Motor and Reduction Gear System
Front Motor and Reduction Gear System
In this manual: Motor and Reduction Gear System
74steps
~444min
4/5difficulty
Done 0 of 74
Contents:
Front Under Cover Removal and Installation
Removal
Front Under Cover- Remove the front under cover (A) after removing the fasteners and bolts.
Tightening torque : 7.8 - 11,8 N·m
| When installing the lift jack, verify that the lift jack (A) and the front rear under cover (B) do not interfere. |
- Remove the engine room under rear cover (A) after removing the fasteners, nuts and bolts.
Tightening torque : 7.8 - 11,8 N·m
Installation
Front Under Cover- Install in the reverse order of removal.
- Install in the reverse order of removal.
Front Motor Cover Removal and Installation
Removal
|
- Shut off the high voltage circuit. (Refer to Motor and Reduction Gear System - "High Voltage Shut-off Procedures")
- Remove the front trunk. (Refer to Body - "Front Trunk")
- Drain the coolant. (Refer to Electric Vehicle Cooling System - "Coolant")
- Remove the motor & reduction gear oil cooler. (Refer to Cooling System - "Motor & Reduction Gear Oil Cooler")
- Remove the coolant distribution pipe. (Refer to Cooling System - "Coolant Distribution Pipe")
- Remove the front motor front cover (A) after removing the fasteners.
- Shut off the high voltage circuit. (Refer to Motor and Reduction Gear System - "High Voltage Shut-off Procedures")
- Remove the front trunk. (Refer to Body - "Front Trunk")
- Remove the front motor side cover (A) after removing the fasteners.
- Shut off the high voltage circuit. (Refer to Motor and Reduction Gear System - "High Voltage Shut-off Procedures")
- Remove the front trunk. (Refer to Body - "Front Trunk")
- Remove the electric A/C compressor. (Refer to Heating,Ventilation And Air Conditioning - "Electric A/C Compressor")
- Remove the front reduction gear front cover (A) after removing the fasteners.
- Remove the front under cover. (Refer to Front Motor and Reduction Gear System - "Front Under Cover")
- Remove the front motor rear cover 1 (A) after removing the fasteners.
- Shut off the high voltage circuit. (Refer to Motor and Reduction Gear System - "High Voltage Shut-off Procedures")
- Remove the front trunk. (Refer to Body - "Front Trunk")
- Remove the front under cover. (Refer to Front Motor and Reduction Gear System - "Front Under Cover")
- Drain the coolant. (Refer to Electric Vehicle Cooling System - "Coolant")
- Remove the battery heater. (Refer to Cooling System - "Battery Heater")
- Remove the wiring mounting bolt (A).
Tightening torque : 6.9 - 9,8 N·m
- Remove the front motor rear cover 2 (A) after removing the fasteners.
Installation
Front Motor Front Cover- Install in the reverse order of removal.
- Install in the reverse order of removal.
- Install in the reverse order of removal.
- Install in the reverse order of removal.
- Install in the reverse order of removal.
Front Motor and Reduction gear Mounting Components and Components Location
Components and Components Location
| 1. LH Motor Mounting Bracket 1-a. 107.9 - 128 N·m 1-b. 63.7 - 83 N·m 2. RH Motor Mounting Bracket 2-a. 107.9 - 128 N·m 2-b. 63.7 - 83 N·m |
3. RR Motor Mounting Bracket 3-a. 107.9 - 128 N·m 3-b. 63.7 - 83 N·m |
Front Motor and Reduction gear Mounting Removal and Installation
Special Service Tool
| Tool Name / Number | Illustration | Description |
| Engine fixture (adapter) 09200 - 4X000 |
Used for anchoring the motor and reducer gear when removing and installing the motor and reducer gear |
Removal
LH Motor Mounting Bracket- Remove the front motor and reduction gear assembly. (Refer to Front Motor and Reduction Gear System - "Front Motor and Reduction Gear Assembly")
- Support the motor and reduction gear assembly using engine cranes and SST (09200 - 4X000).
Install the SST (09200 - 4X000) to the front motor and reduction gear assembly hangers. - Remove the motor mounting bracket bolts and nuts (A).
