Restraint

Components and Components Location. Description and Operation

38steps
~228min
4/5difficulty
010203040509.87N·mlb·ft
Tightening torque found on this page
Done 0 of 38

Contents:

Components and Components Location. Description and Operation

Components and Components Location

Component

1. Driver Airbag (DAB)
2. Clock Spring
3. Passenger Airbag (PAB)
4. Side Airbag (SAB) [Driver's Side]
5. Side Airbag (SAB) [Passenger's Side]
6. Curtain Airbag (CAB)

Description and Operation

Description

  • The airbag plays a role in protecting the driver by deploying in the event of a severe collision or rollover accident.
  • The airbag consists of driver, knee, and passenger airbags deployed in frontal collisions and side and curtain airbags deployed in side collisions or rollover accidents.

On Vehicle Inspection

On Vehicle Inspection

Diagnosis with KDS
  1. The airbag module can be more quickly diagnosed for problems with the KDS (Refer to "DTC guide").
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found)

Airbag Module Disposal Procedure

Airbag Module Disposal Procedure

When scrapping a vehicle equipped with an airbag system such as an airbag or seat Belt Pretensioner (BPT), the airbag must be deployed first. When deploying the airbag, it must be deployed by a skilled technician, and the used airbag cannot be reused, so it must not be installed in another vehicle.
  • If an undeployed airbag is accidentally deployed, it may cause serious injury, so it must be disposed after deployment.
  • Deployment of the airbag must be performed on a level ground with no risk elements.
  • An explosion sound occurs when the airbag is deployed, perform it in a place where there is no damage to the surroundings.
  • Smoke may occur when the airbag is deployed, perform the deployment of the airbag in area with good ventilation and no smoke detector nearby.
  • The airbag is very hot after deploying, so wait at least 30 minutes and let it cool before touching it.
  • Keep the deployed airbag away from water.
  • When scrapping a vehicle, the airbag should, in principle, be deployed while installed in the vehicle. Do not remove the airbag except unavoidable circumstances.
  • If the airbag is removed from the vehicle due to airbag replacement (accident repair, warranty repair, etc.), refer to the relevant manual and deploy it outside the vehicle. (Deploying the airbag inside the vehicle may cause damage to the vehicle.)
  • Do not disassemble the airbag.
  • Be careful not to damage the airbag.
  • Be careful not to drop the airbag.
  • When deploying the airbag, deploy it at least 7 m (22.97 ft.) away from the airbag.
  • When deploying the airbag, always use the special tool and perform it in a place without electrical noise.
  • Wash hands thoroughly with soap after deploying, repacking, and disposal of the airbag.
  • Always wear protective gloves, goggles and earplugs when deploying the airbag.
Tools and Equipment Required for Disposal of Airbag Modules
Illustration Name Possible Cause
Gloves
Goggles
Earplugs
2 tires with wheels (Top / Bottom)
3 tires without the wheels (Middle)
Rope Strap / Ratchet Strap (Use for connecting the airbag equipment and tires according to the deployment instructions)
12 V battery

Deployed Inside the Vehicle
  1. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
    1. Open the front trunk (A).
    2. Open the auxiliary 12 V battery service cover (A).
    3. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

