Engine Electrical System

Ignition System

26steps
~156min
4/5difficulty
0102030405011.89N·mlb·ft
Tightening torque found on this page
Done 0 of 26

Contents:

Description and Operation

Description

  • Ignition timing is controlled by electronic ignition system, and standard ignition timing data according to the engine operating condition is stored in the Engine Control Module (ECM).
  • Engine operation conditions (speed, load, temperature) are detected by various sensor. Based on these sensors ignition timing data, the primary current cut-off signal is received from the ECM to activate the ignition coil and control the ignition timing.

Troubleshooting

Troubleshooting

Engine won't start or is hard to start (cranks OK)
Suspected Cause Correction
Start / stop button fault Inspect or replace start / stop button
Ignition coil fault Inspect and replace the ignition coil
Spark plug fault Inspect and replace the spark plug
Ignition wiring disconnected or broken Repair or replace the wiring

Rough idle or stalls
Suspected Cause Correction
Ignition wiring fault Repair or replace the wiring
Ignition coil fault Inspect and replace the ignition coil

Engine hesitates or poor acceleration
Suspected Cause Correction
Spark plug fault Inspect and replace the spark plug
Ignition wiring fault Repair or replace the wiring

Poor fuel efficiency
Suspected Cause Correction
Spark plug fault Inspect and replace the spark plug

Ignition Coil Specification

Specification

Item Specification
Rated voltage (V) 14
Operating voltage (V) 4 - 16
Engine speed (rpm) 1,000 2,000 3,000 4,000 5,000 6,000
Dwell time (ms) 3.6 3.6 3.6 3.2 2.9 2.5
Secondary coil voltage (kV) 44.8 44.8 44.8 43.4 42.6 41.0

Ignition Coil Components and Components Location

Component Location

Engine Electrical System — Ignition System / Ignition Coil / Components and Components Location / Component Location illustration
1. Engine Cover 2. Ignition Coil
2-a. 9.8 - 11,8 N·m

Ignition Coil Description and Operation

Description

  • The ignition coil is a small transformer that transforms the battery voltage to 30 kV or more to create a spark in the spark plug gap in the cylinder.
  • The igniter built into the ignition coil includes the power transistor and it is an electronic switch whose electric current is controlled by the Engine Control Module (ECM) signal.
  • The ignition timing is controlled by the ECM and the standard ignition timing data according to engine operating condition is stored in the ECM memory.
  • The engine operating conditions (speed, load, warm-up state, etc.) are detected by the various sensors. Based on these sensor signals and the ignition timing data, when the ECM applies the ignition signal to the ignition coil for a certain period of time, the igniter is energized. As the current flows and rises gradually to the primary coil and the magnetic field is produced.
  • When the current in the primary coil is cut off by the ignition signal of the ECM, the rapid change of the magnetic flux by the mutual induction action is induced to the secondary coil and high voltage is generated depending on the coil winding ratio.
  • This high voltage generated from the secondary coil is caught in the spark plug gap and discharges as the electric field is destroyed to generate a spark.
Ignition Coil Schematic Diagrams
Engine Electrical System — Ignition System / Ignition Coil / Description and Operation / Description illustration

Ignition Coil Troubleshooting

Troubleshooting

Connector connection condition test
  1. Disconnect the battery negative ( - ) terminal.
  2. Remove the engine cover. (Refer to Engine Mechanical System - "Engine Cover")
  3. Re-connect the ignition coil connector (A) after disconnecting the ignition coil connector.
    Engine Electrical System — Ignition System / Ignition Coil / Troubleshooting illustration
  4. Install the engine cover. (Refer to Engine Mechanical System - "Engine Cover")
  5. Connect the battery negative ( - ) terminal.
  6. Perform the driving test after deleting the DTC code.
    Engine Electrical System — Ignition System / Ignition Coil / Troubleshooting illustration
  7. Change the misfired ignition coil (A) and normal ignition coil (B). (Refer to Ignition Coil - "Removal and Installation")
    Note
    Do not move with spark plug at the same time (move the ignition coil only)
    Engine Electrical System — Ignition System / Ignition Coil / Troubleshooting illustration
  8. Perform the driving test after deleting the DTC code.
    Engine Electrical System — Ignition System / Ignition Coil / Troubleshooting illustration
Test for changing position of each ignition coil

Ignition Coil Removal and Installation

Removal

  1. Disconnect the battery negative ( - ) terminal.
  2. Remove the engine cover. (Refer to Engine Mechanical System - "Engine Cover")
  3. Disconnect the ignition coil connectors (A).
    Engine Electrical System — Ignition System / Ignition Coil / Removal and Installation / Removal illustration
  4. Remove the ignition coils (A) after removing the bolts.

