Electrical System General Information

Tool descriptions

~3min read

Stop crimping pliers with insert

The stop crimping pliers without insert -VAS 1978/1-, with the insert for stop crimping pliers -VAS 1978/2-, is part of the wiring harness repair set -VAS 1978- and is used to crimp the crimp connectors during wiring harness repair.

VW UP. Elektrische Anlage Allgemeine Informationen



Note

  • Alternatively, the crimping pliers (basic body) -VAS 1978/1-2- can be used to crimp the connectors in combination with the interchangeable heads -VAS 1978/1-1- or -VAS 1978/2A-.
  • Be sure to use the correct crimping jaw for the crimp connector being used.
  • The wire insulation must not be crimped.

Release tools for contacts

The various release tools are used to remove the different contacts from the contact housings without damage.

A selection of release tools is part of the wiring harness repair set -VAS 1978- and the wiring harness repair set -VAS 1978A-. The complete set of release tools is contained in the release tool set -VAS 1978/35-.


WARNING!

Some tools have a tool safety clip. After using the tool, slide it over the tool tip to protect the technician from injury and the tool tip from damage.

Releasing and disassembling contact housings.

VW UP. Elektrische Anlage Allgemeine Informationen

Assembly tools for individual wire seals

The assembly tools are used to push the individual wire seals into the contact housing up to the stop without damaging them, in order to achieve complete sealing between the individual wire and the contact housing.

Four assembly tools for individual wire seals are each part of the wiring harness repair set -VAS 1978 B- and its predecessors.

Installing individual wire seals.

VW UP. Elektrische Anlage Allgemeine Informationen

Wire stripper -VAS 1978/3-

The wire stripping pliers -VAS 1978/3- are used to strip and cut wires correctly.

The wire stripping pliers -VAS 1978/3- are part of the Wiring Harness Repair Kit -VAS 1978 B- and its predecessors.

The jaws of the wire stripping pliers have an adjustable stop that is used to set the required length of wire insulation to be removed.

Stripping wire insulation:

- Set the adjustable stop in the jaws to the required stripping length.

VW UP. Elektrische Anlage Allgemeine Informationen

- Insert the wire end from the front into the jaws up to the stop and squeeze the pliers fully closed.

- Open the pliers again and remove the stripped wire end.

VW UP. Elektrische Anlage Allgemeine Informationen

- If necessary, cut wires using the side cutter function on the top of the wire stripping pliers.

VW UP. Elektrische Anlage Allgemeine Informationen

Hot air blower, 220 V/ 50 Hz -VAS 1978/14-


Caution!

When shrinking the crimp connectors, make sure the hot nozzle of the hot air blower does not damage other wires, plastic parts or insulation material.

Be sure to observe the operating instructions for the hot air blower!

The hot air blower, 220 V/ 50 Hz -VAS 1978/14- is used together with the hot air blower shrink attachment -VAS 1978/15- to shrink the crimp connectors. After crimping, the crimp connector must be shrunk with the hot air blower to prevent moisture from entering.

The hot air blower, 220 V/ 50 Hz -VAS 1978/14- is part of the Wiring Harness Repair Kit -VAS 1978 B- and its predecessors.

Shrink the crimp connector using the hot air blower, 220 V/ 50 Hz -VAS 1978/14-, or.

VW UP. Elektrische Anlage Allgemeine Informationen

Crimping pliers -VAS 1978/1A-

The crimping pliers -VAS 1978/1A- or the crimping pliers (basic tool) -VAS 1978/1-2- together with the interchangeable head 0.35-2.5 mm2 -VAS 1978/1-1-, or the interchangeable head 4.0-6.0 mm2 -VAS 1978/2A- are used to crimp the crimp connectors from the wiring harness repair kits.

Crimping the crimp connectors with the crimping pliers -VAS 1978/1A-.

The following interchangeable heads are available for the crimping pliers (basic tool) -VAS 1978/1-2-:

  • Interchangeable head 0.35 mm 2 - 2.5 mm 2 -VAS 1978/1-1-
  • Interchangeable head 4.0 mm 2 - 6.0 mm 2 -VAS 1978/2A-
  • Interchangeable head JPT contact -VAS 1978/9-1-

Together with the interchangeable head JPT contact -VAS 1978/9-1-, the crimping pliers are used to crimp contacts onto individual wires when repairing wire cross-sections up to 0.35 mm 2.

Replacing the interchangeable head:

- Open the crimping pliers fully.

VW UP. Elektrische Anlage Allgemeine Informationen

- Release the two locking pins -arrows- from the basic tool of the crimping pliers.

VW UP. Elektrische Anlage Allgemeine Informationen

- Insert the required interchangeable head from above -arrow- into the basic tool of the crimping pliers.

VW UP. Elektrische Anlage Allgemeine Informationen

- Lock the interchangeable head by pressing the pins -arrows- into the basic tool of the crimping pliers.

VW UP. Elektrische Anlage Allgemeine Informationen