Engine Control / Fuel System

Engine Control System

109steps
~654min
4/5difficulty
0102030405015.712N·mlb·ft
Tightening torque found on this page
Done 0 of 109

Contents:

Description and Operation ➤

Accelerator Position Sensor (APS) Specification

Specification

Accelerator Pedal Position Output voltage (V)
APS1 APS2
Accelerator pedal is not pressed (*E.C.P) 0.7 - 0.8 0.325 - 0.425
Accelerator pedal is fully pressed (*W.O.T) 3.98 - 4.22 1.93 - 2.17

*E.C.P : Electrically Close Position *W.O.T : Wide Open Throttle

Accelerator Position Sensor (APS) Description and Operation

Description

  • Accelerator Position Sensor (APS) is mounted on the accelerator pedal module and is an important sensor that transmits the driver's accelerating action to Engine Control Module (ECM) to determine the amount of fuel injection according to the required acceleration speed.
  • The APS is one of the most important sensors in engine control system, which consists of the two sensors working individually.
  • Each sensor is composed of an independent circuit, Sensor 2 outputs 50% of signal value of Sensor 1 and the APS is determined to be a fault when the proportion of voltage for each sensor is out of certain range.
Engine Control / Fuel System — Engine Control System / Accelerator Position Sensor (APS) / Description and Operation / Description illustration

Accelerator Position Sensor (APS) On Vehicle Inspection

On Vehicle Inspection

  1. The engine control system can be more quickly diagnosed for problems by using the KDS (Refer to "DTC guide").
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) using the KDS (Refer to DTC guide when fault code is found)
    2. Data analysis : Checking the system input/output data state (Data Analysis → System Selection → Engine)
      Accelerator Pedal Position Output voltage (V)
      APS1 APS2
      Accelerator pedal is not pressed (*E.C.P) 0.7 - 0.8 0.325 - 0.425
      Accelerator pedal is fully pressed (*W.O.T) 3.98 - 4.22 1.93 - 2.17

      *E.C.P : Electrically Close Position *W.O.T : Wide Open Throttle
    Information
    Refer to the KDS screen for operating conditions and details

Accelerator Position Sensor (APS) Removal and Installation

Removal

  1. Disconnect the battery negative ( - ) terminal.
  2. Disconnect the accelerator pedal module connector (A).
    Engine Control / Fuel System — Engine Control System / Accelerator Position Sensor (APS) / Removal and Installation / Removal illustration
  3. Remove the accelerator pedal module (A) after removing the nuts.

    Tightening torque : 12.7 - 15,7 N·m

    Engine Control / Fuel System — Engine Control System / Accelerator Position Sensor (APS) / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.
    Note
    • Install the accelerator pedal module to the specified torque.
    • If the accelerator pedal module is dropped, it may cause internal damage. (Do not reuse)

Camshaft Position Sensor (CMPS) Specification

Specification

Item Specification
Operating voltage (V) 4.75 - 5.25
Current consumption (mA) Maximum 10

Camshaft Position Sensor (CMPS) Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Camshaft Position Sensor (CMPS) / Components and Components Location / Component Location illustration
1. Engine Cover
2. Camshaft Position Sensor (CMPS) - Exhaust
2-a. 9.8 - 11,8 N·m
3. Camshaft Position Sensor (CMPS) - Intake
3-a. 9.8 - 11,8 N·m

Camshaft Position Sensor (CMPS) Description and Operation

Description

  • The Camshaft Position Sensor (CMPS) is a hall sensor, which detects the camshaft position by using a hall element.
  • It is synchronized with Crankshaft Position Sensor (CKPS) and detects the piston position of each cylinder which cannot be detected by the CKPS.
  • The two CMPS are installed on engine head cover of bank 1 and 2 (intake, exhaust) respectively and use a target wheel installed on the camshaft.
  • Engine Control Module (ECM) detects the cycle of each cylinder based on the CMPS signal and controls the fuel injection of each cylinder.
Engine Control / Fuel System — Engine Control System / Camshaft Position Sensor (CMPS) / Description and Operation / Description illustration

Camshaft Position Sensor (CMPS) On Vehicle Inspection

On Vehicle Inspection

  1. The engine control system can be more quickly diagnosed for problems by using the KDS (Refer to "DTC guide").
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) using the KDS (Refer to DTC guide when fault code is found)
    2. Actuation test : Checking the Camshaft Position Sensor (CMPS) operation condition (Data Analysis → System Selection → Engine → Actuation test → Oil Control Valve - Intake Bank1 / Oil Control Valve - Exhaust Bank1 (Option))
    Information
    Refer to the KDS screen for operating conditions and details

Component Inspection

  1. Check signal waveform of Camshaft Position Sensor (CMPS) by using a KDS.

    Specified value : Refer to "DTC diagnostic guide"

Camshaft Position Sensor (CMPS) Removal and Installation

Removal

Caution
Wait until cooling the engine to prevent scalding by engine overheating.
Intake
  1. Disconnect the battery negative ( - ) terminal.
  2. Remove the engine cover. (Refer to Engine Mechanical System - "Engine Cover")
  3. Disconnect the Camshaft Position Sensor (CMPS) connector (A).
    Engine Control / Fuel System — Engine Control System / Camshaft Position Sensor (CMPS) / Removal and Installation / Removal illustration
  4. Remove the CMPS (A) after removing the bolt.

