Toyota Venza: On-vehicle Inspection

ON-VEHICLE INSPECTION PROCEDURE

1. INSPECT REFRIGERANT PRESSURE WITH MANIFOLD GAUGE SET

HINT:

This is a method where a manifold gauge set is used to help locate the problem.

(a) Read the manifold gauge pressure when the following conditions are met:

Test conditions:

(1) Normally functioning refrigeration system

Gauge Reading

Pressure Side	Refrigerant Volume
Low	150 to 250 kPa (1.5 to 2.5 kgf/cm2, 22 to 36 psi)
High	1370 to 1570 kPa (14.0 to 16.0 kgf/cm2, 199 to 228 psi)

(2) Moisture is present in the refrigeration system.

Symptom	Probable Cause	Diagnosis	Corrective Action
During operation, pressure on low pressure side cycles between normal and vacuum	Moisture in the AC system will freeze at the expansion valve orifice, causing the refrigeration cycle to temporarily stop After the system stops, and warms up again, the ice will melt and normal operation will be temporarily restored	Cooler dryer (integrated into condenser tank) in oversaturated state Moisture in refrigeration system freezes at expansion valve orifice and blocks circulation of refrigerant	1 Replace cooler dryer 2 Remove moisture in system by repeatedly evacuating air 3 Supply a proper amount of new refrigerant

(3) Insufficient cooling

Symptom	Probable Cause	Diagnosis	Corrective Action
Pressure is low on both low and high pressure sides Bubbles are seen through sight glass continuously Insufficient cooling performance	Gas leaks from the refrigeration system	Insufficient refrigerant Refrigerant leaking	1 Check for gas leaks and repair if necessary 2 Supply a proper amount of new refrigerant 3 If the gauge indicates a pressure of close to 0, then it will be necessary to evacuate the system after repairing the leak

(4) Poor circulation of refrigerant

Symptom	Probable Cause	Diagnosis	Corrective Action
Pressure is low on both low and high pressure sides Frost exists on pipe from condenser to unit	Refrigerant flow is obstructed by dirt inside the pipes of the condenser core	Receiver is clogged	Replace condenser

(5) Refrigerant does not circulate.

Symptom	Probable Cause	Diagnosis	Corrective Action
Vacuum is indicated on low pressure side and very low pressure is indicated on high pressure side Frost or condensation is seen on piping on both sides of receiver/drier or expansion valve	Refrigerant flow is obstructed by moisture or dirt in refrigeration system Refrigerant flow is disrupted by gas leaks internally through the expansion valve	Refrigerant does not circulate	1 Check expansion valve 2 Replace expansion valve 3 Replace condenser 4 Evacuate air and supply a proper amount of new refrigerant 5 For internal gas leaks at expansion valve, replace expansion valve

(6) Refrigerant is overcharged or cooling effectiveness of condenser is insufficient.

Symptom	Probable Cause	Diagnosis	Corrective Action
Pressure is too high on both low and high pressure sides No air bubbles are seen through sight glass even when engine rpm lowers	Unable to develop sufficient performance due to excessive use of refrigeration system Cooling effectiveness of condenser is insufficient	Excessive refrigerant in cycle → excessive refrigerant was added during recharging Condenser cooling effectiveness is insufficient → condenser fins are clogged at cooling fan	1 Clean condenser 2 Check the operation of the condenser cooling fan 3 If 1 and 2 are normal state, check the amount of refrigerant and supply a proper amount of refrigerant

(7) Air is present in the refrigeration system.

Symptom	Probable Cause	Diagnosis	Corrective Action
Pressure is too high on both low and high pressure sides The low pressure piping is too hot to touch Bubbles can be seen through sight glass	Air in system	Air present in refrigeration system Insufficient vacuum purging	1 Check compressor oil to see if it is dirty or insufficient 2 Evacuate the system and recharge it with new or purified refrigerant

(8) Expansion valve malfunction

Symptom	Probable Cause	Diagnosis	Corrective Action
Pressure is too high on both low and high pressure sides Frost or a large amount of condensation on piping on low pressure side	Expansion valve may be stuck	Excessive refrigerant in low pressure piping Expansion valve opened too wide	Check expansion valve

(9) Insufficient compressor compression

Symptom	Probable Cause	Diagnosis	Corrective Action
Pressure is too high on both low and high pressure sides Pressure is too low on high pressure side	Internal leak in compressor	Low compression Leak from a damaged valve, or parts may be broken	Replace compressor

Gauge readings (Reference)

On-vehicle Inspection