Motor Position and Temperature Sensor Description and Operation. Motor Position and Temperature Sensor Components and Components Location
In this manual: Motor and Reduction Gear System
91steps
~546min
4/5difficulty
Tightening torque found on this page
Done 0 of 91
Contents:
Motor Position and Temperature Sensor Description and Operation. Motor Position and Temperature Sensor Components and Components Location
Motor Position and Temperature Sensor Description and Operation
Description
Motor position sensor Accurate motor rotor absolute position detection is required for motor control. The MCU can control the motor under optimal conditions using the position and speed of the rotor transmitted from the resolver. The resolver is mounted on a rear plate and consists of the rotor connected with motor rotor, and stator connected with housing. This locates the position of the rotor inside the motor, like the CMP sensor of the ICE vehicle. Motor temperature sensor The motor temperature sensor is assembled on the motor coil and is responsible for sensing motor temperature information for torque compensation and motor over-temperature protection according to temperature.
Motor Position and Temperature Sensor Components and Components Location
Components and Components Location
Front Motor 1. Motor Position and Temperature Sensor Connector 1-a. 9.8 - 11,8 N·m Rear Motor 1. Motor Position and Temperature Sensor Connector 1-a. 9.8 - 11,8 N·m
Motor Position and Temperature Sensor Removal and Installation - Front Motor
Removal
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
When working a high-voltage system, the technician must recognized and observe "General Safety Information and Caution". If not follow, serious accidents like electric shocks and short circuit may be caused.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Use a fender cover to protect the painted surface.
Be careful not to damage the connector when disconnecting.
Mark all wiring and hoses to prevent incorrect connections.
Shut off the high voltage circuit. (Refer to Motor and Reduction Gear System - "High Voltage Shut-off Procedures")
Remove the front trunk. (Refer to Body - "Front Trunk")
Disconnect the motor position and temperature sensor connector (A).
Slightly pull out the motor position and temperature sensor connector (A) after removing the mounting bolt.
Tightening torque : 9.8 - 11,8 N·m
Remove the motor position and temperature sensor connector (A) after disconnecting the connector.
Installation
Install in the reverse order of removal.
Motor Position and Temperature Sensor Removal and Installation - Rear Motor
Removal
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
When working a high-voltage system, the technician must recognize and observe "General Safety Information and Caution". If not, serious accidents like electric shocks and short circuits may be caused.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Use a fender cover to protect the painted surface.
Be careful not to damage the connector when disconnecting.
Mark all wiring and hoses to prevent incorrect connections.
Shut off the high voltage circuit. (Refer to Motor and Reduction Gear System - "High Voltage Shut-off Procedures")
Remove the rear motor and reduction gear assembly. (Refer to Motor and Reduction Gear System - "Rear Motor and Reduction Gear Assembly")
Disconnect the motor position and temperature sensor connector (A).
Slightly pull out the motor position and temperature sensor connector (A) after removing the mounting bolt.
Tightening torque : 9.8 - 11,8 N·m
Remove the motor position and temperature sensor connector (A) after disconnecting the connector.
Installation
Install in the reverse order of removal.
Motor Position and Temperature Sensor Inspection
Front Motor Position and Temperature Sensor Inspection
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
When working on the high-voltage system or related system, make sure that you are familiar with and comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the instructions, serious accidents may occur due to electric shock or leakage.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Shut off the high voltage circuit. (Refer to Motor and Reduction Gear System - "High Voltage Shut-off Procedures")
Remove the front trunk. (Refer to Body - "Front Trunk")
Remove the inverter assembly. (Refer to Battery Control System - "Inverter Assembly - 4WD")
Disconnect the motor position and temperature sensor connector (A).
Check the phase resistance using a multi tester.
