Brake System

ESC (Electronic Stability Control) System

67steps
~402min
4/5difficulty
0102030405029.422N·mlb·ft
Tightening torque found on this page
Done 0 of 67

Contents:

Components and Components Location

Components and Components Location

[2WD]

1. Integrated Electronic Brake (IEB)
2. Front Wheel Speed Sensor
3. Rear Wheel Speed Sensor

[4WD]

1. Integrated Electronic Brake (IEB)
2. Front Wheel Speed Sensor
3. Rear Wheel Speed Sensor

Description and Operation

Description

Electronic Stability Control (ESC) recognizes critical driving conditions, such as panic reactions in dangerous situations, and stabilizes the vehicle by individual wheel braking and engine control input. ESC adds an additional function known as Active Yaw Control (AYC) to the ABS, TCS, EBD and ESC functions. On contrary, the ABS/TCS function controls wheel slip during braking and accelerating, and thus, mainly intervenes in the longitudinal dynamics of the vehicle, and the active yaw control stabilizes the vehicle on the vertical axis. This is achieved by individual wheel brake intervention and adaptation of momentary engine torque with no need for any action to be taken by the driver. ESC essentially consists of three assemblies : the sensors, the electronic control unit and the actuators. The stability control feature works under all driving and operating conditions. Under certain driving conditions, the ABS/TCS function can be activated simultaneously with the ESC function in response to a command by the driver. In the event of a failure of the stability control function, the basic safety function, ABS, is still maintained. Description of ESC Control ESC system consists of ABS/EBD, TCS and AYC functions. ABS/EBD function : The IEB changes the active sensor signal (current shift) coming from the four wheel sensors into square waves. By using the input of above signals, the IEB calculates the vehicle speed and the acceleration & deceleration of the four wheels. And, the IEB determines whether the ABS/EBD should be actuated or not. TCS function prevents the wheel slip of drive direction by adding the brake pressure and engine torque reduction via CAN communication. TCS function uses the wheel speed sensor signal to determine the wheel slip as far as ABS function. AYC function prevents unstable maneuver of the vehicle. To determine the vehicle maneuver, AYC function uses the maneuver sensor signals (Yaw Rate Sensor, Lateral Acceleration Sensor, and Steering Wheel Angle Sensor). If vehicle maneuver is unstable (Over Steer or Under Steer), AYC function applies the brake pressure on certain wheel, and sends engine torque reduction signal by CAN. After the ignition on, the IEB continuously diagnoses the system for failures (self-diagnosis). If a system failure is detected, the IEB informs driver of the system failure through the BRAKE/ABS/ESC warning lamp (fail-safe warning). Input and Output Diagram

ESC Operation Mode

Warning Lamps
Lamp Name
ABS Warning Lamp
EBD / Parking Brake Warning Lamp
ESC Operating / Warning Lamp
ESC OFF Lamp
EPB Warning Lamp

ABS Warning Lamp Module The active ABS warning lamp module indicates the self-test and failure status of the ABS. The ABS warning lamp is turned on under the following conditions:
  • During the initialization phase after IGN ON. (continuously for 3 seconds).
  • In the event of ABS function failure.
  • During diagnostic mode.
  • When the communication between IEB and PCM has failed.
  • Cluster lamp is ON when communication is impossible with CAN module.
EBD / Parking Brake Warning Lamp Module The active EBD warning lamp module indicates the self-test and failure status of the EBD. However, in case the Parking Brake Switch is turned on, the EBD warning lamp is always turned on regardless of EBD functions. The EBD warning lamp is turned on under the following conditions:
  • During the initialization phase after IGN ON. (continuously for 3 seconds).
  • When the Parking Brake Switch is ON or brake fluid level is low.
  • When the EBD function has a failure.
  • During diagnostic mode.
  • When the communication between IEB and PCM has failed.
  • Cluster lamp is ON when communication is impossible with CAN module.
ESC Operating / Warning Lamp The ESC function/warning lamp indicates the self-test and failure status of the ESC. The ESC function/warning lamp is turned on under the following conditions:
  • During the initialization phase after IGN ON. (continuously for 3 seconds).
  • When the ESC function is inhibited by system failure.
  • When the ESC control is operating. (Blinking - 2Hz)
  • During diagnostic mode (except standard mode).
  • Cluster lamp is ON when communication is impossible with CAN module.
ESC Off Lamp The ESC Off lamp indicates the self-test and operating status of the ESC. The ESC Off lamp operates under the following conditions :
  • During the initialization mode after IGN ON. (continuously for 3 seconds).
  • ESC Off lamp is ON when driver turns OFF ESC switch.
ESC On / Off Switch The ESC On/Off Switch is used to toggle the ESC function between On/Off states based upon driver input. The On/Off switch is a normally open, is a momentary contact switch. Initial status of the ESC function is ON.