    Tightening torque : 9.8 - 11,8 N·m

    Engine Control / Fuel System — Engine Control System / Camshaft Position Sensor (CMPS) / Removal and Installation / Removal illustration
  5. Disconnect the battery negative ( - ) terminal.
  6. Remove the engine cover. (Refer to Engine Mechanical System - "Engine Cover")
  7. Disconnect the Camshaft Position Sensor (CMPS) connector (A).
    Engine Control / Fuel System — Engine Control System / Camshaft Position Sensor (CMPS) / Removal and Installation / Removal illustration
  8. Remove the breather hose (A).
    Engine Control / Fuel System — Engine Control System / Camshaft Position Sensor (CMPS) / Removal and Installation / Removal illustration
  9. Remove the CMPS (A) after removing the bolt.

    Tightening torque : 9.8 - 11,8 N·m

    Engine Control / Fuel System — Engine Control System / Camshaft Position Sensor (CMPS) / Removal and Installation / Removal illustration
Exhaust

Installation

  1. Install in reverse order of removal.
    Note
    • Install the Camshaft Position Sensor (CMPS) to the specified torque.
    • If the CMPS is dropped, it may cause internal damage. (Do not reuse)
    • Apply the engine oil to the O-ring (A).
    Engine Control / Fuel System — Engine Control System / Camshaft Position Sensor (CMPS) / Removal and Installation / Installation illustration
    • Install the CMPS by pushing it into the installation hole firmly. and be careful not to damage the sensor.

Crankshaft Position Sensor (CKPS) Specification

Specification

Item Specification
Operating voltage (V) 4.5 - 5.5
Current consumption (mA) 6.8

Crankshaft Position Sensor (CKPS) Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Crankshaft Position Sensor (CKPS) / Components and Components Location / Component Location illustration
1. Crankshaft Position Sensor (CKPS)
1-a. 9.8 - 11,8 N·m

Crankshaft Position Sensor (CKPS) Description and Operation

Description

  • The Crankshaft Position Sensor (CKPS) is a sensor that detects the engine rotation speed (rpm).
  • The engine rotation speed (rpm) is the most important variable in the electronic control engine, and if the engine rotation speed signal is not input to the Engine Control Module (ECM), the engine may stop due to the CKPS signal not being input.
  • The CKPS determines which stroke the current piston position is on by the target-wheel, and the target-wheel consists of 58 slots and 2 empty slots at 360 degrees of crank angle (CA).
Engine Control / Fuel System — Engine Control System / Crankshaft Position Sensor (CKPS) / Description and Operation / Description illustration

Crankshaft Position Sensor (CKPS) On Vehicle Inspection

On Vehicle Inspection

  1. The engine control system can be more quickly diagnosed for problems by using the KDS (Refer to "DTC guide").
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) using the KDS (Refer to DTC guide when fault code is found)
      Information
      Refer to the KDS screen for operating conditions and details

Component Inspection

  1. Check signal waveform of Crankshaft Position Sensor (CKPS) by using a KDS.

    Specified value : Refer to "DTC diagnostic guide"

Crankshaft Position Sensor (CKPS) Removal and Installation

Removal

  1. Disconnect the battery negative ( - ) terminal.
  2. Remove the engine compartment under cover. (Refer to Engine Mechanical System - "Engine Room Under Cover")
  3. Disconnect the Crankshaft Position Sensor (CKPS) connector (A).
    Engine Control / Fuel System — Engine Control System / Crankshaft Position Sensor (CKPS) / Removal and Installation / Removal illustration
  4. Remove the connector (A) from the bracket (B) by pushing it in the direction of the arrow.
    Engine Control / Fuel System — Engine Control System / Crankshaft Position Sensor (CKPS) / Removal and Installation / Removal illustration
  5. Remove the CKPS (A) and the wiring clip (B) after removing the bolt.

    Tightening torque : 9.8 - 11,8 N·m

    Engine Control / Fuel System — Engine Control System / Crankshaft Position Sensor (CKPS) / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.
    Note
    • Install the Crankshaft Position Sensor (CKPS) to the specified torque.
    • If the CKPS is dropped, it may cause internal damage. (Do not reuse)
    • Apply the engine oil to the O-ring (A).
    Engine Control / Fuel System — Engine Control System / Crankshaft Position Sensor (CKPS) / Removal and Installation / Installation illustration

CVVT Oil Control Valve (OCV) Specification

Specification

Item Specification
Coil resistance (MΩ) Minimum 1 [@500 VAC, 20 °C]

CVVT Oil Control Valve (OCV) Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / CVVT Oil Control Valve (OCV) / Components and Components Location / Component Location illustration
1. Oil Control Valve (OCV) - Intake
1-a.9.8 - 11,8 N·m
2. Oil Control Valve (OCV) - Exhaust
2-a. 9.8 - 11,8 N·m

