is "Invalid", this item will not be valid.

ICS Request Braking Control Flag

Brake control system operation

ON / OFF

If the "ICS Received Data Invalid Flag" value is "Invalid", this item will not be valid.

ICS Controlled Object Distance

Detected object distance

0,00 à 3,78 m

If the "ICS Received Data Invalid Flag" value is "Invalid", this item will not be valid.

ICS Controlled Object 1 Position (X)

Detected object X-axis position

0,00 à 3,78 m

  • If the "ICS Received Data Invalid Flag" value is "Invalid", this item will not be valid.
  • Different values will be displayed for each detected object 1 to 3.

ICS Controlled Object 1 Position (Y)

Detected object Y-axis position

-3,84 à 3,72 m

  • If the "ICS Received Data Invalid Flag" value is "Invalid", this item will not be valid.
  • Different values will be displayed for each detected object 1 to 3.

ICS Recognition Sensor (Controlled Object 1)

Position of the sensor that detected the object

W/O / Send LH Center to LH Corner / Send LH Center to RH Center / Send RH Center to RH Corner / Send RH Center to LH Center / Send LH Corner to LH Center / Send RH Corner to RH Center

  • If the "ICS Received Data Invalid Flag" value is "Invalid", this item will not be valid.
  • Different values will be displayed for each detected object 1 to 3.

ICS Recognition Level (Controlled Object 1)

Length of time the object has been detected (level)

Without Level / Level 1 / Level 2 / Level 3

  • The higher the level, the longer the length of time the object has been detected.
  • If the "ICS Received Data Invalid Flag" value is "Invalid", this item will not be valid.
  • Different values will be displayed for each detected object 1 to 3.

ICS Controlled Object 2 Position (X)

Detected object X-axis position

0,00 à 3,78 m

  • If the "ICS Received Data Invalid Flag" value is "Invalid", this item will not be valid.
  • Different values will be displayed for each detected object 1 to 3.

ICS Controlled Object 2 Position (Y)

Detected object Y-axis position

-3,84 à 3,72 m

  • If the "ICS Received Data Invalid Flag" value is "Invalid", this item will not be valid.
  • Different values will be displayed for each detected object 1 to 3.

ICS Recognition Sensor (Controlled Object 2)

Position of the sensor that detected the object

W/O / Send LH Center to LH Corner / Send LH Center to RH Center / Send RH Center to RH Corner / Send RH Center to LH Center / Send LH Corner to LH Center / Send RH Corner to RH Center

  • If the "ICS Received Data Invalid Flag" value is "Invalid", this item will not be valid.
  • Different values will be displayed for each detected object 1 to 3.

ICS Recognition Level (Controlled Object 2)

Length of time the object has been detected (level)

Without Level / Level 1 / Level 2 / Level 3

  • The higher the level, the longer the length of time the object has been detected.
  • If the "ICS Received Data Invalid Flag" value is "Invalid", this item will not be valid.
  • Different values will be displayed for each detected object 1 to 3.

ICS Controlled Object 3 Position (X)

Detected object X-axis position

0,00 à 3,78 m

  • If the "ICS Received Data Invalid Flag" value is "Invalid", this item will not be valid.
  • Different values will be displayed for each detected object 1 to 3.

ICS Controlled Object 3 Position (Y)

Detected object Y-axis position

-3,84 à 3,72 m

  • If the "ICS Received Data Invalid Flag" value is "Invalid", this item will not be valid.
  • Different values will be displayed for each detected object 1 to 3.

ICS Recognition Sensor (Controlled Object 3)

Position of the sensor that detected the object

W/O / Send LH Center to LH Corner / Send LH Center to RH Center / Send RH Center to RH Corner / Send RH Center to LH Center / Send LH Corner to LH Center / Send RH Corner to RH Center

  • If the "ICS Received Data Invalid Flag" value is "Invalid", this item will not be valid.
  • Different values will be displayed for each detected object 1 to 3.

