Motor and Reduction Gear System

Rear Motor and Reduction Gear System

73steps
~438min
4/5difficulty
010203040505.94N·mlb·ft
Tightening torque found on this page
Done 0 of 73

Contents:

Rear Under Cover Removal and Installation

Removal

Center Floor Rear Under Cover
  1. Remove the center floor rear under cover (A) after removing the mounting nuts.
    Tightening torque : 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
    [Standard] [Long Range]
  2. Remove the rear cross member under cover (A) after removing the mounting bolts.
    Tightening torque : 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
Rear Cross Member under Cover

Installation

Center Floor Rear Under Cover
  1. Install in the reverse order of removal.
  2. Install in the reverse order of removal.
Rear Cross Member under Cover

Rear Motor Cover Removal and Installation

Removal

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working a high-voltage system, the technician must recognize and observe "General Safety Information and Caution". If not, serious accidents like electric shocks and short circuits may be caused.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Rear Motor Center Cover
  1. Remove the rear cross member under cover. (Refer to Rear Motor and Reduction Gear System - "Rear Under Cover")
  2. Remove the rear cross member under cover braket (A) after removing the bolts.

    Tightening torque : 117.7 - 137 N·m

  3. Remove the rear motor and reduction gear oil cooler. (Refer to Cooling System - "Motor and Reduction Gear Oil Cooler" )
  4. Remove the rear motor center cover (A) after removing the fasteners.
  5. Remove the RH rear driveshaft & axle assembly. (Refer to Driveshaft and Axle - "Integrated Drive Axle (IDA)")
  6. Remove the rear motor reduction gear cover (A) after removing the fasteners.
Rear Motor Reduction Gear Cover

Installation

  1. Install in the reverse order of removal.

Rear Motor and Reduction Gear Mounting Removal and Installation. Rear Motor and Reduction Gear Assembly Components and Components Location

Rear Motor and Reduction Gear Mounting Removal and Installation

Removal

RH Motor Mounting Bracket
  1. Remove the rear under cover. (Refer to Rear Motor and Reduction Gear System - "Rear Under Cover")
  2. Support the underside of the rear motor and reduction gear assembly with a jack (A).
    Place the rubber block between the rear motor and reduction gear assembly and the jack to prevent damage.
  3. Remove the RH motor mounting bracket (A) after removing the bolts (B) and bolt and nut (C).
    Tightening torque B : 63.7 - 83 N·m C : 107.9 - 128 N·m

Installation

RH Motor Mounting Bracket
  1. Install in the reverse order of removal.

Rear Motor and Reduction Gear Assembly Components and Components Location

Components and Components Location

1. Water Hose Assembly
2. Rear High Voltage Junction Box
2-a. 9.8 - 11,8 N·m
3. Multi Inverter Assembly
3-a. 4.0 - 5,8 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.0 lb·in)
4. Multi Inverter Assembly Gasket
5. SBW(Shift By Wire) Actuator
5-a. 20.6 - 28 N·m
6. Motor Position and Temperature Sensor
6-a. 9.8 - 11,8 N·m
7. Motor and Reduction Gear Oil Cooler Cooling Hose
8. Motor and Reduction Gear Oil Cooler
8-a. 6.9 - 9,8 N·m
9. Rear Motor Cover
10. Tube Pipe B
10-a. 41.2 - 47 N·m
11. Tube Pipe B Gasket
12. Tube Pipe A
12-a. 41.2 - 47 N·m
13. Tube Pipe A Gasket
14. RH Motor Mounting Bracket
14-a. 63.7 - 83 N·m
15. Rear Motor Side Cover
16. Electronic Oil Pump (EOP)
16-a. 19.6 - 26 N·m
17. O-ring
18. Rear Motor and Reduction Gear Assembly

Rear Motor and Reduction Gear Assembly Removal

Special Service Tool

Tool Name / Number Illustration Description
Engine fixture (adapter)
09200 - 4X000
Used for anchoring the motor and reducer gear when removing and installing the motor and reducer gear

Removal

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working a high-voltage system, the technician must recognize and observe "General Safety Information and Caution". If not, serious accidents like electric shocks and short circuits may be caused.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  • Use a fender cover to protect the painted surface.
  • Be careful not to damage the connector when disconnecting.
  • When disconnecting a quick connector, refer to the following according to the type of quick connector. [Type A] - Remove while pressing the quick connector clamp (A) in the direction of the arrow. - Do not touch the rubber seal (B) inside the hose. [Type B] - Pull the quick connector clamp (A) in the direction of the arrow to separate the clamp and remove the hose. - Do not touch the rubber seal (B) inside the hose.
Mark all wiring and hoses to prevent incorrect connections.
  1. Shut off the high voltage circuit. (Refer to Motor and Reduction Gear System - "High Voltage Shut-off Procedures")
  2. Remove the rear seat assembly. (Refer to Body - "Rear Seat Assembly")
  3. Remove the luggage side trim. (Refer to Body - "Luggage Side Trim")
  4. Remove the luggage floor board (A).
  5. Remove the fast charge connector service cover (A) after removing the nuts.