CVVT Oil Control Valve (OCV) Description and Operation

Description

  • The Continuous Variable Valve Timing (CVVT) system uses Engine Control Module (ECM) control signals that vary with engine RPM and load to advance or retard the timing of opening/closing the intake or exhaust valve.
  • According to the valve overlap and underlap between the intake and exhaust valve by CVVT, there are effects such as reduce the pumping loss, occur internal (Exhaust Gas Recirculation (EGR) and improve the combustion stability and volumetric efficiency. For these reasons, fuel efficiency and engine performance are improved, and the exhaust gas (NOx, HC) decreases.
  • The CVVT Oil Control Valve (OCV) supplies or discharges the oil to a cam phaser by changing the path of engine oil, receiving the PWM (Pulse Width Modulation) signal of ECM.
  • The oil from the OCV changes the phase of the cam shaft by advancing or retarding the cam shaft by rotating the rotor connected to the cam shaft inside the cam phaser.
Engine Control / Fuel System — Engine Control System / CVVT Oil Control Valve (OCV) / Description and Operation / Description illustration

CVVT Oil Control Valve (OCV) On Vehicle Inspection

On Vehicle Inspection

  1. Disconnect the battery negative ( - ) terminal.
  2. Remove the engine cover. (Refer to Engine Mechanical System - "Engine Cover")
  3. Measure the resistance between terminals after disconnecting the Oil Control Valve (OCV) connector (A). Intake
    Engine Control / Fuel System — Engine Control System / CVVT Oil Control Valve (OCV) / On Vehicle Inspection illustration
    Exhaust
    Engine Control / Fuel System — Engine Control System / CVVT Oil Control Valve (OCV) / On Vehicle Inspection illustration
  4. Check that the resistance is within the specification.
    Item Specification
    Coil resistance (MΩ) Minimum 1 [@500 VAC, 20 °C]

CVVT Oil Control Valve (OCV) Removal and Installation

Removal

  1. Disconnect the battery negative ( - ) terminal.
  2. Remove the engine cover. (Refer to Engine Mechanical System - "Engine Cover")
  3. Disconnect the Oil Control Valve (OCV) connector (A). [Intake]
    Engine Control / Fuel System — Engine Control System / CVVT Oil Control Valve (OCV) / Removal and Installation / Removal illustration
    [Exhaust]
    Engine Control / Fuel System — Engine Control System / CVVT Oil Control Valve (OCV) / Removal and Installation / Removal illustration
  4. Remove the OCV (A) after removing the bolt.

    Tightening torque : 9.8 - 11,8 N·m

    [Intake]
    Engine Control / Fuel System — Engine Control System / CVVT Oil Control Valve (OCV) / Removal and Installation / Removal illustration
    [Exhaust]
    Engine Control / Fuel System — Engine Control System / CVVT Oil Control Valve (OCV) / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.
    Note
    • Install the Oil Control Valve (OCV) to the specified torque.
    • If the OCV is dropped, it may cause internal damage. (Do not reuse)
    • Apply the engine oil to the O-ring.

Electronic Throttle Control (ETC) Module Specification

Specification

Item Specification
Motor Type DC Motor
Operating voltage (V) 7.5 - 16
Coil resistance (Ω) 0.3 - 100 [20 °C]
Sensor Supply voltage (V) 5
Sensor output voltage (V) Throttle angle (°) TPS 1 TPS 2
0 0.5 4.5
10 0.96 4.05
20 1.41 3.59
30 1.87 3.14
40 2.32 2.68
50 2.78 2.23
60 3.23 1.77
70 3.69 1.32
80 4.14 0.86
90 4.60 0.41
98 4.65 0.35
*E.C.P (0°) 0.5 4.5
*W.O.T (86°) 4.41 0.59

*E.C.P : Electrically Close Position *W.O.T : Wide Open Throttle

Electronic Throttle Control (ETC) Module Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / Components and Components Location / Component Location illustration
1. Air Cleaner
1-a. 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
1-b. 2.9 - 4,9 N·m (0.3 - 0.5 kgf·m, 2.2 - 3.6 lb·ft, 26.0 - 43.4 lb·in)
2. Electronic Throttle Control (ETC) Module
2-a. 9.8 - 11,8 N·m
3. ETC Module Gasket

Electronic Throttle Control (ETC) Module Description and Operation

Description

  • Electronic Throttle Control (ETC) system is a system that controls the throttle valve electronically.
  • The ETC module consists of a throttle body with an integrated control motor and Throttle Position Sensor (TPS).
  • The Engine Control Module (ECM) uses the Accelerator Position Sensor (APS) signal to calculate the target throttle angle; the position of the throttle is then adjusted by ECM control via the ETC motor.
Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / Description and Operation / Description illustration

Electronic Throttle Control (ETC) Module Troubleshooting

Troubleshooting

Fail-Safe Mode

Item Fail Safe
Electronic Throttle Control (ETC) motor Throttle valve stuck at 9.2°
Throttle Position Sensor (TPS) TPS 1 fault Using the TPS 2 signal
TPS 2 fault Using the TPS 1 signal
TPS 1, 2 fault Throttle valve stuck at 9.2°
Accelerator Position Sensor (APS) APS 1 fault Using the APS 2 signal
APS 2 fault Using the APS 1 signal
APS 1, 2 fault Throttle valve stuck at 9.2°

Information
When throttle value is stuck at 9.2°, engine speed is limited at below 1,500 rpm and vehicle speed at maximum 40 - 50 km/h.