Item
Inspection area
Specifications
Remark
Motor temperature sensor
Phase resistance
Pin 5 - Pin 10
18.1 - 20.8 kΩ
Reference temperature : 20 °C
Insulation resistance
Pin 5 - Motor housing
100 MΩ or more
Apply DC 500 V for 5 seconds
Pin 5 - Motor U/ V/ W
Dielectric strength
Pin 5 - Motor housing
0.5 mA or less
Apply AC 1,800v for 1 second
Motor position sensor
Phase resistance
Pin 2 - Pin 7
16.6 Ω ±7%
Reference temperature : 20 °C
Pin 3 - Pin 8
58.6 Ω ±7%
Pin 4 - Pin 9
49.8 Ω ±7%
Insulation resistance
Pin 2 - Motor housing
100 MΩ or more
Apply DC 500 V for 5 seconds
Pin 3 - Motor housing
Pin 4 - Motor housing
Initialization of Front Motor Resolver Offset Automatic Calibration
POWER "OFF" and connect the KDS to the Data Link Connector.
P range & POWER "ON" (Power button LED "Red"), Select "Vehicle S/W Management"
Perform the "Motor Control Unit-Front" and "Initialization of Automatic Resolver Offset Calibration" using the KDS.
Rear Motor Position and Temperature Sensor Inspection
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
When working a high-voltage system, the technician must recognize and observe "General Safety Information and Caution". If not, serious accidents like electric shocks and short circuits may be caused.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Shut off the high voltage circuit. (Refer to Motor and Reduction Gear System - "High Voltage Shut-off Procedures")
Remove the rear motor and reduction gear assembly. (Refer to Motor and Reduction Gear System - "Rear Motor and Reduction Gear Assembly")
Remove the multi inverter assembly. (Refer to Battery Control System - "Multi Inverter Assembly")
Disconnect the motor position and temperature sensor connector (A).
Check the phase resistance using a multi tester.
Item
Inspection area
Specifications
Remark
Motor temperature sensor
Phase resistance
Pin 5 - Pin 10
18.1 - 20.8 kΩ
Reference temperature : 20 °C
Insulation resistance
Pin 5 - Motor housing
100 MΩ or more
Apply DC 500 V for 5 seconds
Pin 5 - Motor U/ V/ W
Dielectric strength
Pin 5 - Motor housing
0.5 mA or less
Apply AC 1,800 V for 1 second
Motor position sensor
Phase resistance
Pin 2 - Pin 7
16.6 Ω ±7%
Reference temperature : 20 °C
Pin 3 - Pin 8
58.6 Ω ±7%
Pin 4 - Pin 9
49.8 Ω ±7%
Insulation resistance
Pin 2 - Motor housing
100 MΩ or more
Apply DC 500 V for 5 seconds
Pin 3 - Motor housing
Pin 4 - Motor housing
Initialization of Rear Motor Resolver Offset Automatic Calibration
POWER "OFF" and connect the KDS to the Data Link Connector.
P range & POWER "ON" (Power button LED "Red"), Select "Vehicle S/W Management"
Perform the "Motor Control Unit-Rear" and "Initialization of Automatic Resolver Offset Calibration" using the KDS.
SBW(Shift By Wire) Actuator Components and Components Location
SBW(Shift By Wire) Actuator Removal and Installation
Removal
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
When working on the high-voltage system or related system, make sure that you are familiar with and comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the instructions, serious accidents may occur due to electric shock or leakage.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Shut off the high voltage circuit. (Refer to Motor and Reduction Gear System - "High Voltage Shut-off Procedures")
Remove the rear motor and reduction gear assembly. (Refer to Motor and Reduction Gear System - "Rear Motor and Reduction Gear Assembly")
Separate the main wiring protector (A) after removing the bolts.
Tightening torque : 6.9 - 9,8 N·m
Disconnect the SBW (Shift By Wire) actuator connector (A).
Remove the SBW actuator (A) after removing the bolts.
Tightening torque : 20.6 - 28 N·m
Installation
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Install in reverse order of removal.
Install to the specified torque.
When installed, align the new output shaft (A) in the same position as the old output shaft (B) of the equipment.