ICS Recognition Level (Controlled Object 3)

Length of time the object has been detected (level)

Without Level / Level 1 / Level 2 / Level 3

  • The higher the level, the longer the length of time the object has been detected.
  • If the "ICS Received Data Invalid Flag" value is "Invalid", this item will not be valid.
  • Different values will be displayed for each detected object 1 to 3.

Power Train Mode

Current Driving Mode

Normal / Power / Eco

-

SNOW Mode

SNOW mode indicator status

ON: SNOW mode indicator illuminated

OFF: SNOW mode indicator not illuminated

If the "Valid/Invalid of Driving Mode" value is "Invalid", this item will not be valid.

Valid/Invalid of Driving Mode

Validity information for SNOW mode

Valid / Invalid

-

VSC OFF Lamp

VSC OFF indicator status

ON: VSC OFF indicator illuminated

OFF: VSC OFF indicator not illuminated

If the "Valid/Invalid of TRC/VSC OFF Lamp" value is "Invalid", this item will not be valid.

TRC OFF Lamp

TRC OFF indicator status

ON: TRC OFF indicator illuminated

OFF: TRC OFF indicator not illuminated

If the "Valid/Invalid of TRC/VSC OFF Lamp" value is "Invalid", this item will not be valid.

Valid/Invalid of TRC/VSC OFF Lamp

Validity information for the TRC OFF and VSC OFF indicators

Valid / Invalid

-

EV Mode

EV mode indicator status

ON: EV mode indicator illuminated

OFF: EV mode indicator not illuminated

If the "Valid/Invalid of EV Mode" value is "Invalid", this item will not be valid.

Valid/Invalid of EV Mode

Validity information for EV mode

Valid / Invalid

-

Shift Gear

Gear selected (or range) shown on the instrument cluster when the shift lever is in M (or S) position

OFF: Not shown on the instrument cluster

1st to 8th: Selected gear/range shown on the instrument cluster

The displayed gear may differ from the gear actually engaged.

Engine Load Factor

Engine load

0,0 à 100,0 %

"Invalid" is displayed for hybrid and diesel vehicles.

READY Signal

Vehicle can be driven

ON: "Vehicle can be driven" message displayed

OFF: "Vehicle cannot be driven" message not displayed

"Invalid" is displayed for gasoline and diesel vehicles.

Gear Position Signal

Gear Engaged

1st/2nd/3rd/4th/5th/6th/7th/8th

  • "Invalid" is displayed for vehicles equipped with the hybrid system.
  • "1" is always displayed for vehicles equipped with a continuously variable transmission.

Turbine RPM/Input Shaft RPM

Torque Converter Output Shaft Speed (Transmission Input Shaft Speed)

0 to 12,650 rpm

-

Under VSC Control

VSC Operation

ON: Operating

OFF: Not operating or not present

-

Under ABS Control

ABS Operation

ON: Operating

OFF: Not operating or not present

-

Under VDM Control

VDIM Operation

ON: Operating

OFF: Not operating or not present

-

Under TRC Operation Flag

TRC Operation

ON: Operating

OFF: Not operating or not present

-

FR Wheel Speed

Front right wheel speed

-327,68 à 328 km/h

If the value is equal to or greater than 328 km/h, "327.65 km" is displayed.

FL Wheel Speed

Front left wheel speed

-327,68 à 328 km/h

If the value is equal to or greater than 328 km/h, "327.65 km" is displayed.

RR Wheel Speed

Right rear wheel rotation speed

-327,68 à 328 km/h

If the value is equal to or greater than 328 km/h, "327.65 km" is displayed.

RL Wheel Speed

Left rear wheel rotation speed

-327,68 à 328 km/h

If the value is equal to or greater than 328 km/h, "327.65 km" is displayed.

Cruise System

Cruise control system malfunction

Normal / Fault / Invalid

-

Driving Force Demand Judgment Flag

Driving Force Demand

Driving Force / Non-Driving Force

A fixed value is displayed for each vehicle.

Cruise Control Master Switch Flag

Master command that determines the vehicle speed when cruise control is active (Power Train / DSS (Driving Support System))

Power Train / DSS

  • If the value of "Cruise System" is "Fault" or "Invalid", this item will not be valid.
  • A fixed value is displayed for each vehicle.

