Front seats

Before moving the seat rearward, check that nothing and no one is obstructing the seat's travel.

Risk of pinching if passengers are in the rear, or of the seat jamming if bulky objects are placed on the floor behind the seat.

Manual seats

Fore-aft

► lift the control bar and slide the seat forward or rearward.

► release the control bar to lock the seat in one of the detent positions.

Backrest recline

► turn the wheel to obtain the desired seatback recline.

Lumbar support

(driver only)

► turn the wheel to obtain the desired lumbar support.

Height

► pull the control up to raise, or push it down to lower, until the desired position is reached.

Power seats

To avoid discharging the battery, make these adjustments with the engine running.

Fore-aft

► push the control forward or rearward to slide the seat.

Backrest recline

► tilt the control forward or rearward.

Lumbar support

The control allows the depth and height of the lumbar support to be adjusted independently.

► hold the front or rear of the control to increase or decrease the lumbar support.

► hold the top or bottom of the control to raise or lower the lumbar support zone.

Seat cushion height and tilt

► tilt the rear of the control up or down to obtain the desired height.

► tilt the front of the control up or down to obtain the desired tilt.

Comfort functions

Driving position memory

Used with the power driver's seat, this function stores two driving positions to make adjustments easier when drivers change frequently.

It stores the power seat and outside mirror settings.

Using the 1 / 2 / M buttons

► get in and switch the ignition on.

► adjust the seat and outside mirrors.

► press button M, then within 4 seconds, press button 1 or 2.

An audible signal sounds to confirm the position has been stored.

Storing a new position overwrites the previous one.

Recalling a stored position

When the seat is moving, make sure nothing and no one is obstructing its automatic movement.

Ignition on or engine running

► press button 1 or 2 to recall the corresponding position.

An audible signal sounds when the recall is complete. It is possible to interrupt the movement in progress by pressing button M, 1 or 2, or by using a seat adjustment control.

Position recall is not possible while driving.

Position recall is disabled approximately 45 seconds after the ignition is switched off.

Heated seats

The function is only active with the engine running and when the outside temperature is below 20 °C.

► press the button for the corresponding seat.

► each press changes the heating level; the corresponding number of indicator lights comes on.

► to turn the heating off, press the button until all indicator lights go out.

The status of the function is stored when the ignition is switched off.

Do not use the function when the seat is unoccupied.

Reduce the heating level as soon as possible.

Once the seat and cabin temperatures have reached a sufficient level, turn the function off; lower current draw reduces energy consumption.

Prolonged use of the seat heaters is not recommended for people with sensitive skin.

Risk of burns for people with impaired heat perception (e.g. due to illness or medication).

To maintain the integrity of the heating element and prevent the risk of short circuit:

- Do not place heavy or sharp objects on the seat.

- Do not kneel or stand on the seat.

- Do not pour in any liquids.

- Never use the function while the seat cushion is soaked.

Multi-point massage

System with choice of massage type and adjustment of its intensity.

This system operates with the engine running, as well as in Stop mode of the Stop & Start system.

Massage settings are made using the touchscreen.

The function is activated using the front seat button.

► Press this button; its indicator light comes on.

The function starts immediately with the last stored settings, and the settings page is displayed on the touchscreen.

If the settings are suitable, the display returns to its initial state if no action is taken.

To change the settings: ► Select a different massage type from the five available.

► Select a massage intensity from the three preset levels: "1" (Low), "2" (Normal) or "3" (High).

Changes take effect immediately.

Once activated, the system starts a one-hour massage cycle, made up of 6-minute massage sequences followed by 4-minute pauses.

The system stops automatically at the end of the cycle; the button indicator light goes out.

Steering wheel adjustment

► When stationary, pull control A to unlock the steering wheel.

► Adjust the height and reach to suit your driving position.

► Push the control to lock the steering wheel.

For safety reasons, these adjustments must be made only with the vehicle stationary.