1. Front Impact Sensor (FIS) 2. Pressure type Side Impact Sensor (P-SIS) 3. Front Acceleration type Side Impact Sensor (A-SIS)
4. Rear Acceleration Type Side Impact Sensor (A-SIS) 5. Airbag Control Unit (ACU)
Description and Operation
Description
Airbag Control Unit (ACU)
The airbag control unit determines whether and when to deploy the airbag and the seat belt pretensioner.
It supplies the power required for deployment at the time of deployment of the airbag or seat belt pretensioner.
The airbag control unit main functions.
Collision detection and passenger boarding detection.
Rollover accident detection.
Airbag system self diagnosis.
When a fault in the airbag system, displayed a warning light.
When an accident the vehicle, supply of high-voltage cut-off signal.
Front Impact Sensor (FIS) : When the event of a head-on collision, the airbag control unit uses the front impact sensor signal to determine whether and when to deploy the driver airbag, passenger airbag, knee airbag, and seat belt pretensioner.
Side Impact Sensor (SIS)
The side impact sensor consists of the pressure type side impact sensor sensing the collision pressure, and the acceleration type side impact sensor sensing the collision acceleration.
When the event of a side collision, the SRS control module uses the side impact sensor signal to determine whether and when to deploy the side airbag, curtain airbag.
Occupant Detective System (ODS)
The occupant detecting system classifies passenger seats (vacant seats, child seats and children / adults) and sends passenger information to the airbag control unit.
The airbag control unit uses passenger information and collision signals to determine whether to deploy the passenger airbag.
Acceleration type Side Impact Sensor (A-SIS) On Vehicle Inspection
On Vehicle Inspection
Diagnosis with KDS
The side impact sensor can be more quickly diagnosed for problems with the KDS (Refer to "DTC guide").
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found)
Acceleration type Side Impact Sensor (A-SIS) Removal and Installation
Removal
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Front Acceleration Type Side Impact Sensor (A-SIS)
Remove the center pillar lower trim. (Refer to Body - "Center Pillar Trim")
Remove the A-SIS (B) by removing the nut after disconnecting the connector (A).
Tightening torque : 7.5 - 9,1 N·m
Remove the luggage side trim. (Refer to Body - "Luggage Side Trim")
Remove the A-SIS (B) by removing the nut after disconnecting the connector (A).
Tightening torque : 7.5 - 9,1 N·m
Rear Acceleration Type Side Impact Sensor (A-SIS)
Installation
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Install in the reverse order of removal.
Be sure to keep the torque specifications presented in shop manuals. Otherwise, it could lead to the malfunction of airbag system.
Check that the airbag system operates normally.
When POWER ON, the airbag warning light should turns off after turning on for 3 - 6 seconds.
Airbag Control Unit (ACU) On Vehicle Inspection
On Vehicle Inspection
Diagnosis with KDS
The airbag control unit can be more quickly diagnosed for problems with the KDS (Refer to "DTC guide").
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found)
S/W Management : Controlling other features including system option setting and zero point adjustment. (S/W Management → Airbag → ACU Variant Coding)
Refer to the KDS screen for operating conditions and details.
Airbag Control Unit (ACU) Removal and Installation
Removal
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Airbag Control Unit (ACU)
Remove the floor console assembly. (Refer to Body - "Floor Console Assembly")
Disconnect the ACU connectors (A).
Remove the ACU (A) after removing the nuts.
Tightening Torque : 7.7 - 9,5 N·m
Installation
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
For airbag control units with a rollover detection feature, the airbag may deploy due to movements occurring during installation. Therefore, do not install the airbag control unit with the battery connected or within 3 minutes and 30 seconds of disconnecting the battery negative ( - ) terminal.
Install in the reverse order of removal.
Perform the order below with the KDS when replacing the airbag control unit. (S/W Management → Airbag → ACU Variant Coding)
Refer to the KDS screen for operating conditions and details.
Check that the airbag system operates normally.
