Brake System

Integrated Electronic Brake (IEB) System

23steps
~138min
4/5difficulty
0102030405010.88N·mlb·ft
Tightening torque found on this page
Done 0 of 23

Contents:

Description and Operation. Reservoir Tank Components and Components Location

Description and Operation

Description

Regeneration Brake System Regenerative braking system refers to a system that charges batteries by converting kinetic energy generated during vehicle deceleration and braking into electrical energy. The amount of regenerative braking is determined by the speed of the vehicle, the amount of charge of the battery, etc. It is possible to improve energy efficiency when driving in urban areas where acceleration and deceleration are repeated. Operation of the regeneration brake system The distribution of braking forces is allocated by controlling hydraulic braking, and the overall braking force (hydraulic + regeneration) is become the braking force required by the driver. If regenerative braking is not performed due to failure, etc., the overall braking force required by the driver is supplied by the hydraulic braking system. Brake mode The driver can change the brake mode to 'Normal' or 'Sports' mode on the AVNT. Depending on the mode selected, hydraulic pressure is adjusted in the Integrated Electric Brake (IEB) to provide braking performance. Normal mode : Normal braking mode provides balanced braking performance. Sport mode : It provides a stronger braking force by providing higher hydraulic pressure to the same pedal stroke compared to the normal mode.

Operation

General Braking ABS Back up Braking (IEB Fail)

Reservoir Tank Components and Components Location

Components and Components Location

Do not disassemble the Integrated Electronic Brake (IEB).
1. Reservoir Cap
2. Remote Reservoir Tank Hose
3. Remote Reservoir Tank
3-a. 6.9 - 10,8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft, 60.8 - 95.5 lb·in)

4. Reservoir Tank
4-a. 1.0 - 1,5 N·m (0.10 - 0.15 kgf·m, 0.7 - 1.1 lb·ft, 8.7 - 13.0 lb·in)
5. Integrated Electronic Brake (IEB)

Reservoir Tank Removal and Installation

Removal

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Disconnect the battery negative ( - ) terminal and the service interlock connector. (Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD") (Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
  2. Remove the front trunk. (Refer to Body - "Front Trunk")
  3. Disconnect the brake fluid level sensor (A).
  4. Remove the brake fluid from the reservoir tank by using a suitable tool after opening the reservoir cap (A).
    Be careful not to spill brake fluid onto the vehicle or body. If brake fluid leaks, wash off with water and remove with a clean cloth as soon as possible.
    When opening the tank cap, make sure there is no dust or other foreign substances to contaminate the brake fluid.
  5. Separate the remote reservoir tank hose (A) after releasing the clamp.
  6. Remove the reservoir tank assembly (A) after removing the nuts.
    Tightening torque : 6.9 - 10,8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft, 60.8 - 95.5 lb·in)
  7. Remove the reservoir tank (A) after removing the screws.
    Tightening torque : 1.0 - 1,5 N·m (0.10 - 0.15 kgf·m, 0.7 - 1.1 lb·ft, 8.7 - 13.0 lb·in)
  8. Remove the grommets (A).
    Do not reuse the grommets (A).

Installation

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Install in the reverse order of removal.
    Check the brake fluid level sensor is securely connected during installation, poor connection may cause the brake warning lamp to illuminate.
  2. Fully fill the reservoir tank with brake fluid and perform the air bleed procedure. (Refer to Brake System - "Brake Bleeding")
  3. Check the brake fluid leakage and pedal operating condition.

Integrated Electronic Brake (IEB) Components and Components Location

Components and Components Location

Do not disassemble the Integrated Electronic Brake (IEB).
1. Reservoir Cap
2. Reservoir Hose
3. Remote Reservoir Tank
3-a. 6.9 - 10,8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft, 60.8 - 95.5 lb·in)

4. Reservoir Tank
4-a. 1.0 - 1,5 N·m (0.10 - 0.15 kgf·m, 0.7 - 1.1 lb·ft, 8.7 - 13.0 lb·in)
5. Integrated Electronic Brake (IEB)

Integrated Electronic Brake (IEB) Removal and Installation

Removal

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
When replacing the Integrated Electronic Brake (IEB), enter the variant coding value of the existing IEB into the new IEB using one of the methods below.
  • Select 'Variant coding (Backup and Write)' on the S/W management menu and follow the on-screen instructions.
  • Select the 'System Identification' on the S/W management menu and record the existing variant coding value, and after replacing the IEB, select the 'ESC Variant coding' on the menu and enter the recorded value.
  1. Disconnect the battery negative ( - ) terminal and the service interlock connector. (Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD") (Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
  2. Remove the Vehicle Control Unit (VCU). (Refer to Motor and Reduction Gear System - "Removal and Installation - 2WD") (Refer to Motor and Reduction Gear System - "Removal and Installation - 4WD")
  3. Remove the reservoir tank. (Refer to Integrated Electronic Brake (IEB) System - "Reservoir Tank")
  4. Disconnect the main connector (A).
  5. Separate the brake lines (A) after loosening the flare nuts.

    Tightening torque : 12.7 - 16,7 N·m

    • If the extension wrench (A) is used to tighten the flare nut, refer to the below formula and calculate the true torque.
    • True torque = Torque wrench dial reading
    • True torque = [Torque wrench / (A + B)] × Torque wrench dial reading
  6. Remove the brake pedal arm mounting clevis pin (A) after removing the split pin (B).
    Do not reuse the split pin (B).
  7. Remove the Integrated Electronic Brake (IEB) assembly nuts (A).

    Tightening torque : 16.7 - 26 N·m

  8. Remove the IEB (A).
    Be careful not to interfere with other parts when installing or removing IEB (A).

Installation

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Install in the reverse order of removal.
    • Check the brake fluid level sensor is securely connected during installation, poor connection may cause the brake warning lamp to illuminate.
    • Apply the grease when installing the brake pedal arm clevis pin (Grease type : GREASE PDLV-1)
    • Be careful not to change the mounting position of the clevis pin and split pin.
    • When transporting IEB, hold only (A) not the piston guard, operating rod, reservoir. And be careful not to damage the IEB.
    To minimize damage to the thread and brake member assembly during installation, tighten all nuts with hands and then tighten them to the tightening torque values in the order shown below.
  2. Fill the brake reservoir with brake fluid and perform the brake bleeding procedure. (Refer to Brake System - "Brake Bleeding")
  3. Perform the order below with the KDS. (S/W Management → ABSESP - Braking Control → ESC Variant Coding) (S/W Management → ABSESP - Braking Control → Pressure Sensor Calibration) (S/W Management → ABSESP - Braking Control → Longitudinal Gsensor Calibration (HAC/DBC Only) (S/W Management → ABSESP - Braking Control → Brake Pedal Travel Sensor (PTS) Calibration)
    Refer to the KDS screen for operating conditions and details
  4. Perform Over The Air (OTA) controller S/W update with KDS. (Refer to Body - "Over The Air (OTA)")