Electronic Throttle Control (ETC) Module On Vehicle Inspection

On Vehicle Inspection

  1. The engine control system can be more quickly diagnosed for problems by using the KDS (Refer to "DTC guide").
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) using the KDS (Refer to DTC guide when fault code is found)
    2. Data analysis : Checking the system input/output data state (Data Analysis → System Selection → Engine)
    3. Actuation test : Checking the system operation condition (Data Analysis → System Selection → Engine → Actuation test → ETC Motor)
    Information
    Refer to the KDS screen for operating conditions and details
Component Inspection

Throttle Position Sensor (TPS)

  1. Disconnect the electronic throttle control (ETC) connector (A).
    Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / On Vehicle Inspection illustration
  2. Connect the KDS.
  3. Start the engine and measure the output voltage of TPS 1 and 2 at E.C.P and W.O.T.
    Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / On Vehicle Inspection illustration
    Terminal Function
    3 Sensor ground
    4 Sensor 2
    6 Sensor 1

    Item Specification
    Sensor Output Voltage (V) Throttle angle (°) TPS 1 TPS 2
    0 0.5 4.5
    10 0.96 4.05
    20 1.41 3.59
    30 1.87 3.14
    40 2.32 2.68
    50 2.78 2.23
    60 3.23 1.77
    70 3.69 1.32
    80 4.14 0.86
    90 4.60 0.41
    98 4.65 0.35
    *E.C.P (0°) 0.5 4.5
    *W.O.T (86°) 4.41 0.59

    *E.C.P : Electrically Close Position *W.O.T : Wide Open Throttle

Electronic Throttle Control (ETC) Motor

  1. Disconnect the electronic throttle control (ETC) connector (A).
    Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / On Vehicle Inspection illustration
  2. Measure resistance between the ETC module terminals 1 and 2 after disconnecting the connector.

    Coil resistance (Ω) : 0.3 - 100 [20 °C]

    Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / On Vehicle Inspection illustration
    Terminal Function
    1 Motor ( - )
    2 Motor ( + )

Electronic Throttle Control (ETC) Module Removal and Installation

Removal

  1. Disconnect the battery negative ( - ) terminal.
  2. Remove the air cleaner assembly. (Refer to Engine Mechanical System - "Air Cleaner")
  3. Disconnect the ETC module connector (A).
    Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / Removal and Installation / Removal illustration
  4. Remove the ETC module (A) by removing the bolts.

    Tightening torque : 9.8 - 11,8 N·m

    Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.
    Note
    • Install the Electronic Throttle Control (ETC) module to the specified torque.
    • If the ETC module is dropped, it may cause internal damage. (Do not reuse)
    • Replace with a new gasket (A) and check to verify that the gasket seats properly before Installation.
      Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / Removal and Installation / Installation illustration
  2. Reset the Engine Control Module (ECM) adaptive values after replacing the ETC. (S/W Management → Engine Control → Resetting Adaptive Values)
    Information
    Refer to the KDS screen for operating conditions and details
  3. Perform the Electronic Throttle Control (ETC) module learning procedure. (Refer to Electronic Throttle Control (ETC) Module - "Adjustment")

Electronic Throttle Control (ETC) Module Adjustment

Adjustment

Note
  • Must perform the Electronic Throttle Control (ETC) learning procedure after replacing or reinstalling the ETC.
  • If not performing the ETC learning procedure after replacing or re-installing, MIL or DTCs might occur.
  1. Wait for 1 minute with the IG ON.
  2. Start the engine and keep the idle status for 15 minutes.
  3. Waif for 1 minute with the IG OFF.
  4. Restart the engine, check that the idle speed is stable.

Electronic Throttle Control (ETC) Module Cleaning

Cleaning

  1. Remove the Electronic Throttle Control (ETC) module. (Refer to Electronic Throttle Control (ETC) Module - "Removal and Installation")
    Note
    Cleaning the ETC after removing it.
  2. Using a cleaner and soft cloth to clean the contaminated area inside the throttle body.
    Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / Cleaning illustration
    Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / Cleaning illustration
    Note
    • Be careful not to get foreign matter into the ETC.
    • Do not spray cleaning fluid to ETC directly and use a lint free cloth moistened with throttle cleaning fluid.
    • Be careful as fingers or cloth may get caught in the valve.
    • Be careful not to wipe the coating liquid (displayed area) around the shaft. If the coating liquid is removed, a poor idle control may occur due to the inflow of foreign matters into the shaft inner bearing and an excessive amount of air leaking.
  3. Install the ETC module. (Refer to Electronic Throttle Control (ETC) Module - "Removal and Installation")

Engine Control Module (ECM) Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Engine Control Module (ECM) / Components and Components Location / Component Location illustration
1. Battery Clamp
1-a. 8.8 - 13,7 N·m
2. Battery
3. Engine Control Module (ECM)

Engine Control Module (ECM) On Vehicle Inspection

On Vehicle Inspection

  1. The engine control system can be more quickly diagnosed for problems by using the KDS (Refer to "DTC guide").
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) using the KDS (Refer to DTC guide when fault code is found)
    2. S/W Management : Controlling other features including system option setting and zero point adjustment (S/W Management → Engine Control → Resetting Adaptive Values)
    Information
    Refer to the KDS screen for operating conditions and details

Engine Control Module (ECM) Removal and Installation

Removal

  1. Perform the IVT oil pressure characteristics backup procedure using the KDS when replacing with a new ECM.
    1. Select the "Oil-pressure Characteristics input" in the S/W Management of KDS.
    2. Select Backup.
  2. Remove the battery. (Refer to Engine Electrical System - "Battery")
  3. Disconnect the Engine Control Module (ECM) connectors (A).
    Engine Control / Fuel System — Engine Control System / Engine Control Module (ECM) / Removal and Installation / Removal illustration
  4. Remove the ECM (A) after removing the bolts.