When POWER ON, the airbag warning light should turns off after turning on for 3 - 6 seconds.
Perform Over The Air (OTA) controller S/W update with KDS. (Refer to Body - "Over The Air (OTA)")
Front Impact Sensor (FIS) On Vehicle Inspection
On Vehicle Inspection
Diagnosis with KDS
The front impact sensor can be more quickly diagnosed for problems with the KDS (Refer to "DTC guide").
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found)
Front Impact Sensor (FIS) Removal and Installation
Removal
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Front Impact Sensor (FIS)
The procedure for removing the FIS below is for driver's side. Opposite sensor are performed in the same procedures.
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
Open the front trunk (A).
Open the auxiliary 12 V battery service cover (A).
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).
Tightening torque : 7.8 - 9,8 N·m
Disconnect the service interlock connector (A).
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
The service interlock connector cannot be completely removed.
Disconnect the FIS connectors (A).
Remove the FIS (A) after removing the nuts.
Tightening torque : 7.5 - 9,1 N·m
Installation
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Install in the reverse order of removal.
Be sure to keep the torque specifications presented in shop manuals. Otherwise, it could lead to the malfunction of airbag system.
Check that the airbag system operates normally.
When POWER ON, the airbag warning light should turns off after turning on for 3 - 6 seconds.
Occupant Detecting System (ODS) On Vehicle Inspection
On Vehicle Inspection
Diagnosis with KDS
The occupant detection system can be more quickly diagnosed for problems with the KDS (Refer to "DTC guide").
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found)
S/W Management : Controlling other features including system option setting and zero point adjustment. (S/W Management → Occupant Detection System → Body Sensor Reset)
Refer to the KDS screen for operating conditions and details.
Occupant Detecting System (ODS) Removal and Installation
Removal
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Occupant Detective System (ODS) Unit
Remove the front seat assembly. [Passenger's side] (Refer to Body - "Front Seat Assembly")
Remove the unit (B) by removing the screws after disconnecting the unit connector (A).
Occupant Detective System (ODS) Sensor Mat
The ODS sensor mat cannot be replaced individually due to included in the seat cushion. If necessary, replace the seat cushion.
Remove the front seat cushion. [Passenger's side] (Refer to Body - "Front Seat Cushion Cover")
Installation
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Install in the reverse order of removal.
Perform the order below with the KDS when replacing the PODS unit. (S/W Management → Occupant Classification System → Zero Re-calibration of Occupant Classification Sensor)
After initializing the Occupant Detection System (ODS) unit, erase DTC regarding the airbag control unit and the PODS unit.
Refer to the KDS screen for operating conditions and details.
Check that the airbag system operates normally.
When POWER is ON the airbag warning light should turn off after turning on for 3 - 6 seconds.
When the ODS unit and Passenger Airbag (PAB) module are operating normally, the PAB OFF indicator lights up for 4 seconds when POWER ON, and turns on for 3 seconds when POWER OFF, then turns off.
Pressure type Side Impact Sensor (P-SIS) On Vehicle Inspection
On Vehicle Inspection
Diagnosis with KDS
The side impact sensor can be more quickly diagnosed for problems with the KDS (Refer to "DTC guide").
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found)
Pressure type Side Impact Sensor (P-SIS) Removal and Installation
Removal
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Pressure type Side Impact Sensor (P-SIS)
Remove the front door trim. (Refer to Body - "Front Door Trim")
Remove the P-SIS (B) by removing the screws after disconnecting the sensor connector (A). Tightening torque : 2.0 - 3 N·m (0.20 - 0.31 kgf·m, 1.4 - 2.2 lb·ft, 17.4 - 26.9 lb·in)
Installation
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Install in the reverse order of removal.
Be sure to keep the torque specifications presented in shop manuals. Otherwise, it could lead to the malfunction of airbag system.
Check that the airbag system operates normally.
When POWER ON, the airbag warning light should turns off after turning on for 3 - 6 seconds.