Single-Use Parts

~3min read

Contents:

Single-Use Parts

Single-Use Parts

Non-reusable parts (Single-Use Parts) Workshop manual provides “Components and Components Location” which can be used to identify “Non-reusable parts”. When repairing a vehicle, Non-reusable parts such as fasteners, gaskets, washers, clips and garnishes must be replaced. Kia Non-reusable parts are designed to be installed only once. Before working on a vehicle, check “Components and Components Location” to find the non-reusable parts in a system. ※ Symbol of Non-reusable parts
Symbol Meaning
Driveshaft and Axle — Single-Use Parts illustration
Do not reuse the part. Replace with a new one.

※ Example of “Components and Components Location”
Driveshaft and Axle — Single-Use Parts illustration

Specification ➤

Special Service Tools

Special Service Tool

Tool Name / Number Illustration Description
Lower arm ball joint remover
0K545 - A9100
Driveshaft and Axle — Special Service Tools / Special Service Tool illustration
Used for removal of front lower arm ball joint
Ball joint puller
09568 - 1S100
Driveshaft and Axle — Special Service Tools / Special Service Tool illustration
Used for removal of tie rod end
CV joint puller
09517 - 4E000
Driveshaft and Axle — Special Service Tools / Special Service Tool illustration
Used for removal of CV joint
Band installer
0K495 - 2W000
Driveshaft and Axle — Special Service Tools / Special Service Tool illustration
Used for installing hook type boot band (low profile) (Sharing handle with 0K495 - C5000)
Band installer
0K495 - C5000
Driveshaft and Axle — Special Service Tools / Special Service Tool illustration
Used for installing ear type boot band (Sharing handle with 0K495 - 2W000)
Sliding hammer
09526 - 11100
Driveshaft and Axle — Special Service Tools / Special Service Tool illustration
Used for removal of CV joint
(Used with 0K495 - C5200)
Adaptor
0K495 - C5200
Driveshaft and Axle — Special Service Tools / Special Service Tool illustration
Used for removal of CV joint
(Used with 09526 - 11100)

Troubleshooting

Troubleshooting

Symptom Suspected causes Repair
Vehicle pulls to one side Front suspension fault or defect Wheel alignment adjust or replace
Steering system fault or defect
Note
Before inspecting or replacing the MDPS, perform the wheel alignment and the steering angle sensor zero-point calibration first.
Wheel alignment adjustment or steering angle sensor zero-point calibration, MDPS inspection or replace
Poor installation of the brake disc and brake pad Replace
Seized wheel bearing Replace
Incorrect tire air pressure Adjustment
Unbalanced wear of tires Adjust the wheel alignment or replace the tire
Incorrect wheel balance Adjust or replace
Abnormal wheel alignment Adjustment
Vibration Over abrasion, separation, damaged or bended on driveshaft Replace
(Replacement using repair kit)
Wheel bearing excessive play Replace
Shimmy Incorrect wheel balance Adjust or replace
Defect on front suspension and steering gear Adjust or replace
Noise Excessive wear, damaged, or bent driveshaft Replace
(Replacement using repair kit)
Noise on connecting part of driveshaft and hub while driving straight, back or curve (Clicking or Creaking noise) Tighten hub nuts
or inner washer replacement
Noise from inner side of shaft while driving curve (Repeated tapping noise) Replace
(Replacement using repair kit)
Friction noise on driveshaft boots (Sticky noise) Clean and apply fluorine lubricant
Loose hub nut Tighten or replace
Defect on front suspension and steering gear Adjust or replace
Loose disc screw Adjustment
Noise on wheel bearing while driving (Whir noise) Replace
Wheel bearing has excessive play, contacted surface of flange burnt Replace
Leakage Leakage of grease on driveshaft boots (partial parts replacement when inboard side boots has leakage) Replace
(Replacement using repair kit)
Rust Corrosion on nonpainting area (Not a problem for functioning) Explain to the customer it is normal
ABS warning lamp illuminated Loose wheel bearing sensor and sensor cable Adjustment
Contaminated wheel bearing sensor connector Cleaning
Communication error (Diagnosis using KDS) Adjustment

Front Axle Assembly ➤

Rear Axle Assembly ➤

Driveshaft Assembly ➤