DESCRIPTION
The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the ECM.
DTC Code | DTC Detection Condition | Trouble Area |
P0705 |
One of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2-trip detection logic):
- One of the following conditions is met.
- P input signal is ON
- N input signal is ON
- NSW input signal is ON
- R input signal
- D input signal
(B) Any of the following signals is ON for 2.0 seconds or more with the shift lever in S (2-trip detection logic):
- P input signal
- N input signal
- NSW input signal
- R input signal
(C) All signals are OFF simultaneously for P, R, N and D positions (2-trip detection logic). |
- Open or short in park/neutral position switch circuit
- Park/neutral position switch
- Transmission control switch (Column shift shift lever sub-assembly)*1
- Transmission control switch (Transmission floor shift assembly)*2
- ECM
|
HINT:
- *1: for Column Shift Type
- *2: for Floor Shift Type
MONITOR DESCRIPTION
This DTC indicates a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N, D or S).
The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.
MONITOR STRATEGY
Related DTCs |
P0705: Park/neutral position switch/Verify switch input |
Required sensors/Components |
Park/neutral position switch |
Frequency of operation |
Continuous |
Duration |
Condition (A) and (B)
2 seconds
Condition (C)
60 seconds |
MIL operation |
2 driving cycles |
Sequence of operation |
None |
TYPICAL ENABLING CONDITIONS All
The monitor will run whenever the following DTCs are not present |
None |
Battery voltage |
8 V or more |
Ignition switch |
ON |
Starter |
OFF |
TYPICAL MALFUNCTION THRESHOLDS
- One of the following conditions is met: Condition (A), (B) or (C) Condition (A)
- When 2 or more of the following signals are input at the same time
One of the following conditions is met
P switch
N switch
NSW switch |
ON |
R switch |
ON |
D switch |
ON |
Condition (B)
- When the shift lever is in S, one of the following conditions is met
P switch |
ON |
N switch |
ON |
NSW switch |
ON |
R switch |
ON |
Condition (C)
- All of the following conditions are met
P switch |
OFF |
N switch |
OFF |
NSW switch |
OFF |
R switch |
OFF |
D switch |
OFF |
COMPONENT OPERATING RANGE
Park/neutral position switch |
The park/neutral position switch sends only one signal to the ECM |
WIRING DIAGRAM
NOTICE:
Perform the universal trip to clear permanent DTCs (See page ).
1. DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the Techstream to the DLC3.
(d) Turn the ignition switch to ON.
(e) Turn the Techstream on.
(f) Enter the following menus: Powertrain / Engine and ECT / Data List.
(g) According to the display on the Techstream, read the Data List. Engine and ECT:
Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
Neutral Position SW Signal |
PNP switch status/
ON or OFF |
- Shift lever in P or N: ON
- Shift lever not in P or N: OFF
|
When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
Shift SW Status (P Range) |
PNP switch status/
ON or OFF |
- Shift lever in P: ON
- Shift lever not in P: OFF
|
When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
Shift SW Status (R Range) |
PNP switch status/
ON or OFF |
- Shift lever in R: ON
- Shift lever not in R: OFF
|
When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
Shift SW Status (N Range) |
PNP switch status/
ON or OFF |
- Shift lever in N: ON
- Shift lever not in N: OFF
|
When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
Sports Shift Up SW |
Sport shift up switch status/
ON or OFF |
- ON: Shift lever held in "+" (up-shift)
- OFF: Shift lever not held in "+" (up-shift)
|
- |
Sports Shift Down SW |
Sport shift down switch status/
ON or OFF |
- ON: Shift lever held in "-" (down-shift)
- OFF: Shift lever not held in "-" (down-shift)
|
- |
Sports Mode Selection SW |
Sport mode select switch status/
ON or OFF |
- ON: Shift lever in S, "+" or "-"
- OFF: Shift lever not in S, "+" or "-"
|
- |
Shift SW Status (D Range) |
PNP switch status/
ON or OFF |
- Shift lever in D, S, "+" or "-": ON
- Shift lever not in D, S, "+" or "- ": OFF
|
When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
PROCEDURE
INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
(a) Disconnect the D35 park/neutral position switch connector. |
 |
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
- 2 (RB) - 6 (PL)
- 4 (B) - 5 (L)
|
Shift lever in P |
Below 1 Ω |
2 (RB) - 1 (RL) |
Shift lever in R |
Below 1 Ω |
- 2 (RB) - 9 (NL)
- 4 (B) - 5 (L)
|
Shift lever in N |
Below 1 Ω |
2 (RB) - 7 (DL) |
Shift lever in D, S, "+" or "-" |
Below 1 Ω |
- 2 (RB) - 6 (PL)
- 4 (B) - 5 (L)
|
Shift lever not in P |
10 kΩ or higher |
2 (RB) - 1 (RL) |
Shift lever not in R |
10 kΩ or higher |
- 2 (RB) - 9 (NL)
- 4 (B) - 5 (L)
|
Shift lever not in N |
10 kΩ or higher |
2 (RB) - 7 (DL) |
Shift lever not in D, S, "+" or "-" |
10 kΩ or higher |
Text in Illustration
*a |
Component without harness connected
(Park/Neutral Position Switch) |
| NG |
 |
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
| OK |
 |
|
INSPECT TRANSMISSION CONTROL SWITCH
(a) for Column Shift Type:
(1) Disconnect the J25 transmission control switch connector.
