Steering System

Steering Wheel

57steps
~342min
4/5difficulty
0204060801004936N·mlb·ft
Tightening torque found on this page
Done 0 of 57

Contents:

Components and Components Location

Component

Standard

1. Driver Air Bag (DAB) Module
2. Steering Wheel Bezel
3. Haptic Motor
4. Hands on Detection (HoD) Controller
5. Steering Wheel Body
5-a. 39.3 - 49 N·m
6. Dynamic Damper
7. Paddle Shift Switch
8. Steering Wheel Extension Wire
9. Steering Wheel Lower Cover

GT-line
1. Driver Airbag (DAB)
2. Steering Wheel Bezel
3. Drive Mode Switch
4. Steering Wheel Remote Control (SWRC) Switch
5. Horn Plate
6. Steering Wheel Body
6-a. 39.3 - 49 N·m
7. Hands on Detection (HoD) Controller
8. Haptic Motor
9. Paddle Shifter Switch
10. Steering Wheel Extension Wire
11. Steering Wheel Lower Cover

Removal and Installation

Removal

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.

Standard

  1. Align the steering wheel straight.
  2. Disconnect the battery negative ( - ) terminal and the service interlock connector. (Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD") (Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
  3. Secure the steering wheel to prevent movement.
  4. Remove the driver airbag module. (Refer to Restraint - "Driver Airbag (DAB)")
  5. Disconnect the steering wheel connector (A).
  6. Remove the steering wheel (A) after removing the bolt.

    Tightening torque : 39.3 - 49 N·m

    • Do not use a hammer when removing steering wheel, the steering column may be damaged if using a hammer.
    • Do not reuse the steering wheel bolt.
  7. Align the steering wheel straight.
  8. Disconnect the battery negative ( - ) terminal and the service interlock connector. (Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD") (Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
  9. Secure the steering wheel to prevent movement.
  10. Remove the driver airbag module. (Refer to Restraint - "Driver Airbag (DAB)")
  11. Disconnect the steering wheel connector (A).
  12. Remove the steering wheel (A) after removing the bolt.

    Tightening torque : 39.3 - 49 N·m

    • Do not use a hammer when removing steering wheel, the steering column may be damaged if using a hammer.
    • Do not reuse the steering wheel bolt.
GT-line

Installation

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Install in the reverse order of removal.
    • Install to the specified torque.
    • Do not reuse the steering wheel bolt.
    • Match the 3 marks when installing. (For a new one, mark 3 points same as the old one.)

Disassembly and Reassembly

Disassembly

Standard

  1. Remove the paddle shift switch mounting screws (A).
  2. Separate the paddle shifter switch (A) with a suitable tool.
  3. Disconnect the paddle shift connectors (B), and then remove the paddle shift switches (A).
  4. Remove the steering wheel lower cover (A) after removing the screws.
  5. Disconnect the remote control switch connectors (A).
  6. Disconnect the heated steering wheel connector (A).
  7. Remove the extension wiring ground screw (A).
  8. Remove the steering wheel dynamic damper (A) after removing the screws.
  9. Disconnect the Hands on Detection (HoD) controller connector (A).
  10. Disconnect the haptic motor connector (A).
  11. Remove the steering wheel extension wiring (A).
  12. Remove the Steering Wheel Remote Control (SWRC) switch and bezel screws (A).
  13. Remove the steering wheel remote control (SWRC) switch and bezel (A).
  14. Remove the haptic motor (A) after removing the screws.
  15. Remove the steering wheel remote control (SWRC) switch screws (A).
  16. Remove the steering wheel remote control (SWRC) switches (A).
  17. Remove the paddle shift switch mounting screws (A).
  18. Separate the paddle shifter switches (A).
  19. Remove the paddle shift switches (A) after disconnecting the paddle shift connectors (B).
  20. Remove the horn plate screws (A).
  21. Disconnect the horn connector (A), and then remove the horn plate (B).
  22. Remove the steering wheel lower cover (A) after removing the screws.
  23. Disconnect the haptic motor connector (A).
  24. Remove the haptic motor (A) after removing the screws.
  25. Disconnect the remote control switch connectors (A).
  26. Disconnect the heated steering wheel connector (A).
  27. Separate the hands on detection (HoD) controller (A).
  28. Disconnect the hands on detection (HoD) controller connector (A).
  29. Remove the hand on detection (HoD) controller after disconnecting the connector (A).
  30. Remove the extension wiring ground screw (A).
  31. Disconnect the drive mode switch connector (A).
  32. Remove the steering wheel extension wiring (A).
  33. Remove the steering wheel remote control (SWRC) switch and bezel screws (A).
  34. Remove the steering wheel remote control (SWRC) switch and bezel (A).
  35. Remove the steering wheel remote control (SWRC) switch screws (A).
  36. Remove the steering wheel remote control (SWRC) switches (A).
  37. Remove the drive mode switch screws (A).
  38. Remove the drive mode switch (A).
  39. Remove the steering wheel bezel (A) after removing the screws.
GT-line

Reassembly

  1. Reassemble in the reverse order of disassembly.
    • When assembling the steering wheel, be careful not to damage the parts by tightening with excessive torque.
    • Disconnection or short circuit may occur if the main wiring is not held in place when mounting the steering wheel lower cover.
  2. Perform Over The Air (OTA) controller S/W update with KDS if the HoD controller is replaced with a new one. (Refer to Body - "Over The Air (OTA)")

Heated steering wheel Components and Components Location. Heated steering wheel Removal and Installation

Heated steering wheel Components and Components Location

Component

1. Heated Steering Wheel Control Unit (Integrated with Powernet Domain Controller)
2. Heated steering Wheel Control Switch (Integrated with Floor Console Switch)

Heated steering wheel Removal and Installation

Removal

Heated Steering Wheel Control Unit

The heated steering control unit is integrated with the powernet domain controller (PDC), so replace the PDC.
  1. Remove the powernet domain controller. (Refer to Body - "Junction Block")

Heated Steering Switch

The heated steering switch is integrated with the floor console switch, so replace the floor console switch.
  1. Remove the floor console switch. (Refer to Body - "Floor Console Switch")

Installation

  1. Install in the reverse order of removal.

Paddle Shifter Switch Removal and Installation

Removal

  • When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shocks or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the driver airbag module. (Refer to Restraint - "Driver Airbag (DAB)")
    If the airbag is deployed, there may be a risk of injury, so always store the detached airbag module with the cover facing upwards.
  2. Remove the paddle shift switch mounting screws (A). [LH] [RH]
  3. Separate the paddle shifter switch (A) with a suitable tool. [LH] [RH]
  4. Disconnect the paddle shifter switch connector (B) then remove the paddle shifter switch (A). [LH] [RH]

Installation

  • When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shocks or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
    Install to the specified torque.