      Tightening torque : 7.8 - 9,8 N·m

    4. Disconnect the service interlock connector (A).
      • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
      • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
      The service interlock connector cannot be completely removed.
  2. Make sure the airbag is securely installed.
  3. Prepare to deploy the airbag module as follows.
    1. Disconnect the airbag or seat belt pretensioner connector to be deployed.
    2. Connect the deployment adapter to the airbag or seat belt pretensioner.
      • For the Driver Airbag (DAB), disconnect the connector, connect the deployment adapter, and then reinstall it on the steering wheel.
      • When using the deployment adapter, use it appropriately according to the deployment airbag.
      • DAB, PAB, CAB, BPT (0K57A - 3U100A)
      • SAB (0957A - 2W100)
      • For the Driver Airbag (DAB), disconnect the 2-pin connector, connect the deployment adapter, and then reinstall it on the steering wheel.
  4. Workers should be at least 7 meters away from the vehicle.
  5. Connect the Special Service Tool (0957A - 34100A) to the deployment adapter and then connect it to the external battery.
    1. Battery (12 V)
    2. The Special Service Tool for deployment (0957A - 34100A)
    3. Deployment adapter
  6. Activate the switch of the airbag deployment tool to deploy the airbag.
    1. When connecting to an external battery normally , POWER ON (1) is turned on.
    2. If READY (2) button illuminates while pressing READY (2) button, press DEPLOY (3) button to deploy the airbag.
      When the airbag is deployed, loud noise is generated, visually confirmed, and after rapid inflation, it contracts slowly.
  7. Place the deployed airbag in a sturdy plastic bag and sealed securely, then dispose it.
  8. After spreading the rope (A) on the floor in a cross shape, put the tire (B) equipped with the wheel on the floor.
  9. Connect the deployment adapter (A) to the airbag or pretensioner.
    • For the Driver Airbag (DAB), disconnect the connector, connect the deployment adapter, and then reinstall it on the steering wheel.
    • When using the deployment adapter, use it appropriately according to the deployment airbag.
    • DAB, PAB, CAB, BPT (0K57A - 3U100A)
    • SAB (0957A - 2W100)
    • KAB (0957A - 3F100)
  10. Fix the airbag or pretensioner (A) to the wheel. Airbag
    If the airbag deployment surface faces downward instead of upward, the airbag may spring up and cause serious injury to the worker.
    Pretensioner
    Install the end of the piston tube of the anchor pretensioner, facing the floor.
  11. After putting the three waste tires (A), put the tire (B) with the wheel on it.
  12. Fix the tire by using the ratchet strap (C).
  13. After connecting the battery, connect the airbag deployment tool (0957A - 34100A) to the deployment adapter.
  14. Activate the switch of the airbag deployment tool to deploy the airbag.
    1. When connecting to an external battery normally, POWER ON (1) is turned on.
    2. If the READY (2) button illuminates while pressing the READY (2) button, press DEPLOY (3) button to deploy the airbag.
    When the airbag is deployed, loud noise is generated, visually confirmed, and after rapid inflation, it contracts slowly.
  15. Place the deployed airbag in a sturdy plastic bag and sealed securely, then dispose it.
Deployment outside of the vehicle

Clock Spring Description and Operation. Clock Spring Troubleshooting

Clock Spring Description and Operation

Description

The clock spring is a device that transmits the operation signal generated from the sensors installed on the front and side of the vehicle to the inflator (gas generator) of the airbag via the internal cable. It also transmits the steering wheel remote control switch and horn operation signals to the system via the internal cable.
If the airbag is deployed due to an accident, the clock spring cannot be repaired or reused because there is a possibility of damage to the clock spring due to heat and impact caused by the explosion of the airbag inflator (gas generating device). Be sure to replace with a new one.

Clock Spring Troubleshooting

Troubleshooting

Airbag Warning Light On Noise

Clock Spring Replacement. Curtain Airbag (CAB) Troubleshooting

Clock Spring Replacement

Replacement

The clock spring cannot be replaced individually due to included in the multifunction switch. If necessary, replace the multifunction switch.
  1. Replace the multifunction switch. (Refer to Body - "Multifunction Switch")

Curtain Airbag (CAB) Troubleshooting

Troubleshooting

Direct measuring the resistance of the airbag is very dangerous as it can cause the airbag deployment.

Curtain Airbag (CAB) Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
The procedure for removing the Curtain Airbag (CAB) below is for driver's side. Opposite airbag are performed in the same procedures.
  1. Remove the roof trim. (Refer to Body - "Roof Trim Assembly")
  2. Disconnect the CAB connector (A).
  3. Remove the CAB (A) after removing the bolts and nuts.
    Tightening torque Bolt : 7.8 - 11,8 N·m Nut : 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
    • Be sure to keep the torque specifications presented in shop manuals. Otherwise, it could lead to the malfunction of airbag system.
    • Use the color of sentence and line on a airbag to identify curtain airbag module. Driver's side : Yellow label (attached to plastic cover) Passenger's side : Orange label (attached to plastic cover)
    • Be careful not to twist when the curtain airbag module installing. The curtain airbag module may not deploy normally if twisted.
  2. Check that the airbag system operates normally.
    When POWER ON, the airbag warning light should turns off after turning on for 3 - 6 seconds.