DSS Judgment Flag

Presence of a DSS (Driving Support System)

Yes/No

If the value of "Cruise System" is "Fault" or "Invalid", this item will not be valid.

Cruise Control Res/Accel SW

Cruise control RES/+ (ACCEL) switch status

ON / OFF

If the value of "Cruise System" is "Fault" or "Invalid", this item will not be valid.

Cruise Control Set/Coast SW

Cruise control SET/- (COAST) switch status

ON / OFF

If the value of "Cruise System" is "Fault" or "Invalid", this item will not be valid.

Cruise Control Cancel SW

Cruise control CANCEL switch status

ON / OFF

If the value of "Cruise System" is "Fault" or "Invalid", this item will not be valid.

Cruise Control Brake SW

Brake light switch status while cruise control is operating

ON / OFF

If the value of "Cruise System" is "Fault" or "Invalid", this item will not be valid.

Cruise Control D Signal

Shift lever in D position while cruise control is operating

ON / OFF

If the value of "Cruise System" is "Fault" or "Invalid", this item will not be valid.

Cruise Control Main SW

Cruise control main switch status

ON / OFF

If the value of "Cruise System" is "Fault" or "Invalid", this item will not be valid.

Cruise Control Set Speed

Set the vehicle speed for cruise control

0 à 255 km/h

If the value of "Cruise System" is "Fault" or "Invalid", this item will not be valid.

Vehicle Speed (during Cruise Control)

Vehicle speed while cruise control is operating

0 à 255 km/h

If the value of "Cruise System" is "Fault" or "Invalid", this item will not be valid.

Cruise Control Request Value

Throttle valve opening angle (when the value of "Driving Force Demand Judgment Flag" is "Non-Driving Force") or driving force (when the value of "Driving Force Demand Judgment Flag" is "Driving Force") requested by the cruise control system

Throttle valve opening angle: 0.0 to 127.5 %

Driving force: -12,800 to 12,700 N

  • The values displayed for this item and "Driving Force Demand Judgment Flag" will differ.
  • If the value of "Cruise System" is "Fault" or "Invalid", this item will not be valid.

ACC Target Distance

Distance to the preceding vehicle in ACC (Adaptive Cruise Control) vehicle-to-vehicle distance control mode

0 à 251 m

If the value of "Cruise System" is "Fault" or "Invalid", this item will not be valid.

ACC Target Condition

Control status of the ACC (Adaptive Cruise Control) system

Forward Vehicle / No Forward Vehicle / Constant Speed Mode / Radar Failure

If the value of "Cruise System" is "Fault" or "Invalid", this item will not be valid.

ACC Relative Speed

Relative speed of the preceding vehicle in ACC (Adaptive Cruise Control) vehicle-to-vehicle distance control mode

-128 à 127 km/h

  • A negative value is displayed when approaching the preceding vehicle.
  • If the value of "Cruise System" is "Fault" or "Invalid", this item will not be valid.

PCS Reception Data Invalid Flag

Validity of PCS data

Valid / Invalid

-

ALM Request Flag 2

PCS indicator operation command 2 from the driving support ECU to the skid control buzzer and instrument cluster assembly

ON / OFF

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

ALM Request Flag

PCS indicator operation command 1 from the driving support ECU to the skid control buzzer and instrument cluster assembly

ON / OFF

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

ABK Request Flag

Brake assist warning request command from the driving support ECU to the skid control ECU

ON / OFF

  • Displayed only for vehicles equipped with a driver monitor camera.
  • If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

PBA Request Flag

PCS brake assist request command from the driving support ECU to the skid control ECU

OFF / PBA1 ON / PBA2 ON / PBA3 ON

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

FPB Request Flag

PCS brake (preliminary braking) command from the driving support ECU to the skid control ECU

ON / OFF

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

PB Request Flag

PCS brake (actuation) command from the driving support ECU to the skid control ECU

ON / OFF

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

PSB Request Flag

PCS preventive seat belt operation command from the driving support ECU to the preventive seat belt control ECU

