Engine Control / Fuel System

ISG (Idle Stop & Go) System

6steps
~36min
2/5difficulty
0102030405011.89N·mlb·ft
Tightening torque found on this page
Done 0 of 6

Contents:

Description and Operation

Description

  • ISG system improves fuel efficiency and reduces emissions by temporary stop the vehicle engine either at waiting for a traffic signal or stopping.
  • The ISG system is always ON whenever the engine start.
  • If the vehicle is completely stopped while the brake pedal is pressed, the engine will automatically stop and the AUTO STOP indicator (green) ON.
  • If you release your foot from the brake pedal while the engine is automatically stopped, the engine will restart and the AUTO STOP indicator will OFF. During AUTO HOLD operation, the engine remains stopped even if you release the brake pedal. When you press the accelerator pedal, the engine will restart.

System Components

Information
The ISG system consists of a mutual network among the related components. Refer to relevant system manual for detail. (Refer to table below)
Component System
ECM Engine Control / Fuel System - Engine Control Module (ECM)
Seat belt switch Restraint - Seat Belt Buckle Switch (BS)
Door switch Body Electrical System - Keyless Entry And Burglar Alarm
Hood switch Body Electrical System - Keyless Entry And Burglar Alarm
Brake switch Brake System - Brake Switch
Brake booster vacuum pressure sensor Brake System - Brake Booster
Ambient temperature sensor Heating, Ventilation And Air Conditioning - Ambient Temperature Sensor
Battery sensor Engine Electrical System - Battery Sensor
AGM battery Engine Electrical System - Battery
DC DC converter Engine Electrical System - DC DC converter
Starter Engine Electrical System - Starter
Position switch Automatic Transaxle System - Position Switch

  • ECM : Using all vehicle control system information, the ECM controls the Engine ON and OFF.
    Engine Control / Fuel System — ISG (Idle Stop & Go) System / Description and Operation / System Components illustration
  • Seat belt switch : It detects the seat belt engagement and this information is used as the ISG system operating condition.
    Engine Control / Fuel System — ISG (Idle Stop & Go) System / Description and Operation / System Components illustration
  • Door switch : It detects the driver side door open/close status and this information is used as the ISG system operating condition.
    Engine Control / Fuel System — ISG (Idle Stop & Go) System / Description and Operation / System Components illustration
  • Hood switch : It detects the hood open/close status and this information is used as the ISG system operating condition.
    Engine Control / Fuel System — ISG (Idle Stop & Go) System / Description and Operation / System Components illustration
  • Brake switch : It detects the brake pedal operation and this information is used as the ISG system operating condition.
    Engine Control / Fuel System — ISG (Idle Stop & Go) System / Description and Operation / System Components illustration
  • Accelerator position sensor : It detects the accelerator pedal operation and this information is used as the ISG system operating condition.
    Engine Control / Fuel System — ISG (Idle Stop & Go) System / Description and Operation / System Components illustration
  • Position switch : It detects the gear shift position (P/R/N/D, manual mode) and this information is used as the ISG system operating condition.
    Engine Control / Fuel System — ISG (Idle Stop & Go) System / Description and Operation / System Components illustration
  • Brake booster vacuum pressure sensor : It detects the brake pressure and this information is used as the ISG system operating condition.
    Engine Control / Fuel System — ISG (Idle Stop & Go) System / Description and Operation / System Components illustration
  • Ambient temperature sensor : It detects the ambient temperature and this information is used as the ISG system operating condition.
    Engine Control / Fuel System — ISG (Idle Stop & Go) System / Description and Operation / System Components illustration
  • Battery sensor : If the battery sensor is deactivated, the ISG system does not work.
    Engine Control / Fuel System — ISG (Idle Stop & Go) System / Description and Operation / System Components illustration
  • AGM battery : Due to more frequent engine start ON and OFF process than regular vehicles, the vehicles with ISG require the higher battery performance and the better battery state of charge management. Despite the high loads by frequent charging and discharging, AGM battery presents excellent durability.
    Engine Control / Fuel System — ISG (Idle Stop & Go) System / Description and Operation / System Components illustration
  • DC/DC converter : The DC converter supplies the boosted voltage (12 ± 0.5V) to prevent electronic device (AVN or Audio, Cluster, etc.) reset from voltage drop at engine automatic start.
    Engine Control / Fuel System — ISG (Idle Stop & Go) System / Description and Operation / System Components illustration
  • Starter : Vehicles with ISG are frequently engine ON/OFF, therefore starter motor with improved durability is applied.
    Engine Control / Fuel System — ISG (Idle Stop & Go) System / Description and Operation / System Components illustration
  • ISG OFF switch : The ISG system is always ON whenever the engine starts, and can ISG system OFF by pressing the switch.
    Engine Control / Fuel System — ISG (Idle Stop & Go) System / Description and Operation / System Components illustration