Do not rotate the SBW actuator output shaft under excessive force when assembling, as this may cause damage to internal parts.limit value : -25° to +25°
Perform the order below with the KDS. (S/W Management → SCU - SBW Control Unit (SCU) → SCU Actuator Reducer Position Learning)
Refer to the KDS screen for operating conditions and details
Perform Over The Air (OTA) controller S/W update with KDS. (Refer to Body - "Over The Air (OTA)")
SBW(Shift By Wire) Lever Components and Components Location. SBW(Shift By Wire) Lever Removal and Installation
SBW(Shift By Wire) Lever Components and Components Location
When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.
Disconnect the battery negative ( - ) terminal and the service interlock connector. (Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD") (Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
Remove the floor console upper cover. (Refer to body - "Floor Console Upper Cover")
Disconnect the dial type SBW connector (A).
Remove the dial type SBW (A) after removing the screws.
Installation
Install in the reverse order of removal.
Oil Temperature Sensor Specification
Service Information
Item
Specification
Sensor Type
NTC thermistor
Operation Voltage (V)
4.75 - 5.25
Max current (mA)
100
Response time
Test medium : Coolant
MAX. 5 sec
Oil temperature [°C (°F)]
-40 to 150 (-40 to 302)
Oil Temperature Sensor Table
Temperature [°C (°F)]
Resistance (kΩ)
Minimum
Normal
Maximum
-40 (-40)
41.74
48.14
54.54
-30 (-22)
23.54
26.74
29.94
-20 (-4)
14.13
15.48
16.83
-10 (14)
8.393
9.308
10.223
0 (32)
5.281
5.790
6.299
10 (50)
3.422
3.714
4.007
20 (68)
2.310
2.450
2.590
30 (86)
1.554
1.658
1.762
40 (104)
1.084
1.148
1.212
50 (122)
0.7729
0.8126
0.8524
60 (140)
0.5615
0.5865
0.6115
70 (158)
0.4154
0.4311
0.4469
80 (176)
0.3122
0.3222
0.3322
90 (194)
0.2382
0.2446
0.2510
100 (212)
0.1844
0.1884
0.1924
110 (230)
0.1451
0.1471
0.1491
120 (248)
0.1139
0.1163
0.1187
130 (266)
0.0908
0.0930
0.0953
140 (284)
0.0731
0.0752
0.0773
150 (302)
0.0594
0.0614
0.0634
Oil Temperature Sensor Components and Components Location
Component
Front Motor
1. Oil Temperature Sensor 1-a. 9.8 - 11,8 N·m
2. O-ring
Rear Motor
1. Oil Temperature Sensor 1-a. 9.8 - 11,8 N·m
2. O-ring
Oil Temperature Sensor Removal and Installation - Front Motor
Removal
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
When working on the high-voltage system or related system, make sure that you are familiar with and comply with the "Safety Precautions, Caution, and Warnings." If you do not comply with the instructions, serious accidents may occur due to electric shock or leakage.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Disconnect the battery negative ( - ) terminal and the service interlock connector. (Refer to Battery Control System - "Auxiliary 12 V Battery")
Remove the front under cover. (Refer to Front Motor and Reduction Gear System - "Front Under Cover")
Drain the front motor and reduction gear oil. (Refer to Front Motor and Reduction Gear System - "Front Motor and Reduction Gear Oil")
Disconnect the oil temperature sensor connector (A).
Remove the oil temperature sensor (A) after removing the bolt.
Tightening torque : 9.8 - 11,8 N·m
Installation
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
When working on the high-voltage system or related system, make sure that you are familiar with and comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the instructions, serious accidents may occur due to electric shock or leakage.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Install in the reverse order of removal.
The existing oil temperature sensor O-ring (A) must be replaced with a new one (do not reuse).
Refill the front motor and reduction gear oil. (Refer to Front Motor and Reduction Gear System - "Front Motor and Reduction Gear Oil")
Oil Temperature Sensor Removal and Installation - Rear Motor
Removal
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
When working on the high-voltage system or related system, make sure that you are familiar with and comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the instructions, serious accidents may occur due to electric shock or leakage.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Disconnect the battery negative ( - ) terminal and the service interlock connector. (Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD") (Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
Remove the rear under cover. (Refer to Motor and Reduction Gear System - "Rear Under Cover")
Drain the rear motor and reduction gear oil. (Refer to Rear Motor and Reduction Gear System - "Rear Motor and Reduction Gear Oil")
Disconnect the oil temperature sensor connector (A).
