Intelligent Variable Transmission (IVT) System

~5min read

Contents:

Single-Use Parts

Single-Use Parts

Non-reusable parts (Single-Use Parts) Workshop manual provides “Components and Components Location” which can be used to identify “Non-reusable parts”. When repairing a vehicle, Non-reusable parts such as fasteners, gaskets, washers, clips and garnishes must be replaced. Kia Non-reusable parts are designed to be installed only once. Before working on a vehicle, check “Components and Components Location” to find the non-reusable parts in a system. ※ Symbol of Non-reusable parts
Symbol Meaning
Intelligent Variable Transmission (IVT) System — Single-Use Parts illustration
Do not reuse the part. Replace with a new one.

※ Example of “Components and Components Location”
Intelligent Variable Transmission (IVT) System — Single-Use Parts illustration

Specification ➤

Special Service Tools

Special Service Tool

Tool Name / Number Illustration Description
Engine support fixture (bar)
09200 - 3N000
Intelligent Variable Transmission (IVT) System — Special Service Tools / Special Service Tool illustration
Used for holding engine assembly when removing / installing IVT transmission
※Refer to the engine support fixture assembly drawing below
Engine support fixture (supporter)
09200 - 2S000
09200 - 2S200
Intelligent Variable Transmission (IVT) System — Special Service Tools / Special Service Tool illustration
Used for holding engine assembly when removing / installing IVT transmission
(09200- 2S100 is unnecessary)
※Refer to the engine support fixture assembly drawing below
Engine support fixture (front supporter)
09200 - C3610
Intelligent Variable Transmission (IVT) System — Special Service Tools / Special Service Tool illustration
Used for holding engine assembly when removing / installing IVT transmission
※Refer to the engine support fixture assembly drawing below
Engine support fixture (adapter)
09200 - 4X000
Intelligent Variable Transmission (IVT) System — Special Service Tools / Special Service Tool illustration
Used for holding engine assembly when removing / installing IVT transmission
※Refer to the engine support fixture assembly drawing below
Oil seal installer
09452 - 26100
Intelligent Variable Transmission (IVT) System — Special Service Tools / Special Service Tool illustration
Used for IVT transmission case and housing oil seal installation [2WD]
(Used with the handle)
Oil seal installer
09453 - 3L241
Intelligent Variable Transmission (IVT) System — Special Service Tools / Special Service Tool illustration
Used for IVT transmission case oil seal installation [4WD]
(Used with the handle)
Oil seal installer
09453 - 2W100
Intelligent Variable Transmission (IVT) System — Special Service Tools / Special Service Tool illustration
Used for IVT transmission housing oil seal installation [4WD]
(Used with the handle)
Handle
09231 - H1100
Intelligent Variable Transmission (IVT) System — Special Service Tools / Special Service Tool illustration
Used with the oil seal installer
Position switch guide pin
09480 - A3800
Intelligent Variable Transmission (IVT) System — Special Service Tools / Special Service Tool illustration
Used for fixing N range when installing position switch

※ Engine support fixture assembly drawing
Intelligent Variable Transmission (IVT) System — Special Service Tools / Special Service Tool illustration

Troubleshooting

Troubleshooting

Limp Home Mode

Limp Home Mode features a fail-safe function that prevents dangerous situations in the event of a transmission failure. The vehicle will be driven in limp home mode if the IVT transmission malfunctions. In this mode, the transmission operates at a minimal functionality level (fixed shifting, limited shifting, reverse, neutral), making it possible for the vehicle to reach a service center.
Information
  • Fail safe function : Prevents dangerous situations from developing in the event of a malfunction
  • Limp home function : Maintains minimal functionality (Drive, Reverse, and Neutral) in the event of a malfunction, making it possible for the vehicle to reach a service center

Warning lamp ON

Condition Suspected Cause Remedy
Vehicle Stopped Electric parts fault
(Speed sensor, Solenoid valve, Position switch, E-Module, etc)
Replace the electric parts

Malfunction when changed condition from stop (Including defective engine start)

Condition Suspected Cause Remedy
Vehicle Stopped Position switch fault Inspect the position switch and connector

Unable to drive/reverse

Condition Suspected Cause Remedy
Vehicle Stopped 1. Check driven pulley pressure sensor at static condition using the KDS
: 0 bar / Check Oil pump seizure (shaft sticking)
2. P0731 / P0730 / P0867 warning lamp ON
3. Broken pulley chain belt
4. Damaged gear/clutch/brake
Replace the IVT

Unable to P range released

Condition Suspected Cause Remedy
Vehicle Stopped Parking system (sprag fault sticking) Replace the IVT

Delay / jerk (When the damper is engaged)

Condition Suspected Cause Remedy
Driving condition 1. Damper clutch control solenoid valve fault
2. Valve body fault
3. Broken pulley chain belt
4. Damaged gear/clutch/brake
1. Replace the damper clutch control solenoid valve
2. Replace the valve body
3. Inspect/replace sealing
4. Check the oil level

IVT fluid smell inflow

Condition Suspected Cause Remedy
Driving condition 1. Incorrect fluid level
2. Cooling system fault
1. Check the fluid level
2. Inspect the engine cooling system

Fluid suction noise

Condition Suspected Cause Remedy
Driving condition Low fluid level (leakage, incorrect repair) After checking the fluid leakage from the IVT case or the valve body cover, inspect the fluid level.

Shifting gear trouble

Condition Suspected Cause Remedy
Driving condition Drive pulley speed sensor fault Inspect the drive pulley speed sensor and connector
Driven pulley speed sensor fault Inspect the driven pulley speed sensor and connector
Turbine speed sensor fault Inspect the turbine speed sensor and connector (E-module)
Solenoid valve fault Inspect the solenoid valve
CAN communication fault Inspect the CAN communication line and controller (TCM/ECM)
TCM software fault 1. Inspect the TCM and replace it if necessary
2. After replacement, input oil characteristics and perform TCM adaptive value learning
TCM learning not performed Perform the learning procedure again after resetting "AUTO T/A learning value"
E-Module fault Inspect the E-module & connector
Poor hydraulic pressure control Inspect the IVT hydraulic pressure
Poor hydraulic pressure supply Inspect the oil level
Not performed oil characteristics input after replacement of TCM or IVT Input the oil characteristics
Slipping in the IVT, Damaged clutch/brake Replace the IVT
Position switch fault Inspect the position switch and connector

Shifting shock

Condition Suspected Cause Remedy
Driving condition Bad TCM learning value Perform the learning procedure again after resetting "AUTO T/A learning value"
Not performed oil characteristics input after replacement of TCM or IVT Input the oil characteristics
Low fluid level (leakage, incorrect repair) After checking the fluid leakage from the IVT case or the valve body cover, inspect the fluid level.
Incorrect installation of the IVT Tighten the mounting bolts with the specified torque
Damaged gear/clutch/brake Replace the IVT

Abnormal noise from transmission

Condition Suspected Cause Remedy
Driving condition Damaged bearing / parts stuck inside Replace the IVT
Low oil level Inspect the oil level

IVT Control System ➤

Intelligent Variable Transmission (IVT) ➤

Hydraulic System ➤