Engine Electrical System

Starting System

44steps
~264min
4/5difficulty
02040608010063.747N·mlb·ft
Tightening torque found on this page
Done 0 of 44

Contents:

Troubleshooting

Troubleshooting

No crank
Suspected causes Correction
Low battery charging voltage Battery charging or replace battery
Defective connection, corroded or worn battery terminal Inspect battery terminal or replace cable
Broken fuse Replace fuse
Defective starter Replace starter
Defective body and transaxle ground cable connection condition or disconnected Connect or repair ground cable
Defective battery positive ( + ) cable connection condition or disconnected Inspect battery positive ( + ) cable connection condition and repair or replace it
Discharged battery Replace the battery according to condition after battery charge.

Engine cranks slowly
Suspected causes Correction
Low battery charging voltage Battery charging or replace battery
Defective connection, corroded or worn battery terminal Inspect battery terminal or replace cable
Defective starter Replace starter

Starter keeps running
Suspected causes Correction
Defective starter Replace starter

Starter running but won't engaging
Suspected causes Correction
Wiring short circuit Repair or replace the wiring after inspect wiring connection condition
Broken or worn pinion gear teeth or defective starter Replace starter
Broken ring gear teeth Replace drive plate and torque converter

Turn off the IG while driving
Suspected causes Correction
The alternator fuse wiring is disconnection so the battery is completely discharged Replace alternator main fuse
Inspect battery condition and repair
Defective connection of alternator connector Inspect the connector connection

Bad restart after the engine is turned off
Suspected causes Correction
Deterioration occurs due to poor positive ( + ) terminal contact Replace battery wiring or Tighten at a specified torque

Engine cannot start even during the jump start
Suspected causes Correction
Excessive parasitic current occurs irregularly due to an error in smart key registration.
(Other electronic components and charging-related parts are normal.)
Reregister smart key
Defective wiring Inspect or replace wiring
Discharged battery Inspect or replace battery

On Vehicle Inspection

On Vehicle Inspection

Information
Perform the inspection procedure below.
Engine Electrical System — Starting System / On Vehicle Inspection illustration
  1. Check the starting system by cranking in the P position.
  2. Check the starting system by cranking after inspecting the starter relay. (Refer to Starting System - "Starter Relay")
  3. Check the starting system by cranking after inspecting the battery condition. (Refer to Charging System - "Battery")
    Note
    Check List
    • Battery terminal connection condition
    • Connection condition between the battery negative ( - ) cable and the body
  4. Inspect the starter. (Refer to Starting System - "Starter")
  5. Inspect the starting system components and the wiring.
    Note
    Check List
    • Connector and the wiring between the internal fuse box and the start/stop button
    • Connector and the wiring between the internal fuse box and the starter
    • Engine ground cable connection condition
    • Start/stop button
    • Stop lamp switch

Starter Specification

Specification

Item Specification
Rated voltage (V, kW) 12, 1.2
The number of pinion teeth 13
Performance (No-load, 11 V) Ampere (A) Maximum 70
Speed (rpm) Minimum 2,400

Starter Components and Components Location

Component Location

Engine Electrical System — Starting System / Starter / Components and Components Location / Component Location illustration
1. Starter
1-a. 49.0 - 64 N·m

Starter Description and Operation

Description

  • Starter consist of solenoid, brush holder, armature assembly, reduction pinion gear etc.
  • When the turn on the START, the current flows and is applied to the starter solenoid coil.
  • When supplying the current, engine is cranking after the solenoid plunger and shift lever are moved, and the reduction pinion gear inter lock to the ring gear.
  • To prevent damage from excessive rotation of the armature when starting, the pinion gear clutch overruns.
Engine Electrical System — Starting System / Starter / Description and Operation / Description illustration

Starter Removal and Installation

Removal

  1. Disconnect the battery negative ( - ) terminal.
  2. Remove the engine compartment under cover. (Refer to Engine Mechanical System - "Engine Room Under Cover")
  3. Disconnect the starter connector (A).
    Engine Electrical System — Starting System / Starter / Removal and Installation / Removal illustration
  4. Disconnect the Oil Pressure Sensor (OPS) connector (A).
    Engine Electrical System — Starting System / Starter / Removal and Installation / Removal illustration
  5. Separate the main wiring (A) after removing the fasteners.
    Engine Electrical System — Starting System / Starter / Removal and Installation / Removal illustration
  6. Remove the starter B+ terminal cable (A) after removing the nut.

    Tightening torque : 9.8 - 11,8 N·m

    Engine Electrical System — Starting System / Starter / Removal and Installation / Removal illustration
  7. Remove the starter (A) after removing the bolts.

