Restraint

Seat Belt System

24steps
~144min
4/5difficulty
02040608010053.940N·mlb·ft
Tightening torque found on this page
Done 0 of 24

Contents:

Description and Operation. On Vehicle Inspection

Description and Operation

Description

  1. Seat Belt Pretensioner (BPT)
    • When a collision occurs, the seat belt pretensioner winds the seat belt and prevents the driver's and front passenger's body from being leaned forward and collided with the interior parts of the vehicle.
    • The seat belt pretensioner operates with airbags.
    The seat belt pretensioner generates heat when activated, so do not touch it for several minutes after activation.
  2. Seat Belt Reminder
    • This is a function that informs the driver whether or not a passenger is wearing a seat belt while stopping or driving.
    • When POWER ON regardless of whether the seat belt is fastened, the seat belt warning light turns on for 3 - 6 seconds and then turns off.

On Vehicle Inspection

On Vehicle Inspection

Diagnosis with KDS
  1. The seat belt system can be more quickly diagnosed for problems with the KDS (Refer to "DTC guide").
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found)

Height Adjust Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the center pillar upper trim. (Refer to Body - "Center Pillar Trim")
  2. Separate the seat belt (A) after removing the bolt.

    Tightening torque : 39.2 - 54 N·m

  3. Remove the height adjust (A) after removing the bolts.

    Tightening torque : 39.2 - 54 N·m

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Seat Belt Pretensioner (BPT) Troubleshooting

Troubleshooting

Direct measuring the resistance of the seat belt pretensioner is very dangerous as it can cause the seat belt pretensioner to deploy.

Seat Belt Pretensioner (BPT) Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Use KDS to proceed with fault diagnosis and check that the seat belt operates normally, after a collision. Replace it with a new one if necessary.
Front Seat Belt Pretensioner (BPT)
  1. Remove the center pillar lower trim. (Refer to Body - "Center Pillar Trim")
  2. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
    1. Open the front trunk (A).
    2. Open the auxiliary 12 V battery service cover (A).
    3. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

      Tightening torque : 7.8 - 9,8 N·m

    4. Disconnect the service interlock connector (A).
      • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
      • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
      The service interlock connector cannot be completely removed.
  3. Disconnect the BPT connector (A).
  4. Remove the BPT (A) after removing the bolt.

    Tightening torque : 44.1 - 55 N·m

  5. Remove the rear pillar trim. (Refer to Body - "Rear Pillar Trim")
  6. Remove the BPT (B) after disconnecting the connector (A) and removing the bolt.

    Tightening torque : 44.1 - 55 N·m

Rear Seat Belt Pretensioner (BPT)

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
    Be sure to keep the torque specifications presented in shop manuals. Otherwise, it could lead to the malfunction of airbag system.
  2. Check that the airbag system operates normally.
    When POWER ON, the airbag warning light should turns off after turning on for 3 - 6 seconds.

Seat Belt Reminder Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
The indication below represents the location of a clip or fastener.
Front Seat Belt Buckle
  1. Remove the front seat assembly. (Refer to Body - "Front Seat Assembly")
  2. Separate the connector wiring after removing the fasteners (A).
  3. Remove the buckle (A) after removing the bolt.

    Tightening torque : 44.1 - 54 N·m

  4. Remove the rear seat back assembly. [Driver's side] (Refer to Body - "Rear Seat Assembly")
  5. Separate the connector wiring (A) after removing the fasteners.
  6. Remove the buckle (A) after removing the bolt.

    Tightening torque : 44.1 - 54 N·m

  7. Remove the rear seat back assembly. [Passenger's side] (Refer to Body - "Rear Seat Assembly")
  8. Separate the connector wiring (A) after removing the fasteners.
  9. Remove the buckle (A) after removing the bolt and nut.

    Tightening torque : 44.1 - 54 N·m

Rear Seat Belt Buckle [Driver's Side] Rear Seat Belt Buckle [Passenger's Side]

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  2. Check that the airbag system operates normally.
    When POWER ON, the airbag warning light should turns off after turning on for 3 - 6 seconds.