Remove the oil temperature sensor (A) after removing the bolt.
Tightening torque : 9.8 - 11,8 N·m
Installation
When working on the high-voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
When working on the high-voltage system or related system, make sure that you are familiar with and comply with the "Safety Precautions, Caution, and Warnings." If you do not comply with the instructions, serious accidents may occur due to electric shock or leakage.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Install in the reverse order of removal.
The existing oil temperature sensor O-ring (A) must be replaced with a new one (do not reuse).
Refill the rear motor and reduction gear oil. (Refer to Rear Motor and Reduction Gear System - "Rear Motor and Reduction Gear Oil")
Electronic Oil Pump (EOP) Components and Components Location
Component
Front Motor
1. Electric Oil Pump (EOP) 1-a. 19.6 - 26 N·m
2. O-ring
Rear Motor
1. Electric Oil Pump (EOP) 1-a. 19.6 - 26 N·m
2. O-ring
Electronic Oil Pump (EOP) Removal and Installation - Front Motor
Removal
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
When working on the high-voltage system or related system, make sure that you are familiar with and comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the instructions, serious accidents may occur due to electric shock or leakage.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Use a fender cover to protect the painted surface.
Be careful not to damage the connector when disconnecting.
When disconnecting a quick connector, refer to the following according to the type of quick connector. - Remove while pressing the quick connector clamp (A) in the direction of the arrow. - Do not touch the rubber seal (B) inside the hose.
Disconnect the battery negative ( - ) terminal and the service interlock connector. (Refer to Battery Control System - "Auxiliary 12 V Battery")
Remove the front under cover. (Refer to Front Motor and Reduction Gear System - "Front Under Cover")
Drain the coolant. (Refer to Cooling System - "Coolant")
Drain the front motor and reduction gear oil. (Refer to Front Motor and Reduction Gear System - "Front Motor and Reduction Gear Oil")
Disconnect the Electronic Water Pump (EWP) quick connector hose (A).
Disconnect the Electronic Oil Pump (EOP) connector (A).
Remove the EOP (A) after removing the bolts.
Tightening torque : 19.6 - 26 N·m
Installation
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
When working on the high-voltage system or related system, make sure that you are familiar with and comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the instructions, serious accidents may occur due to electric shock or leakage.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Install in the reverse order of removal.
The existing O-ring (A) must be replaced with a new one (do not reuse).
When reinstalling EOP, replace the O-ring (A) with a new one (do not reuse).
Make sure the quick connector is installed securely.
Refill the front motor and reduction gear oil. (Refer to Front Motor and Reduction Gear System - "Front Motor and Reduction Gear Oil")
Fill the coolant. (Refer to Cooling System - "Coolant")
Electronic Oil Pump (EOP) Removal and Installation - Rear Motor
Removal
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
When working on the high-voltage system or related system, make sure that you are familiar with and comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the instructions, serious accidents may occur due to electric shock or leakage.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Disconnect the battery negative ( - ) terminal and the service interlock connector. (Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD") (Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
Remove the rear under cover. (Refer to Rear Motor and Reduction Gear System - "Rear Under Cover")
Drain the rear motor and reduction gear oil. (Refer to Rear Motor and Reduction Gear System - "Rear Motor and Reduction Gear Oil")
Disconnect the Electronic Oil Pump (EOP) connector (A).
Remove the EOP (A) after removing the bolts.
Tightening torque : 19.6 - 26 N·m
Installation
When working on the high-voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
When working on the high-voltage system or related system, make sure that you are familiar with and comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the instructions, serious accidents may occur due to electric shock or leakage.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Install in the reverse order of removal.
The existing O-ring (A) must be replaced with a new one (do not reuse).
When reinstalling EOP, replace the O-ring (A) with a new one (do not reuse).
