Shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and vehicle speed sensor. The ECM adjusts the current to shift solenoid valve SLT to control the hydraulic line pressure coming from the primary regulator valve.
Appropriate line pressure assures smooth shifting with varying engine outputs.
DTC Code
DTC Detection Condition
Trouble Area
P0894
The ECM detects a malfunction in shift solenoid valve SLT, S1, S2, S3, S4 or SL2, or the 1-2 shift valve, or an incorrect gear 6 ratio according to the difference in speed of the turbine and output shaft, and also by the oil pressure (2-trip detection logic).
Shift solenoid valve SLT remains open or closed
Shift solenoid valve S1, S2, S3, S4 or SL2 remains open or closed
Gear 6 incorrect ratio (sequence valve) or 1-2 shift valve is stuck
The ECM detects a malfunction in shift solenoid valve SLT (ON side) according to the difference in speed of the turbine and output shaft, and also by the oil pressure (2-trip detection logic).
Shift solenoid valve SLT remains open or closed
Shift solenoid valve S1, S2, S3, S4 or SL2 remains open or closed
Gear 6 incorrect ratio (sequence valve) or 1-2 shift valve is stuck
The ECM calculates the amount of heat absorbed by the friction material based on the difference in speed (clutch slippage) between the turbine and output shaft. The ECM illuminates the MIL and stores this DTC when the amount of heat absorption exceeds the specified value.
There are two causes of speed difference.
When the shift solenoid valve SLT remains ON, oil pressure decreases, which causes the clutch engagement force to decrease.
When a shift solenoid valve remains ON or OFF, the gear position commanded by the ECM and the actual gear position are not the same.
NOTICE:
If you continue driving under these conditions, the clutch will burn out and the vehicle will no longer be drivable.
MONITOR STRATEGY
Related DTCs
P0894: Automatic transmission slip malfunction
P2714: Shift solenoid valve SLT/Functional check
Required sensors/Components
Shift solenoid valve SLT
Frequency of operation
Continuous
Duration
P0894 ON malfunction (A): Immediately
P0894 ON malfunction (B): 0.4 seconds
P2714: Immediately
MIL operation
2 driving cycles
Sequence of operation
None
TYPICAL ENABLING CONDITIONS
All
The monitor will run whenever the following DTCs are not present
P0717 (Turbine speed sensor circuit)
P0722 (Output Speed Sensor circuit)
P0710, P0712, P0713, P2740, P2742, P2743 (ATF temperature sensor circuit)
Spark advance from max. retard timing by KCS control
0° crankshaft angle or more
Engine
Starting
TYPICAL MALFUNCTION THRESHOLDS
[P0894: ON malfunction]
When either condition below is met: ON malfunction (A) or (B)
ON Malfunction (A)
Summation of C1 clutch heat generations
Specified value
ON Malfunction (B)
Summation of C2 clutch heat generations
Specified value
Actual gear for SLT failure judgment
Not determined
[P2714: ON malfunction]
One of the following conditions is met: ON malfunction (A), (B), (C), (D), (E), (F), (G) or (H)
ON Malfunction (A)
Summation of C1 clutch heat generations
Specified value
ON Malfunction (B)
Shift solenoid valve S1 OFF malfunction
Detected
ON Malfunction (C)
Shift solenoid valve S2 OFF malfunction
Detected
ON Malfunction (D)
Shift solenoid valve S3 ON malfunction
Detected
ON Malfunction (E)
Shift solenoid valve S4 OFF malfunction
Detected
ON Malfunction (F)
1-2 shift valve malfunction
Detected
ON Malfunction (G)
Reverse sequence valve malfunction
Detected
ON Malfunction (H)
Shift solenoid valve SL2 ON malfunction
Detected
NOTICE:
Perform the universal trip to clear permanent DTCs (See page ).
PROCEDURE
CHECK DTC OUTPUT (IN ADDITION TO DTCS P0894 AND P2714)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(e) Read the DTCs using the Techstream.
Result
Result
Proceed to
Only P0894 is output
Only P0894 and P2714 are output
A
P0894, P2714 and other DTCs are output
B
HINT:
If any other codes besides P0894 and P2714 are output, perform troubleshooting for those DTCs first.
B
GO TO DTC CHART
A
PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT)
NG
GO TO STEP 17
OK
PERFORM ACTIVE TEST USING TECHSTREAM (RUNNING TEST)
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Clear the DTC (See page ).
(c) Enter the following menus: Powertrain / Engine and ECT / Active Test.
(d) According to the display on the Techstream, perform the Active Test.
HINT:
While driving, the shift position can be forcibly changed with the Techstream.
Engine and ECT
Tester Display
Test Part
Control Range
Diagnostic Note
Control the Shift Position
Operate shift solenoid valves and set each shift position
Press "→" button: Shift up
Press "←" button: Shift down
Possible to check operation of the shift solenoid valves.
[Vehicle Condition]
50 km/h or less
HINT:
This test can be conducted when the vehicle speed is 50 km/h or less.
The 4th to 5th and 5th to 6th up-shifts must be performed with the accelerator pedal released.