Troubleshooting

Troubleshooting

Failure Diagnosis
  1. In principle, ESC and TCS controls are prohibited in case of ABS failure.
  2. When ESC or TCS fails, only the failed system control is prohibited.
  3. The solenoid valve relay should be turned off in case of ESC failure, refer to the ABS fail-safe.
  4. Information on ABS fail-safe is identical to the fail-safe in systems where ESC is not installed.
  5. It keeps the code as far as the backup lamp power is connected.
  6. It stores the code as long as IEB is powered ON.
  7. Initial test is performed immediately after the IEB is powered on.
  8. Valve relay test is performed immediately after switching "ON" the IG2.
  9. Test are performed at all times the ignition (IG2) is ON.
  10. Initial test is performed in the following cases.
    1. When the failure is not detected momentarily
    2. When ABS and ESC are not in control.
    3. If initial test is not made after supplying power to ECU.
    4. If the vehicle speed is over 8 km/h with the brake lamp switched off.
    5. When the vehicle speed is over 40 km/h.
  11. Test continues even if the brake lamp is switched on.
  12. When performing ABS or ESC control before the initial test, stop the initial test and wait for the IEB power input again.
  13. Determining failure in the following cases.
    1. When the power is normal.
    2. From the point in which the vehicle speed reaches 8 km/h after IEB power on.
  14. Turn the system down and perform the following actions and wait for IEB to power OFF.
  15. Turn the valve relay off.
  16. Stop the control during the operation and do not execute anything until it recovers to normal condition.
  17. ESC warning lamps turns on for 3 seconds after IGN ON.
  18. ESC function lamp blinks when ESC Activated.
  19. In case of ESC failure, ESC warning lamp turns ON.
  20. ESC OFF lamp turns on: – When ESC is switched OFF –3 seconds after IGN ON
Failure Code Memory Failure Test Failure Countermeasures Warning Lamp ON Standard Flow of Diagnostic Troubleshooting Notes With Regard To Diagnosis The conditions listed in the following table are not abnormal.
Condition Explanation
System check sound When starting the engine, a thudding sound can sometimes be heard coming
from inside the engine compartment. This is because the system operation
check is being performed.
ESC operation sound
  1. Sound of the motor inside the IEB operation (whine).
  2. Sound is generated along with vibration of the brake pedal (scraping).
  3. When ESC operates, sound is generated from the vehicle chassis due to repeated brake application and release (Thump : suspension; squeak: tires)
ESC operation
(Long braking distance)
On snow-covered or gravel roads, the braking distance for vehicles with ABS can sometime be longer than that of vehicles without ESC. Accordingly, advise customers to drive safely on such roads by reducing the vehicle speed.
Diagnostic detection conditions can vary depending on the diagnostic code.
When checking the trouble symptom after the diagnostic code has been erased, ensure that the requirements listed in "Comment" are met.