(2) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
6 (IG) - 13 (S) |
Shift lever in S, "+" or "-" |
Below 1 Ω |
6 (IG) - 13 (S) |
Shift lever not in S, "+" or "-" |
10 kΩ or higher |
Text in Illustration
*a |
Component without harness connected
(Transmission Control Switch) |
|
 |
(b) for Floor Shift Type:
(1) Disconnect the J24 transmission control switch connector.
(2) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
3 (IG) - 7 (S) |
Shift lever in S, "+" or "-" |
Below 1 Ω |
3 (IG) - 7 (S) |
Shift lever not in S, "+" or "-" |
10 kΩ or higher |
Text in Illustration
*a |
Component without harness connected
(Transmission Control Switch) |
Result
Result | Proceed to |
OK |
A |
NG (for Column Shift Type) |
B |
NG (for Floor Shift Type) |
C |
|
 |
| B |
 |
REPLACE TRANSMISSION CONTROL SWITCH (COLUMN SHIFT SHIFT LEVER SUB-ASSEMBLY) |
| C |
 |
REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY) |
| A |
 |
|
CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)
(a) Disconnect the D35 park/neutral position switch connector. |
 |
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Switch Condition | Specified Condition |
D35-2 (RB) - Body ground |
Ignition switch ON |
11 to 14 V |
D35-2 (RB) - Body ground |
Ignition switch off |
Below 1 V |
Text in Illustration
*a |
Front view of wire harness connector
(to Park/Neutral Position Switch) |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH - IGNITION SWITCH) |
| OK |
 |
|
CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE)
(a) for Column Shift Type:
(1) Disconnect the J25 transmission control switch connector.
(2) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Switch Condition | Specified Condition |
J25-6 (IG) - Body ground |
Ignition switch ON |
11 to 14 V |
J25-6 (IG) - Body ground |
Ignition switch off |
Below 1 V |
Text in Illustration
*a |
Front view of wire harness connector
(to Transmission Control Switch) |
|
 |
(b) for Floor Shift Type:
(1) Disconnect the J24 transmission control switch connector.
(2) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Switch Condition | Specified Condition |
J24-3 (IG) - Body ground |
Ignition switch ON |
11 to 14 V |
J24-3 (IG) - Body ground |
Ignition switch off |
Below 1 V |
Text in Illustration
*a |
Front view of wire harness connector
(to Transmission Control Switch) |
|
 |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - IGNITION SWITCH) |
| OK |
 |
|
CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
(a) Disconnect the D74 ECM connector. |
 |
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
- D74-2 (P) - Body ground
- D74-120 (NSW) - Body ground
|
- Ignition switch ON
- Shift lever in P
|
11 to 14 V |
D74-26 (R) - Body ground |
- Ignition switch ON
- Shift lever in R
|
11 to 14 V* |
- D74-25 (N) - Body ground
- D74-120 (NSW) - Body ground
|
- Ignition switch ON
- Shift lever in N
|
11 to 14 V |
D74-27 (D) - Body ground |
- Ignition switch ON
- Shift lever in D
|
11 to 14 V |
- D74-2 (P) - Body ground
- D74-120 (NSW) - Body ground
|
- Ignition switch ON
- Shift lever not in P
|
Below 1 V |
D74-26 (R) - Body ground |
- Ignition switch ON
- Shift lever not in R
|
Below 1 V |
- D74-25 (N) - Body ground
- D74-120 (NSW) - Body ground
|
- Ignition switch ON
- Shift lever not in N
|
Below 1 V |
D74-27 (D) - Body ground |
- Ignition switch ON
- Shift lever not in D
|
Below 1 V |
Text in Illustration
*a |
Front view of wire harness connector
(to ECM) |
HINT:
*: The voltage will drop slightly due to the illumination of the back-up light.
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
| OK |
 |
|
CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
(a) Disconnect the A24 ECM connector. |
 |
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
A24-25 (S) - Body ground |
Shift lever in S, "+" or "-" |
11 to 14 V |
A24-25 (S) - Body ground |
Shift lever not in S, "+" or "-" |
Below 1 V |
Text in Illustration
*a |
Front view of wire harness connector
(to ECM) |
| OK |
 |
REPLACE ECM |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|