System Operating Condition

Division Item Condition
Auto start & Auto stop Driver condition ISG OFF switch OFF
Switch (Seat belt/Door/Hood) Fastened/Closed/Closed
Gear position D/N
Pedal condition (Brake/Clutch) Brake condition
ON (Auto stop) / OFF (Auto start)
Vehicle speed Entering 0 kph after driving over 5 kph (3,1 mph).
Climate control system condition FATC/MTC Satisfied
MPDS Less than 180 degrees
Battery condition Charge/Discharge performance SOC > 68 %
Engine coolant temperature 20 - 43 °C
Ambient air temperature Ambient air temperature : -20 to 50 °C
Atmospheric pressure More than 750 hPa (75 kph, 0.76 kg/cm², 10.88 psi)
Brake vacuum pressure Less than -35 kpa (-0.36 kg/cm², -5.07 psi)
Incline condition -5 to 12%
ECU, TCU condition Condition (temperature, error, OBD diagnosis) satisfied
ISG related error None
Forced restart Climate control system condition Blower MAX. / Front Defogger ON
Battery condition Voltage Insufficient charging and discharging performance
Safety Brake vacuum pressure More than -35 kpa (-0.36 kg/cm², -5.07 psi)
Vehicle speed More than 1.5 kph (0,9 mph)
Switch Seat belt/Door Open during brake pedal ON
Hood open Start by using the key
(Message appear on instrument cluster)
Brake/Accel pedal ON at the same time Immediately restart
ISG OFF switch Immediately restart

Inspection

Inspection

Information
  • The ISG related sensors or system error occurs, the yellow AUTO STOP indicator on the cluster will stay on after blinking for 5 seconds and light on the ISG OFF button will illuminate.
  • The ISG system may not work under following conditions.
  • The battery is weak
  • The brake vacuum pressure is too low
  • The battery sensor is deactivated
  • The ISG system consists of a mutual network among the related components. Refer to the relevant system manual for detailed repair procedures. (Refer to table below)
Component System
ECM Engine Control / Fuel System - Engine Control Module (ECM)
Seat belt switch Restraint - Seat Belt Buckle Switch (BS)
Door switch Body Electrical System - Keyless Entry And Burglar Alarm
Hood switch Body Electrical System - Keyless Entry And Burglar Alarm
Brake switch Brake System - Brake Switch
Brake booster vacuum pressure sensor Brake System - Brake Booster
Ambient temperature sensor Heating, Ventilation And Air Conditioning - Ambient Temperature Sensor
Battery sensor Engine Electrical System - Battery Sensor
AGM battery Engine Electrical System - Battery
DC DC converter Engine Electrical System - DC DC converter
Starter Engine Electrical System - Starter
position switch Automatic Transaxle System - Inhibitor Switch

ISG OFF switch Removal and Installation

Removal

  1. Remove the side crash pad switch. (Refer to Body Electrical System - "Headlamp Leveling Switch")

Installation

  1. Install in the reverse order of removal.

ISG OFF switch Inspection

Inspection

  1. Remove the side crash pad switch.
  2. After pushing the ISG OFF switch, check for continuity between the ground (pin 8) and signal (pin 2).
    Engine Control / Fuel System — ISG (Idle Stop & Go) System / ISG OFF switch / Inspection illustration

DC/DC Converter Specifications

Specification

[200W]
Item Specification
Input voltage range (V) 7 - 16
Battery power supply (B+) output voltage (V) 11.4 - 12.6
ACC output voltage (V) 11 - 13

DC/DC Converter Description and Operation

Description

Due to the considerably more frequent occurrence of starting operations, the electrical load that occurs often leads to voltage dips in the vehicle network. In order to stabilize the power supply for certain voltage-sensitive electrical components, a DC/DC converter is used in conjunction with the ISG function. The DC/DC converter supplies the relay with a voltage that also remains constant during the starting operation. The DC/DC converter is fitted at the behind of the glove box. Via the test leads for input voltage and the start relay , the electronics decide whether the power is supplied to the output via the bypass or the DC/DC converter. In the bypass mode, the on-board supply voltage is not fed across the DC/DC converter, rather is transferred directly to the outputs. In the booster phase, the vehicle voltage is adapted.
Engine Control / Fuel System — ISG (Idle Stop & Go) System / DC/DC Converter / Description and Operation / Description illustration

Operation

Engine Control / Fuel System — ISG (Idle Stop & Go) System / DC/DC Converter / Description and Operation / Operation illustration

DC/DC Converter Removal and Installation

Removal

  1. Disconnect the battery negative (-) terminal.
  2. Remove the crash pad lower panel. (Refer to Body "Crash Pad Lower Panel")
  3. Disconnect the DC/DC converter connector (A).
    Engine Control / Fuel System — ISG (Idle Stop & Go) System / DC/DC Converter / Removal and Installation / Removal illustration
  4. Remove the DC/DC converter (A) after removing the nuts.

    Tightening torque : 9.8 - 11,8 N·m

    Engine Control / Fuel System — ISG (Idle Stop & Go) System / DC/DC Converter / Removal and Installation / Removal illustration

Installation

  1. Install in the reverse order of removal.
    Note
    • Install the DC/DC converter with specified torque.
    • If the DC/DC converter is dropped, it may cause internal damage. (Do not reuse)
    • When the negative ( - ) terminal of the battery is disconnected, Idle Stop & Go (ISG) function will be disabled due to the initialization of the battery sensor.
    • To operate ISG function, connect the negative ( - ) terminal and wait for about 4 hours (battery to be stabilized) during IG OFF.