Steering System

Description and Operation

46steps
~276min
4/5difficulty
02040608010058.843N·mlb·ft
Tightening torque found on this page
Done 0 of 46

Contents:

Description and Operation

Description and Operation

  • Automobiles are equipped with MDPS (Motor Driven Power Steering) assisted by electric drive motor to reduce the driver’s steering and ensure safety during steering.
    Classification by MDPS installing location
    • For C-MDPS (Column Type Motor Driven Power Steering), the electric motor is installed on the steering column axle.
    • For R-MDPS (Rack Type Motor Driven Power Steering), the electric motor is installed on the steering gear rack bar.
  • R-MDPS (Rack Type Motor Driven Power Steering) is installed on the steering gear rack bar and integrated with the motor and controller.
  • It increases the gear ratio compared to C-MDPS (based on the same gear) and improves the responsiveness when the driver operates the steering wheel. (This generally does, but may vary depending on the motor.)
  • The controller in R – MDPS receives various signals for control.
  • When the steering wheel is controlled, the R - MDPS receives the torque value from the torque sensor and controls the motor’s rotation.
  • It receives the signals from the vehicle’s speed sensor to control the steering wheel operating force.
  • It receives the rotation angle of the steering wheel from the angle sensor.
Control method depending on the driving conditions
  • When the driver controls the steering wheel during low-speed driving, R – MDPS offers light and comfortable steering feel.
  • When the driver controls the steering wheel during high-speed driving, it offers weighty steering feel and stability.
How to operate R - MDPS
  1. When the driver controls the steering wheel during driving, the steering force is transmitted to the steering column and the universal joint.
  2. MDPS ECU controller receives the signals from the vehicle speed, torque, and steering angle sensors.
  3. Electrical motor works based on the operation value of the signals.
  4. The rack bar in the steering gear moves left and right by the driver’s power to turn the steering wheel and the driving torque of the motor. At this time, the rack bar pushes and pulls the tires, so the tires rotate.
    1. Steering Wheel
    2. Steering Column
    3. Universal Joint
    4. Steering Gear Box
    5. Tire Rotation
    6. Torque Sensor
    7. MDPS Power Pack (ECU + Motor)
    8. Reduction Gear

    Functions of the main components (MDPS Power Pack):
    • ECU: It receives the driver’s steering from the sensor and calculates the rotation force for electric drive motor.
    • Electric drive motor: It generates the drive torque through the value calculated by ECU’s control.

On Vechicle Inspection. MDPS Column and Housing Components and Components Location

On Vechicle Inspection

On Vehicle Inspection

  1. Diagnostic equipment (KDS) can be used to diagnose fault parts quickly. (Refer to "DTC Diagnostic Guide")
    1. Self diagnosis : Inspection and display fault code (DTC) (Refer to DTC guide when fault code is found.)
    2. S/W Management : Controlling other features including system option setting and zero point adjustment. (S/W Management → EPS - Power Steering → Steering Angle Sensor(SAS) Calibration (S/W Management → EPS - Power steering → MDPS Tuning Data Setting)
      Refer to the KDS screen for operating conditions and details
If the MDPS warning light does not illuminate, the following symptoms are normal :
  • Immediately after starting the engine, there is no temporary auxiliary steering force during the MDPS system self-diagnosis time (about 2 seconds), but this is not a malfunction.
  • Noise due to relay connection on engine On or Off, but this is normal operating sound.
  • Noise due to motor rotation during steering or low-speed driving, but this is normal operating sound.

MDPS Column and Housing Components and Components Location

Component

Manual Tilt and Telescopic Type
1. Steering Column Assembly
1-a. 53.9 - 59 N·m
1-b. 24.5 - 29 N·m

Electrical Tilt and Telescopic Type
1. Steering Column Assembly
1-a. 53.9 - 59 N·m
1-b. 24.5 - 29 N·m

MDPS Column and Housing On Vehicle Inspection

On Vehicle Inspection

  1. Check the steering column for damage and deformation.
  2. Check the joint bearing for damage and wear.
  3. Check the tilt bracket for damage and cracks.

MDPS Column and Housing Removal and Installation

Removal

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Align the steering wheel straight.
  2. Secure the steering wheel to prevent movement.
    Changing the clockspring neutral position by rotating the steering wheel with the steering column universal joint removed may result in open circuit and faulty folding of the cable inside the clockspring after installation.
  3. Disconnect the battery negative ( - ) terminal and the service interlock connector. (Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD") (Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
  4. Remove the multifunction switch. (Refer to Body - "Multifunction Switch")
  5. Remove the Cluster Unit. (Refer to Body - "Cluster Unit")
  6. Remove the universal joint assembly bolt (A).

    Tightening torque : 49.0 - 59 N·m

    Do not reuse the universal joint assembly bolt.
  7. Remove the wiring clip (A).
    Clip Positions (A)
  8. Disconnect the electric tilt and telescopic steering column motor connectors (A).[if equipped]
  9. Remove the column housing bolt (A).