    Tightening torque : 9.8 - 11,8 N·m

    Engine Control / Fuel System — Engine Control System / Engine Control Module (ECM) / Removal and Installation / Removal illustration
  5. Remove the ECM (A) from the bracket after removing the nuts.

    Tightening torque : 9.8 - 11,8 N·m

    Engine Control / Fuel System — Engine Control System / Engine Control Module (ECM) / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.
    Note
    • Install the Engine Control Module (ECM) to the specified torque.
    • If the ECM is dropped, it may cause internal damage. (Do not reuse)
  2. ECM should be performed the reset and learning procedure after replacing it with a new one. (Refer to Engine Control Module (ECM) - "Adjustment")

Engine Control Module (ECM) Inspection

Inspection

  1. TEST Engine Control Module (ECM) GROUND CIRCUIT: Measure resistance between ECM and chassis ground using the backside of ECM harness connector as ECM side check point. If the problem is found, repair it.

    Specification : 1 Ω or less

  2. TEST ECM CONNECTOR: Disconnect the ECM connector and visually check the ground terminals on ECM side and harness side for bent pins or poor contact pressure. If the problem is found, repair it.
  3. If problem is not found in Step 1 and 2, the ECM could be faulty. If so, replace the ECM with a new one, and then check the vehicle again. If the vehicle operates normally then the problem was likely with the ECM.
  4. RE-TEST THE ORIGINAL ECM : Install the original ECM (may be broken) into a known-good vehicle and check the vehicle. If the problem occurs again, replace the original ECM with a new one. If problem does not occur, this is intermittent problem (Refer to Intermittent Problem Procedure in Basic Inspection Procedure)

Engine Control Module (ECM) Adjustment

Adjustment

Information
Perform inspecting procedure by using the KDS as below order.
Engine Control / Fuel System — Engine Control System / Engine Control Module (ECM) / Adjustment illustration
  1. Perform the procedures below by using the KDS when replacing the Engine Control Module (ECM) with a reused one.
    Information
    Refer to the KDS screen for operating conditions and details
    1. Perform the resetting adaptive values. (S/W Management → Engine Control → Resetting Adaptive Values)
    2. Perform the immobilizer neutral mode / smart key neutralization mode.
      • Non-Smart Key type (S/W Management → Immobilizer → Neutral Mode)
      • Smart Key type (S/W Management → Smart Key Unit → Neutralization Mode)
    3. Perform the auto detected configuration reset. (S/W Management → Engine Control → Auto Detected Configuration Reset)
  2. Perform the "Key Teaching" procedure by using the KDS.
    • Non-Smart Key type (S/W Management → Immobilizer → LEARNT KEYS)
    • Smart Key type Turn IG ON then OFF using the smart key or start button. Then the ECM learns information on the smart key automatically.
  3. Perform the VIN writing procedure by using the KDS. (S/W Management → Engine Control → Write VIN)
  4. Perform the Electronic Throttle Control (ETC) module learning procedure. (Refer to Engine Control / Fuel System - "Electronic Throttle Control (ETC) Module")

Engine Coolant Temperature Sensor (ECTS) Specification

Specification

Temperature Resistance (kΩ)
°C °F
-40 -40 48.14
-20 -4 14.13 - 16.83
0 32 5.79
20 68 2.31 - 2.59
40 104 1.148
60 140 0.5865
80 176 0.3222
100 212 0.1884
110 230 0.1451 - 0.1473
120 248 0.1163

Engine Coolant Temperature Sensor (ECTS) Components and Components Location

Component

Engine Control / Fuel System — Engine Control System / Engine Coolant Temperature Sensor (ECTS) / Components and Components Location / Component illustration
1. Battery Clamp
1-a. 8.8 - 13,7 N·m
2. Battery Insulation Pad
3. Battery
4. Engine Coolant Temperature Sensor (ECTS)
4-a. 19.6 - 39 N·m

Engine Coolant Temperature Sensor (ECTS) Description and Operation

Description

  • Engine Coolant Temperature Sensor (ECTS) detects the engine coolant temperature.
  • The thermistor of ECTS has a characteristic of Negative Temperature Coefficient (NTC), which means temperature and resistance are inversely proportional to each other.
  • The reference +5 V is supplied to the ECTS via a resistor in the Engine Control Module (ECM). That is, the resistor in the ECM and the thermistor in the ECTS are connected in series.
  • To prevent the engine stop or hesitation during the cold start, the ECM calibrates the fuel injection amount and the injection timing based on the engine coolant temperature information.
Engine Control / Fuel System — Engine Control System / Engine Coolant Temperature Sensor (ECTS) / Description and Operation / Description illustration

Engine Coolant Temperature Sensor (ECTS) On Vehicle Inspection

On Vehicle Inspection

  1. The engine control system can be more quickly diagnosed for problems by using the KDS (Refer to "DTC guide").
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) using the KDS (Refer to DTC guide when fault code is found)
      Information
      Refer to the KDS screen for operating conditions and details

