Steering System

Components and Components Location. Specification

14steps
~84min
3/5difficulty
010203040504.23N·mlb·ft
Tightening torque found on this page
Done 0 of 14

Contents:

Components and Components Location. Specification

Components and Components Location

Component

1. Steering Column Module (SCM)
1-a. 3.9 - 4,2 N·m (0.4 - 0.43 kgf·m, 2.9 - 3.1 lb·ft, 34.7 - 37.3 lb·in)

Specification

Specification

Steering Column Module (SCM)
Item Specification
Rated voltage (V) 12
Operation voltage (V) 9 - 16
Operating temperature [°C (°F)] -30 to 75 (-22 to 167)
Storage temperature (°C [°F]) -40 to 85 (-40 to 185)
Parasitic Current (mA) Maximum 0.7

Description and Operation

Description

The Steering Column Module (SCM) stores the optimal steering column position set by the driver in the tilt and telescope unit by IMS switch operation and can play it back to the position set by the driver with the IMS switch even if the position of the steering column changes. For safety, it has a function of prohibiting operations while driving and urgently stopping operations depending on the situation.

Function

  1. Manual Operating
    • Tilt and telescopic control by operating the manual switch.
    • When the manual switch signal is input, the relay is activated to change the steering column position.
  2. Memory
    • It memorizes and operates the tilt and telescopic positions of 2 drivers.
    • When the driver operates the IMS switch, the stored steering column position is received from the Body Domain Control (BDC) unit via CAN data to operate.
    • Operation by CAN data received when IMS switch input signal.
  3. Door open/close operation : It is the operating function according to driver door OPEN/CLOSE (received CAN data from BDC )

Removal and Installation

Removal

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Steering Column Module (SCM)
  1. Disconnect the battery negative ( - ) terminal and the service interlock connector. (Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD") (Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
  2. Remove the glove box housing. (Refer to Body - "Glove Box")
  3. Disconnect the steering column module connector (A) and wiring clip (B).
  4. Remove the steering column module after removing the nuts (A).
    Tightening torque : 3.9 - 4,2 N·m (0.4 - 0.43 kgf·m, 2.9 - 3.1 lb·ft, 34.7 - 37.3 lb·in)
  5. Remove the steering column lower shroud panel. (Refer to Body - "Steering Column Shroud Panel")
  6. Separate the steering column module switch connector clip (A).
  7. Remove the steering column module switch (B) pushing in direction of the arrow while pressing the hinges (A).
Steering Column Module (SCM) Switch

Installation

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Steering Column Module (SCM)
  1. Install in the reverse order of removal.
    Install to the specified torque.
  2. Perform the order below with the KDS. (S/W Management → SCM - Steering Column Module → Steering Limit Position Setting)
    Refer to the KDS screen for operating conditions and details
  3. Perform Over The Air (OTA) controller S/W update with KDS. (Refer to Body - "Over The Air (OTA)")
  4. Install in the reverse order of removal.
    • Install to the specified torque.
    • Match the grooves of the switch (A) and the lower shroud panel (B) when installing.
Steering Column Module (SCM) Switch