Checklist for diagnosis of ESC system Before and after the ESC system test, Do these steps to check the integrity of the warning lamp and ESC system.
  1. Inspection method Turn on the IGN and check ABS system: If ABS/BRAKE warning lamp illuminate for 3 seconds, warning lamp and ABS system are in normal condition.
    1. When the warning lamp does not illuminate when the IGN is turned on.
      1. Remove the ABS ECU connector in the engine room.
      2. Turn on the IGN.
      3. When the ABS / BRAKE warning light does not light up: This is a warning light related problem, so check the instrument panel and wiring.
      4. When the ABS / BRAKE warning light remains on: The warning light is normal and determines to be an ESC system error. Check the ESC system using KDS.
    2. If the warning lamp illuminates and does not turn off.
      1. Do the self test using KDS.
      2. Record the fault code after self test.
      3. Work with the recorded fault code and self test using KDS.
      4. If there are no faults after self test: test the IGN to verify normal condition.
      5. If there are faults after self test: do the inspection using the fault code check list.
  2. If there are faults after self-test using KDS even if ESC system and warning lamp are in normal condition, record the fault code and diagnose it.
    1. Make sure the IGN is switched off when removing or installing connectors.
    2. If a warning lamp illuminates or any abnormalities occurs during a driving test, perform and document vehicle inspection.
Problem Symptoms Table
Symptom Suspect Area
ESC does not operate. Only when 1 - 4 are all normal and the problem is still occurring, replace the IEB.
  1. Check the DTC reconfirming that the normal code is output.
  2. Power source circuit.
  3. Speed sensor circuit.
  4. Check the hydraulic circuit for leakage.
ESC does not operate intermittently. Only when 1 - 4 are all normal and the problem is still occurring, replace the ESC actuator assembly.
  1. Check the DTC reconfirming that the normal code is output.
  2. Wheel speed sensor circuit.
  3. Stop lamp switch circuit.
  4. Check the hydraulic circuit for leakage.
Communication with KDS
is not possible.
(Communication with any system is
not possible)
  1. Power source circuit
  2. CAN line
Communication with KDS
is not possible.
(Communication with ESC only is
not possible)
  1. Power source circuit
  2. CAN line
  3. IEB
When ignition is turned ON
(engine OFF),
the ESC warning lamp does not light up.
  1. ESC warning lamp circuit
  2. IEB
Even after the engine is started, the ESC
warning lamp remains ON.
  1. ESC warning lamp circuit
  2. IEB

During ESC operation, the brake pedal may vibrate or may not be able to be depressed. Such conditions are due to intermittent changes in hydraulic pressure inside the brake line to prevent the wheels from locking and is not an abnormality.

ESC OFF Switch Components and Components Location. ESC OFF Switch Description and Operation

ESC OFF Switch Components and Components Location

Components and Components Location

1. ESC OFF Switch


ESC OFF Switch Description and Operation

Description

The ESC OFF switch is operated when the driver arbitrarily prohibits ESC control. Pressing the ESC OFF switch will illuminate the ESC OFF lamp.

ESC OFF Switch Removal and Installation. Front Wheel Speed Sensor Components and Components Location

ESC OFF Switch Removal and Installation

Removal

  1. Remove the crash pad side switch. (Refer to Body - "Crash Pad Switch")

Installation

  1. Install in the reverse order of removal.

Front Wheel Speed Sensor Components and Components Location

Components and Components Location

[2WD]

1. Front Wheel Speed Sensor
2. Front Wheel Speed Sensor Harness
2-a. 19.6 - 29 N·m
3. Front Wheel Speed Sensor Connector

[4WD]

1. Front Wheel Speed Sensor
1-a. 8.8 - 13,7 N·m

2. Front Wheel Speed Sensor Harness
2-a. 19.6 - 29 N·m
3. Front Wheel Speed Sensor Connector

Front Wheel Speed Sensor Removal and Installation

Removal

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Disconnect the battery negative ( - ) terminal and the service interlock connector. (Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD") (Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
  2. Remove the front wheel and tires. (Refer to Suspension System - "Wheel")
  3. Separate the front dust cover (A) after removing the fastener.
  4. Disconnect the front wheel speed sensor connector (A).
  5. Remove the front wheel speed sensor bracket (A) after removing the bolt.

    Tightening torque : 19.6 - 29 N·m

  6. Separate the front wheel speed sensor harness (A) from the brake hose bracket.
  7. Remove the front wheel speed sensor.
    1. Disconnect the front wheel speed sensor connector (A). [2WD]
    2. Remove the front wheel speed sensor (A) after removing the bolt.. [4WD]

      Tightening torque : 8.8 - 13,7 N·m

Installation

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Install in the reverse order of removal.

