Toyota Sienna Quiz
Audio / visual

Speaker Circuit

In this manual: Audio / visual
Introduction — 55Service specifications — 7Maintenance — 7Engine — 264U151e automatic transaxle — 108Transfer — 19Propeller shaft — 8Drive shaft — 14Differential — 16Axle — 18Suspension — 37Tire and wheel — 54Brake control — 141Parking brake — 16Steering Column — 11Power steering — 18Air conditioning — 106Supplemental restraint system — 146Seat belt — 22Theft deterrent — 14Engine immobiliser — 17Cruise control — 65Lighting — 61Wiper and washer — 13Door lock — 42Meter — 28Audio / visual — 94Navigation — 108Park assist / monitoring — 33Horn — 5Garage door opener — 42GR-FE Engine control system — 126Supplemental restraint system — 147Other system — 14Windshield / windowglass — 43Mirror — 23Instrument panel — 6Seat belt — 22Seat — 92Engine hood / door — 104Exterior — 39Interior — 5Sliding roof — 9Multiplex communication — 18Can communication — 23
10steps
~60min
3/5difficulty
Done 0 of 10

DESCRIPTION

  • When the vehicle has a built-in type amplifier, a sound signal is sent from the radio receiver to the speakers via the "6 Speaker System" circuit.
  • When the vehicle has a separate type amplifier, a sound signal from the radio receiver is amplified by the stereo component amplifier and then transmitted to the speaker via the "10 Speaker System" circuit.

If there is a short in this circuit, the stereo component amplifier detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier or speakers

WIRING DIAGRAM

WIRING DIAGRAM
WIRING DIAGRAM
WIRING DIAGRAM

1 CHECK HARNESS AND CONNECTOR

CHECK HARNESS AND CONNECTOR
  1. Disconnect the connectors shown in the illustration from the stereo component amplifier or radio receiver and speakers.
  2. 10 Speaker System: Measure the resistance between each of the front No. 2 speakers and the stereo component amplifier to check for an open circuit in the wire harness.

Standard resistance: Below 1 Ω

  • 6 speaker System: Measure the resistance between each of the front No. 2 speakers and the radio receiver to check for an open circuit in the wire harness.

    • Standard resistance: Below 1 Ω

  • Measure the resistance between each of the front No. 2 speakers and each of the front No. 1 speakers to check for an open circuit in the wire harness.

    • Standard resistance: Below 1 Ω

  • 10 Speaker System: Measure the resistance between each of the rear speakers and the stereo component amplifier to check for an open circuit in the wire harness.

    • Standard resistance: Below 1 Ω

  • 6 Speaker System: Measure the resistance between each of the rear speakers and the radio receiver to check for an open circuit in the wire harness.

    • Standard resistance: Below 1 Ω

  • 10 Speaker System: Measure the resistance between each of the rear stereo component speakers and the stereo component amplifier to check for an open circuit in the wire harness.

    • Standard resistance: Below 1 Ω

  • 10 Speaker System: Measure the resistance between the front stereo component speaker and the stereo component amplifier to check for an open circuit in the wire harness.

    • Standard resistance: Below 1 Ω
    CHECK HARNESS AND CONNECTOR
    1. 10 Speaker System: Measure the resistance between the woofer box speaker and the stereo component amplifier to check for an open circuit in the wire harness.

    Standard resistance: Below 1 Ω

  • Measure the resistance between the each speaker and body ground to check for a short circuit in the wire harness.

    • Standard resistance: 10 kΩ or higher

    2 INSPECT FRONT NO. 1 SPEAKER

    1. Resistance check.
    2. Measure the resistance between the terminals of the speaker.
    Standard resistance: 10 Speaker System: 4 to 6 Ω
    6 Speaker System: Approximately 4 Ω

    3 INSPECT REAR SPEAKER

    1. Resistance check.
    2. Measure the resistance between the terminals of the speaker.
    10 Speaker System: Approximately 2.4 Ω
    6 Speaker System: Approximately 4 Ω

    4 INSPECT FRONT NO. 2 SPEAKER

    1. Check that the malfunction disappears when another speaker in good condition is installed.
    Standard: Malfunction disappears.

    HINT:

    • Connect all the connectors to the front No. 2 speaker.
    • When there is a possibility that either the right or left front speaker is detective, inspect by interchanging the right one with the left one.
    • Perform the above inspection on both LH and RH sides.

    5 CONFIRM MODEL

    Result

    Result

    6 INSPECT WOOFER BOX SPEAKER

    INSPECT WOOFER BOX SPEAKER
    1. Resistance check.
    2. Measure the resistance according to the value(s) in the table below.

    NOTICE: The speaker should not be removed for checking.

    Standard resistance

    Standard resistance

    7 INSPECT REAR STEREO COMPONENT SPEAKER

    1. Check that the malfunction disappears when another speaker in good condition is installed.

    OK: Malfunction disappears.

    HINT:

    • Connect all the connectors to the rear stereo component speaker.
    • When there is a possibility that either the right or left rear speaker is detective, inspect by interchanging the right one with the left one

    8 INSPECT FRONT STEREO COMPONENT SPEAKER

    1. Resistance check.
    2. Measure the resistance between the terminals of the speaker.
    Standard resistance: 1.2 to 2.2 Ω

    PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

    Test yourself

    A quick Toyota Sienna quiz: every answer comes with an explanation and a link to the manual page.