Single-Use Parts

18steps
~108min
4/5difficulty
0102030405012.79N·mlb·ft
Tightening torque found on this page
Done 0 of 18

Contents:

Single-Use Parts

Single-Use Parts

Non-reusable parts (Single-Use Parts) Workshop manual provides “Components and Components Location” which can be used to identify “Non-reusable parts”. When repairing a vehicle, Non-reusable parts such as fasteners, gaskets, washers, clips and garnishes must be replaced. Kia Non-reusable parts are designed to be installed only once. Before working on a vehicle, check “Components and Components Location” to find the non-reusable parts in a system. ※ Symbol of Non-reusable parts
Symbol Meaning
Brake System — Single-Use Parts illustration
Do not reuse the part. Replace with a new one.

※ Example of “Components and Components Location”
Brake System — Single-Use Parts illustration

Specification ➤

Special Service Tools

Special Service Tool

Tool Name / Number Illustration Description
Piston expander
09581 - 11000
Brake System — Special Service Tools / Special Service Tool illustration
Spreading the front brake caliper piston.
Sensor cap installer
09527 - AL300
Brake System — Special Service Tools / Special Service Tool illustration
Used for installing wheel speed sensor cap (for outer diameter : 67.2 mm, 2.64 in.)

Troubleshooting

Troubleshooting

  1. The brake system can be diagnosed quickly using the KDS (Refer to "DTC Diagnostic Guide").
    1. Self diagnosis : Checking failure and code number (DTC)
    2. Sensor data : Checking the system input/output data state
    3. Forced operation : Check the system operating condition
    4. Additional function : Controlling other features including system option setting and zero point adjustment
The table below shows the most common defects and repair remedies in the brake system. each number indicates the priority of the likely cause of the defects.

Brake warning lamp illuminates

Suspected causes Correction
1. Brake fluid level sensor (not connected securely) Reconnect or replace
2. Low brake fluid level Fill and leak check
Parking brake (Set) Release

Lower pedal or sponge pedal

Suspected causes Correction
1. Brake system (oil leakage) Repair
2. Brake system (air inflow) Perform air bleeding procedure
3. Piston seal (Wear or damage) Replacement
4. Master cylinder (malfunction) Replacement

Brake drag

Suspected causes Correction
1. Brake pedal free separation (minimum) Adjustment
2. Pad (Crack or bent) Replacement
3. Piston (stuck) Replacement
4. Piston (frozen) Replacement
5. Anchor or return spring (malfunction) Replacement
6. Booster system (leakage of vacuum) Replacement
7. Master cylinder (malfunction) Replacement

Uneven brake

Suspected causes Correction
1. Piston (stuck) Replacement
2. Pad (Polluted) Replacement
3. Piston (frozen) Replacement
4. Disc (scratches) Replacement
5. Pad (Crack or bent) Replacement

Heavy pedal and brake trouble

Suspected causes Correction
1. Brake system (oil leakage) Repair
2. Brake system (air inflow) Perform air bleeding procedure
3. Pad (wear) Replacement
4. Pad (Crack or bent) Replacement
5. Pad (Polluted) Replacement
6. Pad (Slippery) Replacement
7. Disc (Dent or scratch) Replacement
8. Booster system (leakage of vacuum) Replacement

Brake Noise

Suspected causes Correction
1. Pad (Crack or bent) Replacement
2. Mounting bolt (Got loose) Retighten
3. Disc (Dent or scratch) Replacement
4. Sliding pin (Wear) Replacement
5. Pad (dirty) Cleaning
6. Pad (Slippery) Replacement
7. Anchor or Return spring (Faulty) Replacement
8. Brake pad shim (damaged) Replacement

Poor Braking Performance (at High Speed)

Suspected causes Correction
1. Pad (Wear) Replacement
2. Master cylinder (Damaged) Replacement

Abnormal vibration when braking.

Suspected causes Correction
1. Booster system (leakage of vacuum) Replacement
2. Excessive free play of the brake pedal Adjustment
3. Master cylinder (Damaged) Replacement
4. Brake caliper Replacement
5. Master cylinder cap seal Replacement
6. Damaged brake line Replacement
7. Disc juddering Perform brake judder inspection and resurface or replace the disc