Tightening torque : 107.9 - 128 N·m
- Remove the front motor and reduction gear assembly from the front subframe by lifting the engine crane upwards.
- Be careful not to damage the high voltage connector.
- Be careful not to damage the parts of the motor and reduction gear assembly.
- Remove the LH motor mounting bracket (A) after removing the mounting bolts.
Tightening torque : 63.7 - 83 N·m
- Remove the front motor and reduction gear assembly. (Refer to Front Motor and Reduction Gear System - "Front Motor and Reduction Gear Assembly")
- Support the motor and reduction gear assembly using engine cranes and SST (09200 - 4X000).
Install the SST (09200 - 4X000) to the front motor and reduction gear assembly hangers. - Remove the RH motor mounting bracket bolt and nut (A).
Tightening torque : 107.9 - 128 N·m
- Remove the RH motor mounting bracket (A) after removing the mounting bolts.
Tightening torque : 63.7 - 83 N·m
- Remove the front motor and reduction gear assembly. (Refer to Front Motor and Reduction Gear System - "Front Motor and Reduction Gear Assembly")
- Support the motor and reduction gear assembly using engine cranes and SST (09200 - 4X000).
Install the SST (09200 - 4X000) to the front motor and reduction gear assembly hangers. - Remove the RR motor mounting bolt and nut (A).
Tightening torque : 107.9 - 128 N·m
- Remove the RR motor mounting bracket (A) after removing the mounting bolts.
Tightening torque : 63.7 - 83 N·m
Installation
LH Motor Mounting Bracket- Install in the reverse order of removal.
- Install in the reverse order of removal.
- Install in the reverse order of removal.
Front Motor and Reduction Gear Assembly Components and Components Location
Components and Components Location
| 1. Motor & Reduction Gear Oil Cooler 1-a. 6.9 - 9,8 N·m 2. Coolant Distribution Pipe 2-a. 16.7 - 24 N·m 3. Front Motor Front Cover 4. Electronic Oil Pump (EOP) 4-a. 19.6 - 26 N·m 5. O-ring 6. LH motor Mounting Bracket 6-a. 63.7 - 83 N·m 7. Motor Side Mounting Bracket 7-a. 60.8 - 80 N·m 8. Motor Position and Temperature Sensor 8-a. 9.8 - 11,8 N·m 9. Front Motor Side Cover |
10. Disconnect Actuator System (DAS) Motor 10-a. 4.9 - 5,9 N·m (0.5 - 0.6 kgf·m, 3.6 - 4.3 lb·ft, 43.4 - 52.1 lb·in) 11. O-ring 12. Oil Temperature Sensor 12-a. 9.8 - 11,8 N·m 13. Tube Pipe 13-a. 9.8 - 11,8 N·m 13-b. 41.2 - 47 N·m 14. Tube Pipe Washer 15. RR Motor Mounting Bracket 15-a. 63.7 - 83 N·m 16. Front Motor Rear Cover 2 17. Front Motor Rear Cover 1 18. Inverter Assembly 18-a. 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in) 19. Inverter Assembly Gasket 20. Front Motor and Reduction Gear Assembly |
Front Motor and Reduction Gear Assembly Removal ➤
Front Motor and Reduction Gear Assembly Installation
Installation
- Install in the reverse order of removal.
Make sure the quick connector is installed securely after installing the coolant hose. [Type A] - Make sure the quick connector (A) is installed securely. [Type B] - Make sure the quick connector and quick connector clamp are installed securely. - Make sure that the quick connector protrusion (A) fits into the groove (B). - Fill with coolant. (Refer to Electric Vehicle Cooling System - "Coolant")
Using the KDS, perform Electric Water Pump (EWP) air bleeding. - Refill the front motor and reduction gear oil. (Refer to Front Motor and Reduction Gear System - "Front Motor and Reduction Gear Oil")
Do not fill oil when replacing the motor and reduction gear with new ones. - After installing the front motor and reduction gear assembly, perform the leakage test. (Refer to Battery Control System - "Air Tightness")
- Perform the "Motor Control Unit-Front" and "Initialization of Automatic Resolver Offset Calibration" using the KDS. (Refer to Motor and Reduction Gear System - Motor Position & Temperature Sensor)
If the resolver offset correction initialization is not performed, the output may be reduced and the drivable distance may be shortened.