ON / OFF

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

Prefill Request Flag

PCS Brake (Standby) Request from Driving Support ECU to Skid Control ECU

ON / OFF

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

Stop Lamp Lighting Request Flag

Stop Lamp Lighting Request from Driving Support ECU to Skid Control ECU

ON / OFF

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

PCS Brake Hold Request Flag

PCS Brake Hold Request after PCS Operation from Driving Support ECU to Skid Control ECU

ON / OFF

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

Collision Avoidance Assist Request Flag 1

Collision Avoidance Assist Request 1 from Driving Support ECU to VGRS/DSR

ON / OFF

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

Collision Avoidance Assist Request Flag 2

Collision Avoidance Assist Request 2 from Driving Support ECU to VGRS/DSR

ON / OFF

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

Collision Avoidance Assist Request Flag 3

Collision Avoidance Assist Request 3 from Driving Support ECU to VGRS/DSR

ON / OFF

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

PCS SW

PCS ON/OFF Position Depending on Switch Operation

ON / OFF

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

PCS Display (Diag Condition)

PCS Warning Message Status

ON / OFF

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

PCS Display (Millimeter Wave Dirt)

Dirt, etc. Detected on Millimeter Wave Radar Sensor

ON / OFF

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

PCS Display (Temporarily not available)

PCS Temporarily Unavailable

System Available / System Not Available

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

PCS Display (Sensor Recognition Status)

Recognition Sensor Status

Status1 / Status2

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

PCS Display (Millimeter Wave Radar Low Voltage Status)

Millimeter Wave Radar Sensor Low Voltage

Normal / Low

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

PCS Display (Camera Backlight Status)

Camera Backlight Present

Normal / Backlight

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

PCS Display (Millimeter Wave Radar Alignment Flag)

Millimeter Wave Radar Sensor Beam Axis Alignment Status

ON / OFF

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

PCS Display (Object Recognition Status)

Target Recognition Status

Status1 / Status2

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

PCS Display (Control Status 1)

PCS Control Status 1

Level1 / Level2 / Level3 / Level4

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

PCS Display (Control Status 2)

PCS Control Status 2

Level1 / Level2 / Level3 / Level4

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

Target Distance

Distance to PCS Control Target Object

0,00 à 100,33 m

  • If an object is detected but PCS control is judged unnecessary, the maximum value is displayed.
  • If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

Target Relative Velocity

Relative Velocity of PCS Control Target Object

-57,540 à 14,000 m/s

  • A negative value is displayed when approaching the target object.
  • If an object is detected but PCS control is judged unnecessary, the maximum value is displayed.
  • If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

Target Lateral Position

Lateral Position of PCS Control Target Object

-5,12 à 4,80 m

  • A positive value is displayed when the detected object is to the right of the vehicle centerline.
  • A negative value is displayed when the detected object is to the left of the vehicle centerline.
  • If an object is detected but PCS control is judged unnecessary, the maximum value is displayed.
  • If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

Target Object Number

Number of objects detected by the sensors that are considered as PCS control target objects.

1 à 33

  • If "1" is displayed when the maximum value for each recorded data item ("Target Distance", "Target Relative Velocity", "Target Lateral Position") is displayed, PCS control operation is judged unnecessary.
  • If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

Relative Acceleration for Control Target

Relative Acceleration of PCS Control Target Object

-8 à 7 m/s2

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

Predicted Time to Collision 1 for Control Target

Estimated Time to Collision with PCS Control Target Object 1

0,0 à 6,3 s

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

Predicted Time to Collision 2 for Control Target

Estimated Time to Collision with PCS Control Target Object 2

0,0 à 6,3 s

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

Predicted Time to Collision Status for Control Target

Estimated Time to Collision Status of PCS Control Target Object

Status1 / Status2

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

Sensor Recognition Status for Control Target

Recognition Sensor Status

Status1 to Status10

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

Type of the Object for Control Target

Object Type for PCS Control Target

Type1 to Type12

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

PCS ALM Mode Status

PCS Warning Light Sensitivity Setting

OFF / Far / Middle / Near

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

PCS ALM Status

PCS Warning Light Status

Status1 to Status3

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

PCS Guard Status C

PCS Guard Status C

Status1 / Status2

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

PCS Guard Status B

PCS Guard Status B

Status1 / Status2

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

PCS Guard Status A

PCS Guard Status A

Status1 to Status4

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

Sensor Recognition Status (Horizontal Axis Offset Status of Millimeter Wave Radar)

