Restraint

6steps
~36min
2/5difficulty
Done 0 of 6

Contents:

Single-Use Parts

Single-Use Parts

Non-reusable parts (Single-Use Parts) Workshop manual provides “Components and Components Location” which can be used to identify “Non-reusable parts”. When repairing a vehicle, Non-reusable parts such as fasteners, gaskets, washers, clips and garnishes must be replaced. Kia Non-reusable parts are designed to be installed only once. Before working on a vehicle, check “Components and Components Location” to find the non-reusable parts in a system. ※ Symbol of Non-reusable parts
Symbol Meaning
Restraint — Single-Use Parts illustration
Do not reuse the part. Replace with a new one.

※ Example of “Components and Components Location”
Restraint — Single-Use Parts illustration

Specification ➤

Special Service Tools

Special Service Tool

Tool Name / Number Illustration Description
Airbag deployment tool
0957A - 34100A
Restraint — Special Service Tools / Special Service Tool illustration
Used when deploying the airbag
Deployment adapter
0K57A - 3U100A
Restraint — Special Service Tools / Special Service Tool illustration
Used when deploying DAB, PAB, CAB modules and BPT
Used with 0957A - 34100A
Deployment adapter
0957A - 2W100
Restraint — Special Service Tools / Special Service Tool illustration
Used when deploying the SAB module
Used with 0957A - 34100A
Dummy
0957A - 38200
Restraint — Special Service Tools / Special Service Tool illustration
Used to check the airbag module
Dummy adapter
0957A - 2W200
Restraint — Special Service Tools / Special Service Tool illustration
Used to check the resistance of SAB module
Used with 0957A - 38200
Dummy adapter
0957A - 2G000
Restraint — Special Service Tools / Special Service Tool illustration
Used to check resistance of DAB, PAB, CAB modules and BPT
Used with 0957A - 38200

DAB : Driver Airbag PAB : Passenger Airbag SAB : Side Airbag CAB : Curtain Airbag BPT : Seat Belt Pretensioner KAB : Knee Airbag

General Safety Information and Caution ➤

Description and Operation

Description

The airbag system is a supplemental restraint system (SRS) to protect the driver and passengers from injuries by operating the airbags and seat belt pretensioner (BPT) installed on the driver's and front passenger's seats in the event of a vehicle collision. The SRS airbags includes Driver Airbag (DAB) module, driver Knee Airbag (KAB) module, front Passenger's Airbag (PAB) module, driver's and front passenger's seat Belt Pretensioner (BPT), anchor pretensioner, and Side Airbag (SAB) module located on the left and right of driver's and front passenger's seat, and a Curtain Airbag (CAB) module. The SRS control module that controls the SRS airbags, is located at the bottom of the floor console. The SRS airbags consist of a clock spring located on the steering column, a Front Impact Sensor (FIS) that detects a front impact, a Side Impact Sensor (SIS) that detects a side impact, an airbag warning lamp located on the instrument panel and the airbag system wiring.

Airbag warning lamp

The airbag system control module turns on the airbag warning lamp by detecting whether there is an abnormality in the airbag system when the power is applied.
  1. When the airbag system is normal.
    • When the airbag system is normal, the airbag warning lamp turns on for 3 to 6 seconds and turns off.
    Restraint — Description and Operation / Airbag warning lamp illustration
  2. If there is any problem with the airbag system.
    • If there is a problem with the airbag system, the lamp will be on for 6 seconds, then go off for 1 second, then come back on and stay on.
    Restraint — Description and Operation / Airbag warning lamp illustration
  3. When in the variant coding (EOL) mode.
    • When IG is ON, the airbag warning lamp blinks at 1 second intervals until the variant coding (EOL) is normally completed.
    • When variant coding (EOL) is normally completed, the airbag warning lamp turns on for 6 seconds and then turns off.
    • When variant coding (EOL) is not normally completed, the airbag warning lamp continues to blink at 1 second intervals.
    1. When variant coding (EOL) is normally completed.
      Restraint — Description and Operation / Airbag warning lamp illustration
    2. When variant coding (EOL) is not normally completed.
      Restraint — Description and Operation / Airbag warning lamp illustration
If there is a failure of the airbag system or an internal failure of the airbag system control module, variant coding (EOL) should be re-performed after confirming the cause of failure and completing the action using a diagnostic device (KDS). In the following cases, the airbag warning lamp continues to illuminate.
  • If there is a failure of the airbag system or an internal failure of the SRSCM.
  • If there is a Diagnostic Trouble Code (DTC).
  • While communicating with SRSCM by using a diagnostic device (KDS).
If a failure occurs in which the airbag system control module cannot operate, the operation of the airbag warning light cannot be controlled normally. In this case, the airbag warning light operates normally through a circuit that operates independently of the airbag system control module. These cases are:
  • Loss of battery power in the airbag system control module: Airbag warning lamp stays on.
  • Loss of internal operating voltage: Airbag warning lamp stays on.
  • Loss of airbag system control module operation: Airbag warning lamp stays on
  • SRSCM not connected

Repair Procedures

Replacement of components after deploying the SRS

Note
  • Before starting the work related to the airbag, check the diagnosis trouble code (DTC) by using the (KDS), and perform the related work by using the diagnosis trouble code (DTC) list.
  • Be sure to keep the torque specifications presented in shop manuals. Otherwise, it could lead to the malfunction of airbag system.
  1. When the front airbag(s) deployed after collision, replace the following components.
    1. SRS Control Module (SRSCM)
    2. Deployed airbag(s)
    3. Front Impact Sensor
    4. SRS wiring harness
    5. When the driver airbag (DAB) module is deployed, damage to the clock spring is checked and replaced if there is an abnormality.
  2. When the Side Airbag (SAB)/Curtain Airbag (CAB) module is deployed after a crash, replace the following components.
    1. SRS Control Module (SRSCM)
    2. Deployed airbag(s)
    3. Side impact sensor(s) on the deployed side(s)
    4. SRS wiring harness
  3. After repairing the vehicle, check if the SRS operates normally.
    1. Turn IG ON. The airbag warning lamp should turns off after turning on for 3 - 6 seconds.

SRSCM ➤

Airbag Module ➤

Seat Belt System ➤