    Tightening torque : 7.8 - 11,8 N·m

  6. Disconnect charge connector (A) after removing the bolt.

    Tightening torque : 9.8 - 10,8 N·m

  7. Remove the rear under cover. (Refer to Rear Motor and Reduction Gear System - "Rear Under Cover")
  8. Drain the motor coolant. (Refer to Electric Vehicle Cooling System - "Motor Coolant")
  9. Drain the rear motor and reduction gear oil. (Refer to Rear Motor and Reduction Gear System - "Rear Motor and Reduction Gear Oil")
  10. Disconnect the coolant hoses (A) after releasing the quick connector.
  11. Remove the Integrated Drive Axle (IDA). (Refer to Driveshaft and Axle - "Integrated Drove Axle (IDA)")
  12. Remove the rear coil spring. (Refer to Rear Suspension System - "Rear Coil Spring")
  13. Remove the rear wheel speed sensor wiring bracket (A) after removing the bolt.

    Tightening torque : 19.6 - 29 N·m

  14. Disconnect the main connector (A).
  15. Remove the ground bolt (A).

    Tightening torque : 7.8 - 11,8 N·m

  16. Disconnect the high voltage cable connector (A).
    How to disconnect the connector
    1. Release the locking clip (A) by pulling it.
    2. Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).
  17. Remove the high voltage cable bracket nuts (A).

    Tightening torque : 9.8 - 11,8 N·m

  18. Remove the rear bumper under cover (A) after removing the mounting nuts and fasteners.

    Tightening torque : 7.8 - 11,8 N·m

  19. Remove the under cover bracket (A) after removing the mounting bolts.

    Tightening torque : 49.0 - 59 N·m

  20. Support the rear cross member with the table lift (A).
  21. Remove the rear cross member bolt and nut (A).

    Tightening torque : 176.5 - 196 N·m

  22. Lift up the vehicle slowly to remove the front motor and reduction gear assembly and rear cross member.
    • Before removing the motor and reducer assembly, make sure hoses and wire connectors are disconnected.
    • When removing the motor and reducer assembly, be careful not to damage any surrounding parts or body components.
  23. Disconnect the hose (A, B, C) after releasing the quick connector.
    (A) : Inverter inlet water hose (B) : Inverter outlet water hose (C) : Oil cooler outlet hose
  24. Disconnect the hose fixed clip.
    Widen the (A) of the hose clip, and then push the (B) in the direction of the arrow to unlock.
  25. Remove the inverter inlet water hose (A) and inverter outlet water hose (B).
  26. Remove the ground bolt (A).

    Tightening torque : 6.9 - 10,8 N·m

  27. Disconnect the main wiring protector (A) from the rear motor and reduction gear assembly after removing the mounting bolts.

    Tightening torque : 6.9 - 9,8 N·m

  28. Remove the high-voltage cable bracket by unscrewing bolts (A).

    Tightening torque : 7.8 - 11,8 N·m

  29. Remove the rear high voltage junction box. (Refer to Battery Control System - "Rear High Voltage Junction Box")
  30. Remove the multi inverter assembly. (Refer to Battery Control System - "Multi Inverter Assembly")
  31. Support the motor and reduction gear assembly using engine cranes and SST (09200 - 4X000).
    Install the SST (09200 - 4X000) to the rear motor and reduction gear assembly hangers.
  32. Remove the rear motor and reduction gear assembly mounting bolts (A, B, C).
    Tightening torque Bolts and nuts (A) : 107.9 - 128 N·m Bolts (B) : 63.7 - 83 N·m Bolt (C) : 176.5 - 196 N·m
  33. Remove the rear motor and reduction gear assembly from the rear cross member by lifting the engine crane upwards.

Rear Motor and Reduction Gear Assembly Installation

Installation

  1. Install in the reverse order of removal.
    Make sure the quick connector is installed securely after installing the coolant hose. [Type A] - Make sure the quick connector (A) is installed securely. [Type B] - Make sure the quick connector and quick connector clamp are installed securely. - Make sure that the quick connector protrusion (A) fits into the groove (B).
  2. Fill the coolant. (Refer to Electric Vehicle Cooling System - "Coolant")
    Using the KDS, perform Electric Water Pump (EWP) air bleeding.
  3. Refill the rear motor and reduction gear oil. (Refer to Rear Motor and Reduction Gear System - "Rear Motor and Reduction Gear Oil")
  4. After installing the rear motor and reduction gear assembly, perform the leakage test. (Refer to Battery Control System - "Air Tightness")
  5. Perform the "Motor Control Unit-Rear" and "Initialization of Automatic Resolver Offset Calibration" using the KDS. (Refer to Motor and Reduction Gear System - Motor Position & Temperature Sensor)
    If the resolver offset correction initialization is not performed, the output may be reduced and the drivable distance may be shortened.