    Tightening torque : 49.0 - 64 N·m

    Engine Electrical System — Starting System / Starter / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.
    Note
    • The starter mounting bolts should be tightened to the specified torque after pre-tightening the upper bolt and lower bolt.
    • If the starter is dropped, it may cause internal damage. (Do not reuse)

Starter Disassembly and Reassembly

Disassembly

  1. Separate the solenoid M terminal (A) after removing the nut.

    Tightening torque : 9.8 - 11,8 N·m

    Engine Electrical System — Starting System / Starter / Disassembly and Reassembly / Disassembly illustration
  2. Remove the magnetic switch assembly (A) after removing the screws.
    Engine Electrical System — Starting System / Starter / Disassembly and Reassembly / Disassembly illustration
  3. Remove the york & armature assembly (A) after removing the bolts.
    Engine Electrical System — Starting System / Starter / Disassembly and Reassembly / Disassembly illustration
  4. Separate the lever (A) and stop lever (B).
    Engine Electrical System — Starting System / Starter / Disassembly and Reassembly / Disassembly illustration
  5. Separate the york assembly (A), armature assembly (B) and brush holder & bracket assembly (C).
    Engine Electrical System — Starting System / Starter / Disassembly and Reassembly / Disassembly illustration
  6. Remove the stopper (A) by using the socket (B) and rubber mallet.
    Note
    Be careful not to damage the pinion gear when using a rubber mallet.
    Engine Electrical System — Starting System / Starter / Disassembly and Reassembly / Disassembly illustration
  7. Remove the stop ring (A).
    Engine Electrical System — Starting System / Starter / Disassembly and Reassembly / Disassembly illustration
  8. Remove the stopper (A), overrunning clutch (B) and ring gear (C).
    Engine Electrical System — Starting System / Starter / Disassembly and Reassembly / Disassembly illustration

Reassembly

  1. Reassemble in the reverse order of disassembly.

Starter Inspection

Inspection

Magnetic Switch Inspection
  1. Separate the solenoid M terminal (A) after removing the nut.

    Tightening torque : 9.8 - 11,8 N·m

    Engine Electrical System — Starting System / Starter / Inspection illustration
  2. Connect the 12 V battery between the solenoid terminal and starter body.
    Engine Electrical System — Starting System / Starter / Inspection illustration
    Caution
    To avoid damaging the coil, perform the test within 10 seconds.
  3. Replace the starter when pinion gear does not move outside.
  4. Disconnect the cable from solenoid M terminal.
    Engine Electrical System — Starting System / Starter / Inspection illustration
    Caution
    To avoid damaging the coil, perform the test within 10 seconds.
  5. The hold-in coil is normal if the pinion gear does not move to outside.
  6. Disconnect the cable from starter body.
    Engine Electrical System — Starting System / Starter / Inspection illustration
    Caution
    To avoid damaging the coil, perform the test within 10 seconds.
  7. Replace the starter when pinion gear does not move to inside.
  8. Connect the 12 V battery between the solenoid terminal and starter body.
    Engine Electrical System — Starting System / Starter / Inspection illustration
    Caution
    To avoid damaging the coil, perform the test within 10 seconds.
  9. Replace the starter when starter motor does not operate.
  10. Place the starter motor in a vise equipped with soft jaws and connect a fully-charged 12 V battery to starter as follows.
  11. Connect a test ammeter (100 A) and rheostat shown as the illustration.
  12. Connect a voltmeter (15 V) across starter.
    Engine Electrical System — Starting System / Starter / Inspection illustration
  13. Rotate rheostat to the OFF position.
  14. Connect the battery cable from the battery negative ( - ) terminal to the starter.
  15. Adjust so that the battery voltage indicated by the voltmeter is 11 V.
  16. Confirm that the maximum amperage is within the specifications and the starter motor turns smoothly and freely.

    Ampere (A) : Maximum 70 Speed (rpm) : Minimum 2,400

Starter Motor Operation Inspection Free Running Inspection

Starter Cleaning

Cleaning

  1. Do not immerse the yoke assembly or armature assembly in solvents as it may cause the damage in the insulation. Use a cloth to clean the parts.
  2. Do not clean or immerse the reduction pinion gear with a solvent as it is lubricated.
  3. All parts except the operating parts can be cleaned with a brush moistened with solvent and then wipe them with dried cloth.

Starter Relay Repair Procedures

Inspection

  1. Disconnect the battery negative ( - ) terminal.
  2. Remove the starter relay (A) after opening the engine room fuse box cover.
    Engine Electrical System — Starting System / Starter Relay / Repair Procedures / Inspection illustration
  3. Check for continuity between the terminals (30 and 87) using an ohmmeter.
    Terminal Resistance Measure
    30 - 87 1 MΩ or higher If there is continuity between the terminals, replace the relay.

    Engine Electrical System — Starting System / Starter Relay / Repair Procedures / Inspection illustration
  4. Apply 12 V to the terminal 85 and ground to the terminal 86 and then check for continuity between the terminals (30 and 87).
    Terminal Resistance Measure
    30 - 87 1 Ω or less (About 0 Ω) If there is no continuity between the terminals, replace the relay.

    Engine Electrical System — Starting System / Starter Relay / Repair Procedures / Inspection illustration
  5. Install in reverse order of removal.