The 6th to 5th and 5th to 4th down-shifts must be performed with the accelerator pedal released.
Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
The shift position commanded by the ECM is shown in the Data List display on the Techstream.
(e) Compare the ECM gear shift command and the actual gear position.
Result
ECM Gear Shift Command
1st
2nd
3rd
4th
5th
6th
Proceed to
Actual gear position under malfunction
Shift solenoid S1
Stuck ON*1
2nd
2nd
3rd
4th
5th
6th
A
Stuck OFF
1st
1st
3rd
4th
5th
N*2
Shift solenoid S2
Stuck ON
1st
2nd
2nd
4th
6th
6th
B
Stuck OFF
3rd
3rd
3rd
4th
5th
5th
Shift solenoid S3
Stuck ON
1st
2nd
3rd
3rd
N*2
N*2
C
Stuck OFF
3rd
4th
4th
4th
5th
6th
Shift solenoid S4
Stuck ON*3
1st
2nd
3rd
4th
5th
6th
D
Stuck OFF
1st
2nd
3rd
4th
4th
4th
Actual gear position when normal
1st
2nd
3rd
4th
5th
6th
E
HINT:
*1: When shift solenoid S1 is stuck ON, the vehicle cannot drive in reverse.
*2: Neutral
*3: When shift solenoid S4 is stuck ON, gear shifting is normal.
B
GO TO STEP 7
C
GO TO STEP 10
D
GO TO STEP 13
E
GO TO STEP 20
A
INSPECT SHIFT SOLENOID VALVE S1
NG
REPLACE SHIFT SOLENOID VALVE S1
OK
INSPECT TRANSMISSION VALVE BODY ASSEMBLY
NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY
OK
INSPECT TORQUE CONVERTER ASSEMBLY
(a) Check the torque converter assembly (See page ).
OK:
The torque converter operates normally.
OK
REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY
NG
REPLACE TORQUE CONVERTER ASSEMBLY
INSPECT SHIFT SOLENOID VALVE S2
NG
REPLACE SHIFT SOLENOID VALVE S2
OK
INSPECT TRANSMISSION VALVE BODY ASSEMBLY
NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY
OK
INSPECT TORQUE CONVERTER ASSEMBLY
(a) Check the torque converter assembly (See page ).
OK:
The torque converter operates normally.
OK
REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY
NG
REPLACE TORQUE CONVERTER ASSEMBLY
INSPECT SHIFT SOLENOID VALVE S3
NG
REPLACE SHIFT SOLENOID VALVE S3
OK
INSPECT TRANSMISSION VALVE BODY ASSEMBLY
NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY
OK
INSPECT TORQUE CONVERTER ASSEMBLY
(a) Check the torque converter assembly (See page ).
OK:
The torque converter operates normally.
OK
REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY
NG
REPLACE TORQUE CONVERTER ASSEMBLY
INSPECT SHIFT SOLENOID VALVE S4
NG
REPLACE SHIFT SOLENOID VALVE S4
OK
INSPECT SHIFT SOLENOID VALVE SL2
NG
REPLACE SHIFT SOLENOID VALVE SL2
OK
INSPECT TRANSMISSION VALVE BODY ASSEMBLY
NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY
OK
INSPECT TORQUE CONVERTER ASSEMBLY
(a) Check the torque converter assembly (See page ).
OK:
The torque converter operates normally.
OK
REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY
NG
REPLACE TORQUE CONVERTER ASSEMBLY
INSPECT SHIFT SOLENOID VALVE SLT
(a) Remove shift solenoid valve SLT.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20 °C
5.0 to 5.6 Ω
(c) Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
OK:
Measurement Condition
Specified Condition
Battery positive (+) with a 21 W bulb → Terminal 2
Battery negative (-) → Terminal 1
Valve moves and makes an operating noise
Text in Illustration
*a
Component without harness connected
(Shift Solenoid Valve SLT)
NG
REPLACE SHIFT SOLENOID VALVE SLT
OK
INSPECT TRANSMISSION VALVE BODY ASSEMBLY
NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY
OK
INSPECT TORQUE CONVERTER ASSEMBLY
(a) Check the torque converter assembly (See page ).
OK:
The torque converter operates normally.
OK
REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY
NG
REPLACE TORQUE CONVERTER ASSEMBLY
INSPECT SHIFT SOLENOID VALVE SLT
(a) Remove shift solenoid valve SLT.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20 °C
5.0 to 5.6 Ω
(c) Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
OK:
Measurement Condition
Specified Condition
Battery positive (+) with a 21 W bulb → Terminal 2
Battery negative (-) → Terminal 1
Valve moves and makes an operating noise
Text in Illustration
*a
Component without harness connected
(Shift Solenoid Valve SLT)
NG
REPLACE SHIFT SOLENOID VALVE SLT
OK
INSPECT TRANSMISSION VALVE BODY ASSEMBLY
NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY
OK
INSPECT TORQUE CONVERTER ASSEMBLY
(a) Check the torque converter assembly (See page ).