Component Inspection

  1. Check the coolant temperature by using the KDS.
  2. Disconnect the Engine Coolant Temperature Sensor (ECTS) connector (A).
    Engine Control / Fuel System — Engine Control System / Engine Coolant Temperature Sensor (ECTS) / On Vehicle Inspection illustration
  3. Measure resistance after disconnecting the ECTS connector.
    Temperature Resistance (kΩ)
    °C °F
    -40 -40 48.14
    -20 -4 14.13 - 16.83
    0 32 5.79
    20 68 2.31 - 2.59
    40 104 1.148
    60 140 0.5865
    80 176 0.3222
    100 212 0.1884
    110 230 0.1451 - 0.1473
    120 248 0.1163

Engine Coolant Temperature Sensor (ECTS) Removal and Installation

Removal

  1. Disconnect the battery negative ( - ) terminal.
  2. Drain the coolant. (Refer to Engine Mechanical System - "Coolant")
  3. Disconnect the Engine Coolant Temperature Sensor (ECTS) connector (A).
    Engine Control / Fuel System — Engine Control System / Engine Coolant Temperature Sensor (ECTS) / Removal and Installation / Removal illustration
  4. Remove the ECTS (A).

    Tightening torque : 19.6 - 39 N·m

    Engine Control / Fuel System — Engine Control System / Engine Coolant Temperature Sensor (ECTS) / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.
    Note
    • Install the Engine Coolant Temperature Sensor (ECTS) to the specified torque.
    • If the ECTS is dropped, it may cause internal damage. (Do not reuse)
    • Apply the engine coolant to the O-ring.
    • Install the ECTS by pushing it into the mounting hole when installing it. At this time do not impact the sensor.
  2. Refill with coolant. (Refer to Engine Mechanical System - "Coolant")

Heated Oxygen Sensor (HO2S) Specification

Specification

Front Heated Oxygen Sensor

Item Specification
Operating voltage (V) 12
Heater resistance (Ω) 2.5 (Room temperature)
Heater control frequency (Hz) ≥100
Heater capacity (W) 8.1
Current consumption (A) 1.2

Rear Heated Oxygen Sensor

Item Specification
Operating voltage (V) 12
Heater resistance (Ω) 3 (Room temperature)
Heater control frequency (Hz) ≥10
Heater capacity (W) 7
Current consumption (A) 1.5

Heated Oxygen Sensor (HO2S) Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Components and Components Location / Component Location illustration
1. Front Heated Oxygen Sensor (HO2S)
1-a. 39.3 - 49 N·m
2. Rear Heated Oxygen Sensor (HO2S)
2-a. 39.3 - 49 N·m

Heated Oxygen Sensor (HO2S) Description and Operation

Description

  • Heated Oxygen Sensor (HO2S), consisting of zirconium and alumina, is installed on both upstream and downstream of the Manifold Catalytic Converter (MCC) to detect the air/fuel ratio and send it to the Engine Control Module (ECM).
  • In order that this sensor operates properly, the temperature of the sensor tip must be higher than 370 °C. For this reason, a heater controlled by the ECM duty signal, is built into the sensor.
  • When the exhaust gas temperature is lower than the specified value, the heater warms the sensor tip.
Front
Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Description and Operation / Description illustration
Rear
Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Description and Operation / Description illustration

Heated Oxygen Sensor (HO2S) On Vehicle Inspection

On Vehicle Inspection

  1. The engine control system can be more quickly diagnosed for problems by using the KDS (Refer to "DTC guide").
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) using the KDS (Refer to DTC guide when fault code is found)
    2. Data analysis : Checking the system input/output data state (Data Analysis → System Selection → Engine)
    Information
    Refer to the KDS screen for operating conditions and details
  2. Disconnect the Heated Oxygen Sensor (HO2S) connector (A).
    Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / On Vehicle Inspection illustration
    Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / On Vehicle Inspection illustration
  3. Measure resistance between the HO2S terminals. Front Heated Oxygen Sensor
    Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / On Vehicle Inspection illustration
    Terminal Function
    2 Heater ( + )
    5 Heater ( - )

    Rear Heated Oxygen Sensor
    Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / On Vehicle Inspection illustration
    Terminal Function
    3 Heater ( + )
    4 Heater ( - )
  4. Check that the resistance is within the specification.
    Item Specification
    Front heated oxygen sensor (Ω) 2.5 (Room temperature)
    Rear heated oxygen sensor (Ω) 3.0 (Room temperature)
Component Inspection

Heated Oxygen Sensor (HO2S) Removal and Installation

Special Service Tool

Tool Name / Number Illustration Description
Heated oxygen sensor socket
09392 - 1Y100
Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Removal and Installation / Special Service Tool illustration
Used for removing / installing the heated oxygen sensor
※ SST 09392 - 2H100 also can be used

Removal

Caution
Wait until cooling the engine for preventing the scalding by high temperature from the exhaust system.
Front Heated Oxygen Sensor (HO2S)
  1. Disconnect the battery negative ( - ) terminal.
  2. Disconnect the front Heated Oxygen Sensor (HO2S) connector (A).
    Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Removal and Installation / Removal illustration
  3. Separate the front HO2S connector (A) by pulling it in the direction of the arrow from the bracket.
    Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Removal and Installation / Removal illustration
  4. Remove the front HO2S (A) by using the SST.