Horizontal Axis Offset of Millimeter Wave Radar Sensor

Status1 / Status2

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

Sensor Recognition Status (Vertical Axis Offset Status of Millimeter Wave Radar)

Vertical Misalignment of Millimeter-Wave Radar Sensor

Status1 to Status8

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

Estimated Curve Radius

Estimated Driving Path Curve Radius

-6 400 à 6 200 m

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

Detection of Certain Level of Acceleration

Acceleration Above Threshold Detected

Not Supported / No / Invalid / Yes

If the value of "PCS Reception Data Invalid Flag" is "Invalid", this item will not be valid.

LKA DDR Trigger Signal

LKA/LDA Trigger Detection (Trigger ID No. 19)

Trigger OFF: Conditions not met

Trigger Condition 1: Condition 1 met

Trigger Condition 2: Condition 2 met

Trigger Condition 3: Condition 3 met

If the "Invalid of LKA DDR Data" value is "Invalid", this item is not valid.

Invalid of LKA DDR Data

Validity of LKA/LDA Information

Valid / Invalid

-

Steering Wheel Release Condition

Driver's Hands on Steering Wheel during LKA Evaluation

ON: Hands not detected on steering wheel

OFF: Hands detected on steering wheel

If the "Invalid of LKA DDR Data" value is "Invalid", this item is not valid.

Steering Operation of LKA

Steering Wheel Operation during LKA Evaluation

ON: Steering wheel is operated

OFF: Steering wheel is not operated

If the "Invalid of LKA DDR Data" value is "Invalid", this item is not valid.

Steering Operation of LDA

Steering Wheel Operation during LDA Evaluation

ON: Steering wheel is operated

OFF: Steering wheel is not operated

If the "Invalid of LKA DDR Data" value is "Invalid", this item is not valid.

LKA Control Condition (EPS Control)

EPS Control Status

ON: EPS is operating

OFF: EPS is not operating

If the "Invalid of LKA DDR Data" value is "Invalid", this item is not valid.

LKA Control Condition

LKA/LDA Control Status

LKA available: LKA operation possible

LDA available: LDA operation possible

OFF: LKA/LDA operation not possible

If the "Invalid of LKA DDR Data" value is "Invalid", this item is not valid.

Turn Signal Operation

Turn Signal Operation Status

OFF / Right Turn ON / Left Turn ON

If the "Invalid of LKA DDR Data" value is "Invalid", this item is not valid.

EPS Torque Sensor Value

EPS Assist Amount

-12,5 à 12,5 N·m

A positive value is displayed when the steering wheel is turned to the left.

HV Recognition Flag

Hybrid Vehicle Estimation

HV: Hybrid vehicle

Other than HV: Gasoline or diesel vehicle

-

Diesel Flag

Diesel Vehicle Evaluation

Diesel: Diesel vehicle

Not diesel: Gasoline or hybrid vehicle

-

Sensor Type Identification (Yaw Rate Sensor)

Number of Yaw Rate Sensors Installed

1 / 2

A fixed value is displayed for each vehicle.

Sensor Type Identification (G Sensor)

Number of G Sensors Installed

1 / 2

A fixed value is displayed for each vehicle.

Sensor Type Identification (G Sensor Layout)

G Sensor Installation Angle relative to Vehicle Longitudinal Axis

45 deg. / 90 deg.

A fixed value is displayed for each vehicle.

Sensor Type Identification (Security)

Presence of Tilt Sensor

With/Without

A fixed value is displayed for each vehicle.

Yaw G Sensor Installation Information

G Sensor Installation Orientation (normal or reversed (180° from normal))

Original / Count

A fixed value is displayed for each vehicle.

DSC Operation Flag

DSC Operation (Start Control)

ON: Operating

OFF: Not operating or invalid

-