Refill the rear motor and reduction gear oil. (Refer to Rear Motor and Reduction Gear System - "Rear Motor and Reduction Gear Oil")
Disconnect Actuator System (DAS) Motor Components and Components Location. Disconnect Actuator System (DAS) Motor Description and Operation
Disconnect Actuator System (DAS) Motor Components and Components Location
Disconnect Actuator System (DAS) Motor Description and Operation
Description
The 4WD system improves driving performance but also reduce driving range. To compensate for shortening range, 2WD drive (rear-wheel motor and reduction gear) is applied depending on driving conditions and *DAS is applied to cut off the drive line to reduce front-wheel motor and reduction gear line resistance. The actuator (DAS motor) installed for controlling the DAS, The DAS motor takes the VCU signal and connects or disconnects the deceleration gear and the driveshaft. *DAS : Disconnect Actuator System *VCU : Vehicle Control Unit DAS Component DAS Motor Operating Conditions by Driving Condition
Item
2WD → 4WD
4WD → 2WD
Drive mode
SNOW, SPORT MODE
※ If the conditions on the left are not met and the conditions below are met
ECO MODE [However, if the vehicle speed is less than 15 km/h, it will be connected]
When ABS is operates
Rapid steering
Steering angle more than 60° , and angular acceleration 40°/sec
Driving at gradient
Gradient more than 8%
Vehicle speed [kph (mph)]
15 (9.3) or slower, 120 (74.5) or faster (Normal mode only)
The driver's will for acceleration.
When the torque required by the driver is greater than the maximum torque of the rear wheels.
Electronic brake actuation.
When TCS, ESC operate.
Disconnect Actuator System (DAS) Motor Removal and Installation
Removal
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
When working on the high-voltage system or related system, make sure that you are familiar with and comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the instructions, serious accidents may occur due to electric shock or leakage.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Disconnect the battery negative ( - ) terminal and the service interlock connector. (Refer to Battery Control System - "Auxiliary 12 V Battery")
Remove the front under cover. (Refer to Front Motor and Reduction Gear System - "Front Under Cover")
Disconnect the Disconnect Actuator System (DAS) motor connector (A).
Remove the DAS motor (A) after removing the hexagon socket head bolts. Tightening torque : 4.9 - 5,9 N·m (0.5 - 0.6 kgf·m, 3.6 - 4.3 lb·ft, 43.4 - 52.1 lb·in)
Installation
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
When working on the high-voltage system or related system, make sure that you are familiar with and comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the instructions, serious accidents may occur due to electric shock or leakage.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Install in the reverse order of removal.
The existing O-ring (A) must be replaced with a new one (do not reuse).
Vehicle Control Unit (VCU) Description and Operation
Description
Vehicle Control Unit (VCU) is the top-level controller of the vehicle that combines all the information to meet the driver's needs.
VCU comprehensively controls Drive motor control, Air conditioning load control, 12 V electric load power supply control, Disconnect Actuator System (DAS), and others.
Function
Detail
Drive Motor Control
Calculate usable battery power
Calculate usable motor toque
Order motor torque considering Driver demands (APS, Brake SW, Shift lever)
A/C Load Control
Order the final FATC permission power by using the battery information and FATC request power data.
12 V Electric Load Power Supply Control
LDC operation mode is determined according to 12 V battery information and vehicle status.
Disconnect Actuator System (DAS) Motor
As DAS is applied to 4WD vehicles, it controls the connection or disconnection between the front wheel motor and drive shafts depending on the driving condition.
Cluster control
Command to indicate Drive Power, Energy Flow, Service lamp & various lamp lighting.
Distance to Empty (DTE)
Command to indicates usable battery energy and distance to empty based on prior drive pattern.
If drive path is set by using AVNT, DTE accuracy is improved by estimating the energy consumption to destination.
Booking / Remote control
Remote control through a smartphone linked with Kia connect
Reservation Function through operation time setting by driver.
Regenerative braking control
Calculate motor charge torque command for regenerative braking.
Calculate regenerative brake force.