    Tightening torque : 39.2 - 49 N·m

    Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Removal and Installation / Removal illustration
  5. Disconnect the battery negative ( - ) terminal.
  6. Disconnect the rear Heated Oxygen Sensor (HO2S) connector (A).
    Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Removal and Installation / Removal illustration
  7. Separate the rear HO2S connector (A) by pulling it in the direction of the arrow from the bracket.
    Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Removal and Installation / Removal illustration
  8. Separate the rear HO2S wiring (A) from the fixing clips.
    Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Removal and Installation / Removal illustration
  9. Remove the rear HO2S (A).

    Tightening torque : 39.2 - 49 N·m

    Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Removal and Installation / Removal illustration
Rear Heated Oxygen Sensor (HO2S)

Installation

  1. Install in reverse order of removal.
    Note
    • Install the Heated Oxygen Sensor (HO2S) to the specified torque.
    • If HO2S is dropped, it may cause internal damage. (Do not reuse)
    • Do not use oil components such as cleaners, sprays, or greases on the sensing part and connector as it may degrade the performance of HO2S.
    • The sensor or the wiring can be damaged by being contacted to the exhaust system (Exhaust manifold, Catalytic converter etc.).
  2. Reset the ECM adaptive value after replacing the heated oxygen sensor. (S/W Management → Engine → Resetting Adaptive Values)
    Information
    Refer to the KDS screen for operating conditions and details

Intake Middle Lock Control Solenoid Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Intake Middle Lock Control Solenoid / Components and Components Location / Component Location illustration
1. Intake Middle Lock Control Solenoid
1-a. 8.8 - 9,8 N·m

Intake Middle Lock Control Solenoid Description and Operation

Description

  • The Continuous Variable Valve Timing (CVVT) system uses Engine Control Module (ECM) control signals that vary with engine RPM and load to advance or retard the timing of opening/closing the intake or exhaust valve.
  • According to the valve overlap and underlap between the intake and exhaust valve by CVVT, there are effects such as reduce the pumping loss, occur internal EGR and improve the combustion stability and volumetric efficiency. For these reasons, fuel efficiency and engine performance are improved, and the exhaust gas (NOx, HC) decreases.
  • The CVVT Oil Control Valve (OCV) supplies or discharges the oil to a cam phaser by changing the path of engine oil, receiving the PWM (Pulse Width Modulation) signal of ECM.
  • The oil from the OCV changes the phase of the cam shaft by advancing or retarding the cam shaft by rotating the rotor connected to the cam shaft inside the cam phaser.
Engine Control / Fuel System — Engine Control System / Intake Middle Lock Control Solenoid / Description and Operation / Description illustration

Intake Middle Lock Control Solenoid On Vehicle Inspection

On Vehicle Inspection

  1. The engine control system can be more quickly diagnosed for problems by using the KDS (Refer to "DTC guide").
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) using the KDS (Refer to DTC guide when fault code is found)
    Information
    Refer to the KDS screen for operating conditions and details

Intake Middle Lock Control Solenoid Removal and Installation

Removal

  1. Disconnect the battery negative ( - ) terminal.
  2. Remove the engine cover. (Refer to Engine Mechanical System - "Engine Cover")
  3. Disconnect the intake middle lock control solenoid connector (A).
    Engine Control / Fuel System — Engine Control System / Intake Middle Lock Control Solenoid / Removal and Installation / Removal illustration
  4. Separate the connector (A) from the bracket and separate the fixing holder (B).
    Engine Control / Fuel System — Engine Control System / Intake Middle Lock Control Solenoid / Removal and Installation / Removal illustration
  5. Remove the intake middle lock control solenoid (A) after removing the screws.

    Tightening torque : 8.8 - 9,8 N·m

    Engine Control / Fuel System — Engine Control System / Intake Middle Lock Control Solenoid / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.
    Note
    • Install the intake middle lock control solenoid to the specified torque.
    • If the intake middle lock control solenoid is dropped, it may cause internal damage. (Do not reuse)
    • Apply the engine oil to the O-ring.

Knock Sensor (KS) Specification

Specification

Item Specification
Capacitance (pF) 850 - 1,150

Knock Sensor (KS) Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Knock Sensor (KS) / Components and Components Location / Component Location illustration
1. Engine Cover
2. Intake Manifold Bracket
2-a. 18.6 - 24 N·m
3. Intake Manifold
3-a. 18.6 - 24 N·m
4. Knock Sensor (KS)
4-a. 18.6 - 24 N·m

Knock Sensor (KS) Description and Operation

Description

  • The Knock Sensor (KS) detects vibration when knocking and transmits to the Engine Control Module (ECM).
  • The knocking sensor outputs a knocking signal when knocking, and the ECM that receives the signal to prevent the knocking by perceiving the timing of ignition. If there is no knocking signal, ECM which controls the timing of ignition continuously to ensure the optimum torque and fuel efficiency.
Engine Control / Fuel System — Engine Control System / Knock Sensor (KS) / Description and Operation / Description illustration

Knock Sensor (KS) On Vehicle Inspection

On Vehicle Inspection

  1. The engine control system can be more quickly diagnosed for problems by using the KDS (Refer to "DTC guide").
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) using the KDS (Refer to DTC guide when fault code is found)
    2. Data analysis : Checking the system input/output data state (Data Analysis → System Selection → Engine)
    Information
    Refer to the KDS screen for operating conditions and details

Component Inspection

  1. Check signal waveform of Knock Sensor (KS) by using a KDS.

    Specified value : Refer to "DTC diagnostic guide"

Knock Sensor (KS) Removal and Installation

Removal

  1. Remove the intake manifold. (Refer to Engine Mechanical System - "Intake Manifold")
  2. Remove the Knock Sensor (KS) (A) after removing the fixing clip (B).