    Tightening torque : 9.8 - 11,8 N·m

    Engine Electrical System — Ignition System / Ignition Coil / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.
    Note
    • Install the ignition coil to the specified torque.
    • If the ignition coil is dropped, it may cause internal damage. (Do not reuse)
    • When installing the parts, use cloth to clean the contaminated area (A). - Use a clean and soft cloth to avoid damage. (When replacing ignition coil and spark plug together, cleaning is not required.)
      Engine Electrical System — Ignition System / Ignition Coil / Removal and Installation / Installation illustration
      Engine Electrical System — Ignition System / Ignition Coil / Removal and Installation / Installation illustration

Spark Plug Specification

Specification

Item Specification
Type ELR9IQP9+
Plug gap [mm (in.)] 0.8 - 0.9 (0.0314 - 0.0354)
Electrode material SPE Iridium

Spark Plug Components and Components Location

Component Location

Engine Electrical System — Ignition System / Spark Plug / Components and Components Location / Component Location illustration
1. Engine Cover
2. Ignition Coil
2-a. 9.8 - 11,8 N·m
3. Spark Plug
3-a. 14.7 - 24 N·m

Spark Plug Description and Operation

Description

The high voltage generated by the ignition system ignites the air mixed with the fuel at an appropriate time, and the pressure generated by the explosion of the mixture operates the piston to drive the engine.
Engine Electrical System — Ignition System / Spark Plug / Description and Operation / Description illustration

Spark Plug Troubleshooting

Troubleshooting

  1. Check the DTC code by using the KDS (Refer to "DTC guide").
    Engine Electrical System — Ignition System / Spark Plug / Troubleshooting illustration
  2. Check the ignition coil connectors (A).
    Engine Electrical System — Ignition System / Spark Plug / Troubleshooting illustration
  3. Check the installation condition of the ignition coils (A).

    Tightening torque : 9.8 - 11,8 N·m

    Engine Electrical System — Ignition System / Spark Plug / Troubleshooting illustration
  4. Remove the spark plug. (Refer to Spark Plug - "Removal and Installation")
  5. Visually inspect the external spark plugs.

    Spark plug gap [mm (in.)] : 0.8 - 0.9 (0.0314 - 0.0354)

    Symptom Suspected Cause Correction
    Engine Electrical System — Ignition System / Spark Plug / Troubleshooting illustration
    Melting Electrode
    Abnormal Combustion, Overheat Replace the Spark Plug
    Engine Electrical System — Ignition System / Spark Plug / Troubleshooting illustration
    Carbon and Foreign Matter
    Engine Electrical System — Ignition System / Spark Plug / Troubleshooting illustration
    Ring Crack
    Abnormal Combustion, External Shock
    Engine Electrical System — Ignition System / Spark Plug / Troubleshooting illustration
    Vertical Crack
    External Shock
    Engine Electrical System — Ignition System / Spark Plug / Troubleshooting illustration
    Overheat
    Abnormal Combustion

    Symptom Suspected Cause Correction
    Engine Electrical System — Ignition System / Spark Plug / Troubleshooting illustration
    Poor Gap
    Physical Damage Replace the Spark Plug
    Engine Electrical System — Ignition System / Spark Plug / Troubleshooting illustration
    Flash Over
    Excessive Electrode Wear Replace the Spark Plug, Ignition Coil
    Engine Electrical System — Ignition System / Spark Plug / Troubleshooting illustration
    Corrosion/Rust
    Remaining Oil Mist Reassemble the Spark Plug
  6. Check the resistance between the spark plugs terminal (A) and probe (B) by using a multi-tester or a resistance meter.

    Specified value : 2 - 20 kΩ

    Engine Electrical System — Ignition System / Spark Plug / Troubleshooting illustration
    Note
    • Avoid the contact resistance between probe and spark plugs (when it occurs, the measured value is not stabilized).
    • Be careful not to damage center electrode (A) while measuring resistance.
      Engine Electrical System — Ignition System / Spark Plug / Troubleshooting illustration
  7. Test for changing position of each ignition coil and spark plug.
    1. Remove the spark plug (A) and ignition coil (B) from the misfiring cylinder and exchange them with one of the other cylinders. (Refer to Spark Plug - "Removal and Installation")
      Engine Electrical System — Ignition System / Spark Plug / Troubleshooting illustration
    2. Replace the spark plugs, if misfire moves along the spark plugs.

Spark Plug Removal and Installation

Removal

  1. Remove the ignition coil. (Refer to Ignition System - "Ignition Coil")
  2. Remove the spark plug (A) by using a spark plug socket.

    Tightening torque : 14.7 - 24 N·m

    Engine Electrical System — Ignition System / Spark Plug / Removal and Installation / Removal illustration
    Note
    Be careful not to get foreign matter into the spark plug hole.

Installation

  1. Install in reverse order of removal.
Note
  • Install the spark plug to the specified torque.
  • Be careful not to damage the electrode when installing the spark plug.
  • If the spark plug is dropped, it may cause internal damage. (Do not reuse)
  • When installing the parts, use cloth to clean the contaminated area (A). - Use a clean and soft cloth to avoid damage. (When replacing ignition coil and spark plug together, cleaning is not required.)
    Engine Electrical System — Ignition System / Spark Plug / Removal and Installation / Installation illustration
    Engine Electrical System — Ignition System / Spark Plug / Removal and Installation / Installation illustration

Spark Plug Cleaning

Cleaning

Incomplete combustion builds up carbon deposits and fuel accumulates in the spark plug. Therefore combustion becomes temporarily unstable, and cleaning should be performed as below.

[1st Method]

  1. Start the engine and keep the engine running at idle for 2 minutes.
  2. Place the shift lever in N and press the accelerator to maintain engine rpm at 4,500. Warm up the engine until engine coolant temperature reaches at 80 °C.
  3. Keep the engine running at 2,500 - 3,000 rpm in the N position for 15 minutes.
    Engine Electrical System — Ignition System / Spark Plug / Cleaning illustration

[2nd Method]

Note
If [Method 1] does not work properly, perform the cleaning with [Method 2].
  1. Start the engine and keep the engine running at idle for 2 minutes.
  2. Drive the vehicle for over 20 minutes and keep the engine speed above 3,500 rpm.
    Engine Electrical System — Ignition System / Spark Plug / Cleaning illustration