Toyota Camry Quiz
Introduction

Oil pump seal (1MZ−FE/3MZ−FE)

In this manual: Introduction
Introduction — 61Audio & visual system — 16Automatic transmission / trans — 19Transmission revolution (ATM) — 1Shift lock system (ATM) — 1Brake — 20Clutch — 10Communication system — 4Cooling — 15Cruise control — 3Drive shaft / propeller shaft — 9Emission control — 8Engine control system — 12Engine hood/door — 7Exhaust — 3Exterior/interior trim — 14Front suspension — 9Fuel — 12Heater & air conditioner — 16Ignition — 8Instrument panel/meter — 7Intake — 7Lighting — 11Lubrication — 16Manual transmission/transaxle — 13Parking brake — 10Power steering — 7Rear suspension — 10Seat — 12Service specifications — 26Sliding roof/convertible — 4Starting & charging — 11Starting system (2AZ−FE)(From July, 2003) — 1Starting system (1MZ−FE/3MZ−FE) — 1Steering column — 6Theft deterrent & door lock — 9Tire & wheel — 4Windshield/windowglass/mirror — 5Back window glass — 1Power window control system — 1Power mirror control system — 1Inner rear view mirror assy — 1Windshield glass — 1Wiring — 1
34steps
~204min
4/5difficulty
0102030405086N·mlb·ft
Tightening torque found on this page
Done 0 of 34
REPLACEMENT
  1. REMOVE FRONT WHEEL RH
  2. REMOVE FRONT FENDER APRON SEAL RH
  3. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT No.1
  4. REMOVE VANE PUMP V BELT
  5. REMOVE ENGINE MOVING CONTROL ROD
  6. REMOVE ENGINE MOUNTING STAY No.2 RH
  7. REMOVE GENERATOR BRACKET No.2
  8. REMOVE CRANKSHAFT PULLEY
  9. REMOVE TIMING BELT No.1 COVER
  10. REMOVE TIMING BELT No.2 COVER
  11. REMOVE ENGINE MOUNTING BRACKET RH
  12. REMOVE TIMING BELT GUIDE No.2
  13. REMOVE TIMING BELT
  14. REMOVE CRANKSHAFT TIMING PULLEY

  15. Remove the bolt and the timing belt plate.

  16. Install the pulley bolt to the crankshaft.

  17. Using SST, remove the crankshaft timing pulley.

    SST 09950−50013 (09951−05010, 09952−05010, 09953−05020, 09954−05010)

NOTICE:
  • Do not scratch the part of the crankshaft timing pulley.
  • Before using SST, apply lubricating oil on the threads and tip of the center bolt 150.
Remove crankshaft timing pulley
Remove crankshaft timing pulley 15. REMOVE OIL PUMP SEAL

  1. Using a knife, cut through the oil seal lip.

  2. Using a screwdriver with its tip wrapped in tape, pry out the oil seal.

NOTICE: After the removal, check the crankshaft for damage. If it is damaged, smooth the surface with 400−grit sandpaper. 6. INSTALL OIL PUMP SEAL

a. Apply MP grease to a new oil seal lip.

NOTICE: Keep the lip free of foreign matter.
b. Using SST and a hammer, tap in the oil seal until its

b. Using SST and a hammer, tap in the oil seal until its surface is flush with the oil pump edge.

SST 09223−00010

NOTICE:
  • Be careful not to tap the oil seal slantingly.
  • Wipe off extra grease on the crankshaft.
17. INSTALL CRANKSHAFT TIMING PULLEY
17. INSTALL CRANKSHAFT TIMING PULLEY

a. Align the keyway of the pulley with the key located on the crankshaft and slide the pulley into place.

NOTICE: Do not scratch the part of the crankshaft timing pulley.

b. Install the timing belt plate with the bolt.

Torque: 8 N·m Install crankshaft timing pulley
Install crankshaft timing pulley
  1. INSPECT TIMING BELT
  2. INSTALL TIMING BELT
  3. INSTALL TIMING BELT GUIDE No.2
  4. INSTALL ENGINE MOUNTING BRACKET RH Torque: 28 N·m
  5. INSTALL TIMING BELT No.2 COVER
  6. INSTALL TIMING BELT No.1 COVER
  7. INSTALL CRANKSHAFT PULLEY
  8. INSTALL GENERATOR BRACKET No.2 Torque: 28 N·m
  9. INSTALL ENGINE MOUNTING STAY No.2 RH
  10. INSTALL ENGINE MOVING CONTROL ROD
  11. INSTALL VANE PUMP V BELT
  12. INSTALL V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT No.1
  13. INSPECT DRIVE BELT TENSION
  14. INSTALL FRONT WHEEL RH
  15. CHECK FOR ENGINE OIL LEAKS

Test yourself

A quick Toyota Camry quiz: every answer comes with an explanation and a link to the manual page.