    Tightening torque : 53.9 - 59 N·m

  10. Remove the column housing assembly after removing the nuts (A).

    Tightening torque : 24.5 - 29 N·m

Installation

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Install in the reverse order of removal.
    • Install to the specified torque.
    • When assembling the steering column, insert the dowel pin (A) well into the MDPS bracket groove (B).
    • Tighten the steering gear joint by firmly inserting it into the steering gearbox pinion shaft during installation.
    • Make sure that the universal joint bolt head faces the driver when installing.
  2. Perform the order below with the KDS. (S/W Management → EPS - Power steering → MDPS Tuning Data Setting) (S/W Management → EPS - Power Steering → Steering Angle Sensor(SAS) Calibration (S/W Management → SCM - Steering Column Module → Steering Limit Position Setting) [If equipped]
    Refer to the KDS screen for operating conditions and details

Universal joint assembly Components and Components Location. Universal joint assembly On Vechicle Inspection

Universal joint assembly Components and Components Location

Component

1. Universal Joint Assembly
1-a. 49.0 - 59 N·m
1-b. 12.7 - 17,7 N·m
1-c. 49.0 - 59 N·m

Universal joint assembly On Vechicle Inspection

On Vehicle Inspection

  1. Check the bolts tightening condition of the universal joint.
  2. Check if the universal joint is damaged or worn.

Universal joint assembly Removal and Installation

Removal

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Align the steering wheel straight.
  2. Secure the steering wheel to prevent movement.
    Changing the clockspring neutral position by rotating the steering wheel with the steering column universal joint removed may result in open circuit and faulty folding of the cable inside the clockspring after installation.
  3. Remove the front trunk. (Refer to Body - "Front Trunk")
  4. Separate the steering universal joint from the steering gear box.
    1. Remove the steering universal joint bolt (A).

      Tightening torque : 49.0 - 59 N·m

      Do not reuse the steering universal joint bolt.
    2. Separate the steering universal joint (A) in the direction of the arrow.
  5. Remove the crash pad lower panel. (Refer to Body - "Crash Pad Panel")
  6. Remove the universal joint assembly bolt (A).

    Tightening torque : 49.0 - 59 N·m

    Do not reuse the universal joint assembly bolt.
  7. Remove the universal joint assembly (A) after removing the nuts.

    Tightening torque : 12.7 - 17,7 N·m

Installation

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Install in the reverse order of removal.
    • Install to the specified torque.
    • Insert the universal joint assembly securely into the steering gearbox pinion shaft.
    • Make sure that the universal joint bolt head faces the driver when installing.

Steering Gear Box Components and Components Location

Component

1. Tie Rod End
1-a. 49.0 - 54 N·m
2. Steering Gear Box
2-a. 107.9 - 128 N·m
3. Front Sub Frame

Steering Gear Box Removal and Installation - 2WD

Removal

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Remove the front subframe. (Refer to Suspension System - "Front Subframe")
  2. Remove the steering gear box (A) after removing the bolts.

    Tightening torque : 107.9 - 128 N·m

    When installing the steering gear box, pre-tighten all bolts and tighten to the specified torque.

Installation

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Install in the reverse order of removal.
    Install to the specified torque.
  2. Perform the order below with the KDS. (S/W Management → EPS - Power steering → MDPS Tuning Data Setting) (S/W Management → EPS - Power Steering → Steering Angle Sensor(SAS) Calibration
    Refer to the KDS screen for operating conditions and details
  3. Check the alignment. (Refer to Suspension System - "Alignment")
  4. Perform Over The Air (OTA) controller S/W update with KDS. (Refer to Body - "Over The Air (OTA)")

Steering Gear Box Removal and Installation - 4WD

Removal

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Remove the front motor and reduction gear assembly. (Refer to Front Motor and Reduction Gear System - "Front Motor and Reduction Gear Assembly")
  2. Remove the steering gear box (A) after removing the bolts.

    Tightening torque : 107.9 - 128 N·m

    When installing the steering gear box, pre-tighten all bolts and tighten to the specified torque.

Installation

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Install in the reverse order of removal.
    Install to the specified torque.
  2. Perform the order below with the KDS. (S/W Management → EPS - Power steering → MDPS Tuning Data Setting) (S/W Management → EPS - Power Steering → Steering Angle Sensor(SAS) Calibration
    Refer to the KDS screen for operating conditions and details
  3. Check the alignment. (Refer to Suspension System - "Alignment")
  4. Perform Over The Air (OTA) controller S/W update with KDS. (Refer to Body - "Over The Air (OTA)")

Tie Rod End Removal and Installation

Special Service Tool

Tool Name / Number Illustration
Ball joint puller
09568 - 2J100
Used for removal of tie rod end

Removal

Tie rod end
  1. Remove the front wheel and tires. (Refer to Suspension System - "Wheel")
  2. Separate the tie rod end ball joint using the SST.
    1. Remove the split pin (A).
    2. Remove the lock nut (B), and washer (C).

      Tightening torque : 98.1 - 118 N·m

      • Do not reuse the split pin.
      • Do not reuse the lock nut.
      • Be careful not to damage the boot of the link.
      • Always use hand tools when removing and installing the lock nut.
    3. Separate the tie rod end ball joint (A) using SST (09568 - 2J100).
  3. Loosen the tie rod end lock nut (A) until the tie rod end can rotate.
    Pre-tightening torque : 2.9 - 9,8 N·m Tightening torque : 49.0 - 54 N·m
    Measure the thread length (A) or mark the mounting position of the lock nut (B) before removing.
  4. Remove the tie rod end (A) by turning it counterclockwise.

Installation

  1. Install in the reverse order of removal.
    Tighten the bolts and nuts to the specified torque.
  2. Check the alignment. (Refer to Suspension System - "Alignment")