Vehicle Control Unit (VCU) Components and Components Location
4. Auxiliary 12 V Battery 5. Vehicle Control Unit (VCU) 5-a. 9.8 - 11,8 N·m 6. Battery Tray 6-a. 9.8 - 13,7 N·m
Vehicle Control Unit (VCU) Removal and Installation - 2WD
Removal
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
When working a high-voltage system, the technician must recognize and observe "General Safety Information and Caution". If not, serious accidents like electric shocks and short circuits may be caused.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Remove the auxiliary 12 V battery. (Refer to Battery Control System - "Auxiliary 12 V Battery")
Disconnect the Vehicle Control Unit (VCU) connector (A).
Remove the VCU assembly (A) after removing the bolts.
Tightening torque : 9.8 - 11,8 N·m
Separate the bracket from the VCU (A) by removing the bolts.
Tightening torque : 9.8 - 11,8 N·m
Installation
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
When working a high-voltage system, the technician must recognize and observe "General Safety Information and Caution". If not, serious accidents like electric shocks and short circuits may be caused.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Install in the reverse order of removal.
Install the Vehicle Control Unit (VCU) to the specified torque values.
If the VCU drops, it may cause internal damage. Replace it with a new one. (Don't reuse)
Perform the Write VIN procedures with the KDS. (S/W Management → Vehicle Control Unit → Write VIN)
Vehicle Control Unit (VCU) Removal and Installation - 4WD
Removal
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
When working a high-voltage system, the technician must recognize and observe "General Safety Information and Caution". If not, serious accidents like electric shocks and short circuits may be caused.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Remove the auxiliary 12 V battery. (Refer to Battery Control System - "Auxiliary 12 V Battery")
Disconnect the Vehicle Control Unit (VCU) connector (A).
Separate the wiring (A) fastened to the VCU bracket.
Remove the VCU assembly (A) after removing the bolts.
Tightening torque : 9.8 - 11,8 N·m
Separate the bracket from the VCU (A) by removing the bolts.
Tightening torque : 9.8 - 11,8 N·m
Installation
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
When working a high-voltage system, the technician must recognize and observe "General Safety Information and Caution". If not, serious accidents like electric shocks and short circuits may be caused.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Install in the reverse order of removal.
Install the Vehicle Control Unit (VCU) to comply with the specified torque values.
If the VCU drops, it may cause internal damage. Replace it with a new one. (Don't reuse)
Perform the Write VIN procedures with the KDS. (S/W Management → Vehicle Control Unit → Write VIN)
Accelerator Pedal Module Specification
Specification
Accelerator Pedal Position
Output Voltage (V)
APS 1
APS 2
Idle Stroke
0.7 - 0.8
0.33 - 0.43
Full Stroke
3.98 - 4.22
1.93 - 2.17
Accelerator Pedal Module On Vehicle Inspection
On Vehicle Inspection
Diagnostic equipment (KDS) can be used to diagnose faulty parts quickly. (Refer to "DTC Diagnostic Guide")
Self diagnosis : Inspection and display failed code (DTC)
Sensor data : Checking the system input/output values
Forced operation : Checking the system operation condition
Additional function : Controlling other features including system option setting and zero point adjustment
Component Inspection
Checks the output voltage of the sensor 1 and sensor 2 according to accelerator pedal state by using a KDS.
Accelerator Pedal Position
Output Voltage (V)
APS 1
APS 2
Idle Stroke
0.7 - 0.8
0.33 - 0.43
Full Stroke
3.98 - 4.22
1.93 - 2.17
Accelerator Pedal Module Removal and Installation
Removal
Disconnect the battery negative ( - ) terminal and the service interlock connector. (Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD") (Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
Disconnect the connector (A).
Remove the accelerator pedal module (A) after removing the nuts.
Tightening torque : 12.7 - 15,7 N·m
Installation
Install in the reverse order of removal.
Install the accelerator pedal module to comply with the specified torque values.
If the accelerator pedal module drops, it may cause internal damage. Replace it with a new one. (Don't resue)