Front Motor and Reduction Gear Assembly On Vehicle Inspection
Inspection
[Phase Resistance]- Remove the front high voltage junction box. (Refer to Battery Control System - "Front High Voltage Junction Box")
- Remove the inverter assembly. (Refer to Battery Control System - "Inverter Assembly - 4WD")
- Check the resistance of each line (U, V, W) using a milliohm meter.
Item Inspection part Specifications Remark Phase resistance
(Line - Line)U - V 168.63 - 186.38mΩ Reference temperature : 20 °C V - W W - U - Remove the front high voltage junction box. (Refer to Battery Control System - "Front High Voltage Junction Box")
- Remove the inverter assembly. (Refer to Battery Control System - "Inverter Assembly - 4WD")
- Check insulation resistance using an insulation resistance tester.
- Connect the ( - ) terminal of insulation resistance tester to housing.
- Connect the ( + ) terminal of the insulation resistance tester to the 3-phase (U, V, W).
- Apply DC 1,000 V power for 1 minute and check the measured value.
Item Inspection area Specifications Remark Insulation resistance Housing - U 100MΩ or more DC 1,000 V, 1 minute Housing - V Housing - W
- Remove the front high voltage junction box. (Refer to Battery Control System - "Front High Voltage Junction Box")
- Remove the inverter assembly. (Refer to Battery Control System - "Inverter Assembly - 4WD")
- Check leakage current Using a withstanding voltage tester.
- Connect the ( - ) terminal of withstand voltage tester to housing.
- Connect the ( + ) terminal of withstand voltage tester to 3-phase (U, V, W).
- Check the measured value by applying AC 2,200 V for one minute.
Item Inspection area Specifications Remark Dielectric strength Housing - U 10mA_rms or less AC 2,200 V, 1minute Housing - V Housing - W
Front Motor and Reduction Gear Oil Replacement
Replacement
|
| When checking the reduction gear oil level, be careful not to allow foreign substance (like dust) to enter through the filler hole. |
- Remove the front under cover. (Refer to Front Motor and Reduction Gear System - "Front Under Cover")
- Prepare a clean 5 ℓ beaker (A) to measure the amount of oil.
- Remove the drain plug (A) and drain oil, and then reinstall the drain plug.
Tightening torque : 44.1 - 59 N·m
The existing drain plug gasket (A) must be replaced with a new one (do not reuse). - Remove the front reduction gear cover fastener (A).
- Remove the filler plug (A).
- Fill the specified oil through the filler plug hole as much as it has been drained.
Recommended : Kia genuine ATF SP4M-1
- Install the filler plug (A).
Tightening torque : 44.1 - 59 N·m
The existing filler plug gasket (A) must be replaced with a new one (do not reuse). - Install the front reduction gear cover fastener (A).
- Install the front under cover. (Refer to Front Motor and Reduction Gear System - "Front Under Cover")
Front Motor and Reduction Gear Oil Seal Replacement
Special Service Tool
| Tool Name / Number | Illustration | Description |
| Reduction gear oil seal installer 09445 - GI100 |
Installation of the oil seal on the Front reduction gear case and housing (Used with the handle) |
|
| Handle 09231 - H1100 |
Used with the oil seal installer |
Replacement
|
- Drain the front motor and reduction gear oil. (Refer to Front Motor and Reduction Gear System - "Front Motor and Reduction Gear Oil")
- Remove the front driveshaft assembly. (Refer to Driveshaft Assembly - "Front Driveshaft")
- Remove the oil seal (A). Case side Housing side
- When installing a new oil seal, use the SST (09445 - GI100, 09231 - H1100). Case side Housing side
- Install the front driveshaft assembly. (Refer to Driveshaft Assembly - "Front Driveshaft")
- Refill the front motor and reduction gear oil. (Refer to Front Motor and Reduction Gear System - "Front Motor and Reduction Gear Oil")
Was this page helpful?