Front Wheel Speed Sensor Replacement - 2WD

Special Service Tool

Tool Name / Number Illustration Description
Sensor Cap Installer
09527 - AL500
Used for installing of wheel sensor cap (O.D : Φ86.6)
(Used with 09231 - 93100)
Sensor Cap Remover
0K583 - R0400
Used for removal of wheel sensor cap
Handle
09231 - 93100
Handle
(Used with 09527 - AL500)

Replacement

Front wheel speed sensor cap (2WD)
  1. Remove the front hub assembly. (Refer to Driveshaft and Axle - "Front Hub Assembly")
  2. Check the installation direction of the sensor cap (A) connector (B).
    If the mounting direction of the sensor cap is different from the initial installation, the connector may not be able to be connected at the time of installation, so be sure to record the direction of the connection before removal.
  3. Remove the wheel sensor cap by using the SST.
    1. Install the SST (0K583 - R0400) on the wheel sensor cap and then rotate the bolts (A) to fix.
      Ensure that the bolts (A) and hub bearing mounting surfaces (B) are in contact when installing the SST.
    2. Remove the wheel sensor cap (B) by rotating upper bolts (A) of the SST (0K583 - R0400).
  4. Check the encoder (A) for deformation or damage.
    • After removing the sensor cap, check for damage to the encoder, and replace the hub bearing if the deformation is confirmed.
    • If the encoder is deformed, the warning lamp may illuminates due to a sensor error.
  5. Pre-install the sensor cap in the same direction as the connector direction of the sensor cap that was visually checked before disconnecting.
    Wipe off foreign substances and other contaminants inside the hub assembly before installing the sensor cap.
  6. Install the SST (09527 - AL500) to the pre-installed wheel sensor cap.
    Be careful not to interfere with connector (A) when installing special tools.
  7. Install the sensor cap by hammering the top of the SST after installing the SST (09231 - 93100).
    • Tilting the sensor cap during installation may damage the encoder.
    • Make sure that there is no gap (A) between the sensor cap and front hub assembly.
  8. Install the front hub assembly. (Refer to Driveshaft and Axle - "Front Hub Assembly")

Front Wheel Speed Sensor Inspection. Rear Wheel Speed Sensor Components and Components Location

Front Wheel Speed Sensor Inspection

On Vehicle Inspection

  1. The brake system can quickly diagnosed for problems by using the KDS (Refer to "DTC guide").
    1. Trouble code diagnosis : Inspection and display trouble code (DTC) (Refer to DTC guide when fault code is found.)
    2. S/W Management : Controlling other features including system option setting and zero point adjustment.
      Refer to the KDS screen for operating conditions and details

Rear Wheel Speed Sensor Components and Components Location

Components and Components Location

1. Rear Wheel Speed Sensor Connector
1-a. 8.8 - 13,7 N·m
2. Rear Wheel Speed Sensor Harness
2-a. 19.6 - 29 N·m
3. Rear Wheel Speed Sensor Connector
4. EPB Actuator Connector

Rear Wheel Speed Sensor Removal and Installation

Removal

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Disconnect the battery negative ( - ) terminal and the service interlock connector. (Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD") (Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
  2. Remove the rear wheel and tires. (Refer to Suspension System - "Wheel")
  3. Disconnect the Electronic Parking Brake (EPB) actuator connector (A).
  4. Remove the rear wheel speed sensor (A) after removing the bolt.

    Tightening torque : 8.8 - 13,7 N·m

  5. Separate the rear wheel speed sensor (A) from the rear upper arm after removing the bolt.

    Tightening torque : 19.6 - 29 N·m

  6. Remove the rear wheel speed sensor bracket (A) after removing the bolt.

    Tightening torque : 19.6 - 29 N·m

  7. Separate the rear wheel guard (A) after removing the fastener.
  8. Remove the rear wheel speed sensor after disconnecting the connector (A).

Installation

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Install in the reverse order of removal.

Rear Wheel Speed Sensor Inspection

On Vehicle Inspection

  1. The brake system can quickly diagnosed for problems by using the KDS (Refer to "DTC guide").
    1. Trouble code diagnosis : Inspection and display trouble code (DTC) (Refer to DTC guide when fault code is found.)
    2. S/W Management : Controlling other features including system option setting and zero point adjustment.
      Refer to the KDS screen for operating conditions and details

Emergency Stop Signal (ESS) System Description and Operation

Description

Emergency Stop Signal (ESS) Introduction
  • In case of sudden/quick braking from the driver, the brake/emergency lamp blinks to warn rear vehicles.
  1. Basic function (Blinking of the brake lamp/emergency lamp)
    • Operating condition : In case of quick braking or operation of ABS above a certain speed.
    • Releasing condition : In case not braking quick or use of the ABS operation.
  2. Additional function (Turn signal blinking)
    • Operation condition: ESS releasing after basic functioning.
    • – Releasing condition: Releasing at the start of driving.
System Component ESS Circuit diagram