The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th, 5th or 6th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body and automatic transmission (clutch, brake, gear, etc.).
DTC Code
DTC Detection Condition
Trouble Area
P0761
S3 stuck ON malfunction*1:
When the ECM directs the transmission to switch to 5th or 6th gear, the engine overruns (clutch slips).
The ECM determines there is a malfunction when either of the following conditions is met (2-trip detection logic):
(a) When the ECM directs the transmission to switch to 4th gear, the actual gear is shifted to 3rd.
(b) When the ECM directs the transmission to switch to 5th gear, the engine overruns (clutch slips).
Gear positions in the event of a solenoid valve mechanical problem:
ECM gear shift command
1st
2nd
3rd
4th
5th
6th
*1: Actual gear position under S3 stuck ON malfunction
1st
2nd
3rd
3rd
N*
N*
*2: Actual gear position under S3 stuck OFF malfunction
3rd
4th
4th
4th
5th
6th
N*: Neutral
Gear position during fail-safe operation:
If any malfunction is detected, the ECM changes into the fail-safe mode to shift into the gear positions as shown in the table below.
Gear position under normal conditions
1st
2nd
3rd
4th
5th
6th
*1: Actual gear position under fail-safe mode during S3 stuck ON malfunction
1st
2nd
3rd
3rd
3rd
3rd
*2: Actual gear position under fail-safe mode during S3 stuck OFF malfunction
3rd
4th
4th
4th
5th
6th
MONITOR DESCRIPTION
This DTC indicates a "stuck ON malfunction" or "stuck OFF malfunction" of the shift solenoid valve S3.
The ECM commands gear shifts by turning the shift solenoid valves ON/OFF. When the gear position commanded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores the DTC.
MONITOR STRATEGY
Related DTCs
P0761: Shift solenoid valve S3/Functional check
Required sensors/Components
Shift solenoid valve S3
Frequency of operation
Continuous
Duration
OFF malfunction (A), (B) and ON malfunction (A)
0.4 seconds
ON malfunction (B)
3 seconds
ON malfunction (C)
1 second
MIL operation
2 driving cycles
Sequence of operation
None
TYPICAL ENABLING CONDITIONS
All
The monitor will run whenever the following DTCs are not present
P0717 (Turbine speed sensor circuit)
P0722 (Output Speed Sensor circuit)
P0710, P0712, P0713, P2740, P2742, P2743 (ATF temperature sensor circuit)
Both of the following conditions are met: OFF malfunctions (A) and (B)
OFF Malfunction (A)
Turbine speed / Output speed (NT / NO)
0.93 or more, and 1.07 or less
(This means actual gear is 4th)
OFF Malfunction (B)
Turbine speed / Output speed (NT / NO)
0.51 or more, and 0.65 or less
(This means actual gear is 6th)
[ON malfunction]
One of the following conditions is met: ON malfunctions (A), (B) or (C)
ON Malfunction (A)
Turbine speed / Output speed (NT / NO)
1.28 or more, and 1.53 or less
(This means actual gear is 3rd)
ON Malfunction (B)
Turbine speed - Output speed x 4th gear ratio
(NT - NO x 4th gear ratio)
1000 rpm or more
ON Malfunction (C)
Turbine speed - Output speed x 5th gear ratio
(NT - NO x 5th gear ratio)
1000 rpm or more
NOTICE:
Perform the universal trip to clear permanent DTCs (See page ).
1. ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the Techstream to the DLC3.
(d) Turn the ignition switch to ON.
(e) Turn the Techstream on.
(f) Enter the following menus: Powertrain / Engine and ECT / Active Test.
(g) According to the display on the Techstream, perform the Active Test.
HINT:
While driving, the shift position can be forcibly changed with the Techstream.
Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (See page ).
Engine and ECT
Tester Display
Test Part
Control Range
Diagnostic Note
Control the Shift Position
Operate shift solenoid valves and set each shift position
Press "→" button: Shift up
Press "←" button: Shift down
Possible to check operation of the shift solenoid valves.
[Vehicle Condition]
50 km/h or less
HINT:
This test can be conducted when the vehicle speed is 50 km/h or less.
The 4th to 5th and 5th to 6th up-shifts must be performed with the accelerator pedal released.
The 6th to 5th and 5th to 4th down-shifts must be performed with the accelerator pedal released.
Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
The shift position commanded by the ECM is shown in the Data List display on the Techstream.
The shift solenoid valve SL2 turns ON/OFF normally when the shift lever is in D.
ECM gear shift command
1st
2nd
3rd
4th
5th
6th
Shift solenoid valve S3
ON
ON
ON
OFF
OFF
OFF
PROCEDURE
CHECK DTC OUTPUT (IN ADDITION TO DTC P0761)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(e) Read the DTCs using the Techstream.
Result
Result
Proceed to
Only P0761 is output
A
P0761 and other DTCs are output
B
HINT:
If any other codes besides P0761 are output, perform troubleshooting for those DTCs first.
B
GO TO DTC CHART
A
PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT)
NG
REPLACE SHIFT SOLENOID VALVE SLT
OK
INSPECT SHIFT SOLENOID VALVE S3
(a) Remove shift solenoid valve S3.
(b) Measure the resistance according to the value(s) in the table below.