Rear Motor and Reduction Gear Assembly Inspection

Inspection

[Phase Resistance]
  1. Remove the rear high voltage junction box. (Refer to Battery Control System - "Rear High Voltage Junction Box")
  2. Remove the multi inverter assembly. (Refer to Battery Control System - "Multi Inverter Assembly")
  3. Check the resistance of each line (U, V, W) using a multi-ohm meter.
    Item Inspection area Specifications Remark
    Phase resistance
    (Line - Line)
    U - V 57.48 - 63.52 mΩ Reference temperature : 20 - 20 °C
    V - W
    W - U
  4. Remove the rear high voltage junction box. (Refer to Battery Control System - "Rear High Voltage Junction Box")
  5. Remove the multi inverter assembly. (Refer to Battery Control System - "Multi Inverter Assembly")
  6. Check insulation resistance by using an insulation resistance tester.
    1. Connect the ( - ) terminal of the insulation resistance tester to the housing, and ( + ) terminal, to the 3-phase (U, V, W).
    2. Apply the DC 1,000 V voltage through insulation resistance tester and then wait about 1 minute to measure the stable resistance value.
    Item Inspection area Specifications Remark
    Insulation resistance Housing - U 100 MΩ or more DC 1,000 V, 1 minute
    Housing - V
    Housing - W
  7. Remove the rear high voltage junction box. (Refer to Battery Control System - "Rear High Voltage Junction Box")
  8. Remove the multi inverter assembly. (Refer to Battery Control System - "Multi Inverter Assembly")
  9. Check leakage current by using a withstanding voltage tester.
    1. Connect the ( - ) terminal of the withstand voltage tester to the housing and the ( + ) terminal to the 3-phase (U, V, W).
    2. Check the measured value by applying AC 2,200 V for one minute.
    Item Inspection area Specifications Remark
    Dielectric strength Housing - U 18 mA or less AC 2,200 V, 1minute
    Housing - V
    Housing - W
[Insulation Resistance] [Dielectric Strength]

Rear Motor and Reduction Gear Oil Replacement

Replacement

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on the high-voltage system or related system, make sure that you are familiar with and comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the instructions, serious accidents may occur due to electric shock or leakage.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
When checking the reduction gear oil level, be careful not to allow foreign substance (like dust) to enter through the filler hole.
  1. Remove the rear under cover. (Refer to Rear Motor and Reduction Gear System - "Rear Under Cover")
  2. Prepare a clean 5 ℓ beaker (A) to measure the amount of oil.
  3. Remove the drain plug (A) and drain oil, and then reinstall the drain plug.

    Tightening torque : 44.1 - 59 N·m

    The existing drain plug gasket (A) must be replaced with a new one (do not reuse).
  4. Remove the filler plug (A).
  5. Fill the specified oil through the filler plug hole as much as it has been drained.

    Recommended : Kia genuine ATF SP4M-1

  6. Install the filler plug (A).

    Tightening torque : 44.1 - 59 N·m

    The existing filler plug gasket (A) must be replaced with a new one (do not reuse).
  7. Install the rear under cover. (Refer to Rear Motor and Reduction Gear System - "Rear Under Cover")

Rear Motor and Reduction Gear Oil Seal Replacement

Special Service Tool

Tool Name / Number Illustration Description
Reduction gear oil seal installer
09445 - GI100
Installation of the oil seal on the rear reduction gear case side
(Used with the handle)
Reduction gear oil seal installer
09445 - GI200
Installation of the oil seal on the rear reduction gear housing side
(Used with the handle)
Handle
09231 - H1100
Used with the oil seal installer

Replacement

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on the high-voltage system or related system, make sure that you are familiar with and comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the instructions, serious accidents may occur due to electric shock or leakage.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Drain the rear motor and reduction gear oil. (Refer to Rear Motor and Reduction Gear System - "Rear Motor and Reduction Gear Oil")
  2. Remove the Integrated Drive Axle (IDA). (Refer to Driveshaft and Axle - "Integrated Drive Axle (IDA)")
  3. Remove the oil seal (A). Case side Housing side
  4. When installing a new oil seal, use the handle (09231 - H1100) and specified oil seal installer. Reduction gear case side : oil seal installer (09445 - GI100) Reduction gear housing side : oil seal installer (09445 - GI200)
  5. Install the Integrated Drive Axle (IDA). (Refer to Driveshaft and Axle - "Integrated Drive Axle (IDA)")
  6. Refill the rear motor and reduction gear oil. (Refer to Rear Motor and Reduction Gear System - "Rear Motor and Reduction Gear Oil")