Brake Bleeding Procedures

Brake System Bleeding Procedures

Information
This work is to be performed by two people.
  • Main worker : Bleeds the system by manually opening and closing the bleed screw and detecting air coming out of brake lines.
  • Assistant : Brake pedal operation and scanner operation inside the vehicle.
  • Working order : Brake System — Brake Bleeding Procedures / Brake System Bleeding Procedures illustration Front RH → Brake System — Brake Bleeding Procedures / Brake System Bleeding Procedures illustration Rear LH → Brake System — Brake Bleeding Procedures / Brake System Bleeding Procedures illustration Front LH → Brake System — Brake Bleeding Procedures / Brake System Bleeding Procedures illustration Rear RH
Note
  • Do not reuse the drained brake fluid.
  • Always use genuine DOT4 brake Fluid, Using a non-genuine DOT4 brake fluid can cause corrosion and decrease the life of the system.
  • Make sure that no dirt or other foreign matter is allowed to contaminate the brake fluid.
  • Be careful not to get brake fluid on the body or vehicle and, if so, wipe immediately with a clean cloth.
  • Before air bleeding, check all the brake lines for leakage.
  • Check the installation of ABS and ESC control unit.
Air Bleeding Procedure (Step 1)
  1. Remove the front and rear wheels and tires.
  2. Fill the brake fluid to the "MAX" line.
    Note
    Install a tool that can continuously supply brake fluid to the master cylinder reservoir, or supply brake fluid so that the reservoir is always full during operation.
    Brake System — Brake Bleeding Procedures / Brake System Bleeding Procedures illustration
    Air Bleeding Sequence and 1st, 2nd, and 3rd Bleeding Procedures (Play ▶)Brake System — Brake Bleeding Procedures / Brake System Bleeding Procedures illustration

    Video: Air Bleeding Sequence and 1st, 2nd, and 3rd Bleeding Procedures

    Notes When Refering Video This video provides guidance for understanding complex or hard-to-follow procedures by showing each step clearly. As needed, the video also provides clear guidance on essential procedural steps, including adjustment and diagnostic processes, the use of SSTs, and precautions to avoid component damage.
    • This video is created using common specifications and may differ from the actual vehicle.
    • The location and repair procedures of the parts may vary depending on vehicle model, model year, region, and specifications.
    • Check the KDS guide for detailed information on how to use the KDS.
    • Check the manual for detailed maintenance procedures.
    • Unauthorized reproduction, distribution, or sharing of this video is prohibited.
  3. The main worker connects the clear hose to the wheel bleeder screw (A) and sends a signal to assistant to depress the brake pedal.
  4. The assistant to pump the brake pedal 2 times with normal brake force and then keep the brake pedal depressed.
  5. While the assistant is depressing the brake pedal, remove the bleeder screw (A) momentarily to remove the air, and then fasten it again.

    Tightening torque : 6.9 - 12,7 N·m

    Front
    Brake System — Brake Bleeding Procedures / Brake System Bleeding Procedures illustration
    Rear
    Brake System — Brake Bleeding Procedures / Brake System Bleeding Procedures illustration
    Note
    • Air may enter, so open and close the bleed screw only 1/4 of the way.
    • With the brake pedal pressed, open and close the bleeder screw.
  6. Repeat the above procedure until no air bubbles appear in the brake fluid.
  7. The assistant presses the brake pedal strongly twice and sends a stand-by signal to the main worker with the brake pedal pressed.
  8. While the assistant is depressing the brake pedal, remove the bleeder screw (A) momentarily to remove the air, and then fasten it again.

    Tightening torque : 6.9 - 12,7 N·m

    Front
    Brake System — Brake Bleeding Procedures / Brake System Bleeding Procedures illustration
    Rear
    Brake System — Brake Bleeding Procedures / Brake System Bleeding Procedures illustration
    Note
    • Air may enter, so open and close the bleed screw only 1/4 of the way.
    • With the brake pedal pressed, open and close the bleeder screw.
  9. Repeat the above procedure until no air bubbles appear in the brake fluid.
  10. When air bleeding is completed, fill the reservoir with brake fluid to the 'MAX' line.
    Information
    If all of the conditions below are satisfied, the subsequent steps can be omitted.
    • If the ESC control unit is not replaced
    • If the reservoir tank is not replaced.
    • If the brake tube is not replaced.
    • If no bubbles appear in the brake fluid
  11. Check the brake pedal stroke.

    Pedal Full Stroke [mm, (in.)] : 132 - 138 (5.197 - 5.433)

  12. Check the brake fluid level and replenish brake fluid until the 'MAX' (A) level.
    Note
    Install a tool that can continuously supply brake fluid to the master cylinder reservoir, or supply brake fluid so that the reservoir is always full during operation.
  13. Perform the order below with the KDS. (S/W Management → ABSESC - Brake → HCU Air Bleeding Mode)
    Information
    • Refer to the KDS screen for operating conditions and details..
    • The assistant operates the EPB switch simultaneously with the brake pedal to repeat activation and deactivation.
    • When the EPB is repeatedly activated and deactivated, the worker hits the caliper body with a rubber mallet.
  14. When air bleeding is completed, fill the reservoir with brake fluid to the 'MAX' line.
  15. Check the brake pedal stroke.

    Pedal Full Stroke [mm, (in.)] : 132 - 138 (5.197 - 5.433)

  16. Perform the same operation as the "Air Bleeding Procedure (Step 1)".
  17. Check the brake pedal stroke.

    Pedal Full Stroke [mm, (in.)] : 132 - 138 (5.197 - 5.433)

  18. Install the front and rear wheel and tires.
Air Bleeding Procedure (Step 2) This procedure should be followed to ensure adequate bleeding of air and filling of the ESC unit, brake lines and master cylinder with brake fluid. Air Bleeding Procedure (Step 3)

Brake System ➤

Parking Brake System ➤

ESC (Electronic Stability Control) System ➤