Driver Airbag (DAB) Troubleshooting

Troubleshooting

Direct measuring the resistance of the airbag is very dangerous as it can cause the airbag deployment.

Driver Airbag (DAB) Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
    1. Open the front trunk (A).
    2. Open the auxiliary 12 V battery service cover (A).
    3. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

      Tightening torque : 7.8 - 9,8 N·m

    4. Disconnect the service interlock connector (A).
      • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
      • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
      The service interlock connector cannot be completely removed.
  2. Remove the Driver Airbag (DAB) by pressing the lock levers (B) using the service hole (A). How to Release the Lock Levers When Removing the DAB Module and How to Install It (Play ▶)

    Video: How to Release the Lock Levers When Removing the DAB Module and How to Install It

    Notes When Refering Video This video helps clearly identify areas that are hard to distinguish in manual images, such as component locations or assembly structures. It also allows visual confirmation of areas that are difficult to see directly due to restricted visibility caused by surrounding components, from a technician’s perspective.
    • This video is created using common specifications and may differ from the actual vehicle.
    • The location and repair procedures of the parts may vary depending on vehicle model, model year, region, and specifications.
    • Check the KDS Guide for detailed information on how to use the KDS.
    • Check the manual for detailed maintenance procedures.
    • Unauthorized reproduction, distribution, or sharing of this video is prohibited.
  3. Remove the (DAB) (A).
  4. Disconnect the DAB connector (A) and horn connector (B).

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
    When installing the Driver Airbag (DAB) to the steering wheel, make sure that the airbag wire is not caught in the steering wheel's internal structure.
  2. Check the airbag system and horn operate normally.
    When POWER ON, the airbag warning light should turns off after turning on for 3 - 6 seconds.

Passenger Airbag (PAB) Troubleshooting

Troubleshooting

Direct measuring the resistance of the airbag is very dangerous as it can cause the airbag deployment.

Passenger Airbag (PAB) Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the crash pad assembly. (Refer to Body - "Crash Pad Assembly")
  2. Remove the Passenger Airbag (PAB) (A) after removing the bolts.
    Tightening torque : 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
    Be sure to keep the torque specifications presented in shop manuals. Otherwise, it could lead to the malfunction of airbag system.
  2. Check that the airbag system operates normally.
    When POWER ON, the airbag warning light should turns off after turning on for 3 - 6 seconds.

Side Airbag (SAB) Troubleshooting

Troubleshooting

Direct measuring the resistance of the airbag is very dangerous as it can cause the airbag deployment.

Side Airbag (SAB) Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
When replacing the airbag due to a deployment of the airbag, replace the seat bag assembly.
The indication below represents the location of a clip or fastener.
Front Side Airbag (SAB)
  1. Remove the front seat back cover assembly. (Refer to Body - "Front Seat Back Cover Assembly")
  2. Separate the Side Airbag (SAB) after removing the nuts (A).
    Tightening Torque : 5.9 - 7,8 N·m (0.6 - 0.8 kgf·m, 4.3 - 5.8 lb·ft, 52.1 - 69.4 lb·in)
  3. Remove the SAB (A) after removing the fasteners.
  4. Remove the rear seat back cover assembly. (Refer to Body - "Rear Seat Back Cover Assembly")
  5. Separate the SAB connector (A).
  6. Remove the SAB (A) after removing the nuts.
    Tightening Torque : 5.9 - 7,8 N·m (0.6 - 0.8 kgf·m, 4.3 - 5.8 lb·ft, 52.1 - 69.4 lb·in)
Rear Side Airbag (SAB)

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
    • Be sure to keep the torque specifications presented in shop manuals. Otherwise, it could lead to the malfunction of airbag system.
    • Since improper installation of the front seat back cover will prevent the normal deployment of the side airbags, make sure that the front seat back cover is properly installed.
  2. Check that the airbag system operates normally.
    When POWER ON, the airbag warning light should turns off after turning on for 3 - 6 seconds.