    Tightening torque : 18.6 - 24 N·m

    Engine Control / Fuel System — Engine Control System / Knock Sensor (KS) / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.
    Note
    • Install the Knock Sensor (KS) to the specified torque.
    • If the KS is dropped, it may cause internal damage. (Do not reuse)

Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) Specification

Specification

Item Specification
Rated voltage (V) 5
Operating voltage (V) 4.75 - 5.25
Current consumption (mA) 10
Pressure [kPa (kg/cm², psi)] 20 - 101.32 (0.2 - 1.03, 2.9 - 14.70)

Pressure Signal
Pressure Output Voltage (V)
kPa kg/cm² psi
20 0.20 2.90 0.789
46.66 0.48 6.78 1.842
101.32 1.03 14.70 4.000

Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) / Components and Components Location / Component Location illustration
1. Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS)
1-a. 9.8 - 11,8 N·m

Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) Description and Operation

Description

Manifold Absolute Pressure Sensor (MAPS)

  • Manifold Absolute Pressure Sensor (MAPS) is a speed-density type sensor that senses absolute pressure of the Intake Manifold.
  • MAPS transfers the analog signal proportional to the pressure to the Engine Control Module (ECM).
  • By using this signal, the ECM calculates the intake air amount and engine speed.

Intake Air Temperature Sensor (IATS)

  • Intake Air Temperature Sensor (IATS) is included inside MAPS and detects the intake air temperature.
  • To calculate precise air quantity, correction of the air temperature is needed because air density varies according to the temperature. So the ECM uses not only MAPS signal but also IATS signal.
  • This sensor has a Negative Temperature Coefficient (NTC) Thermistor and it's resistance changes in reverse proportion to the temperature.
Engine Control / Fuel System — Engine Control System / Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) / Description and Operation / Description illustration

Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) On Vehicle Inspection

On Vehicle Inspection

  1. The engine control system can be more quickly diagnosed for problems by using the KDS (Refer to "DTC guide").
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) using the KDS (Refer to DTC guide when fault code is found)
    2. Data analysis : Checking the system input/output data state (Data Analysis → System Selection → Engine)
    Information
    Refer to the KDS screen for operating conditions and details

Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) Removal and Installation

Removal

  1. Disconnect the battery negative ( - ) terminal.
  2. Remove the air cleaner assembly. (Refer to Engine Mechanical System - "Air Cleaner")
  3. Disconnect the Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) connector (A).
    Engine Control / Fuel System — Engine Control System / Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) / Removal and Installation / Removal illustration
  4. Remove the MAPS & IATS (A) after removing the bolt.

    Tightening torque : 9.8 - 11,8 N·m

    Engine Control / Fuel System — Engine Control System / Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.
    Note
    • Install the Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) to the specified torque.
    • If the MAPS & IATS is dropped, it may cause internal damage. (Do not reuse)

Oil Pressure Sensor (OPS) Specification

Specification

Item Specification
Rated voltage (V) 12
Operating pressure [kgf / cm² (kPa, psi)] 0.2 - 0.4 (19.61 - 39.22, 2.84 - 5.68)
Load (W) Maximum 5

Oil Pressure Sensor (OPS) Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Oil Pressure Sensor (OPS) / Components and Components Location / Component Location illustration
1. Oil Pressure Sensor (OPS)
1-a. 9.8 - 11,8 N·m

Oil Pressure Sensor (OPS) On Vehicle Inspection

On Vehicle Inspection

  1. The engine control system can be more quickly diagnosed for problems by using the KDS (Refer to "DTC guide").
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) using the KDS (Refer to DTC guide when fault code is found)
    Information
    Refer to the KDS screen for operating conditions and details

Oil Pressure Sensor (OPS) Removal and Installation

Removal

  1. Disconnect the battery negative ( - ) terminal.
  2. Remove the engine compartment under cover. (Refer to Engine Mechanical System - "Engine Room Under Cover")
  3. Disconnect the Oil Pressure Sensor (OPS) connector (A).
    Engine Control / Fuel System — Engine Control System / Oil Pressure Sensor (OPS) / Removal and Installation / Removal illustration
  4. Remove the OPS (A).

    Tightening torque : 9.8 - 11,8 N·m

    Engine Control / Fuel System — Engine Control System / Oil Pressure Sensor (OPS) / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.
    Note
    • Install the Oil Pressure Sensor (OPS) to the specified torque.
    • If the OPS is dropped, it may cause internal damage. (Do not reuse)
    • Be careful not to get engine oil and/or coolant flow into the OPS connector.
    • Apply the seal lock to part (A) when installing the OPS.

      Thickness : 0.2 - 0.4 mm (0.0078 - 0.0157 in)

      Engine Control / Fuel System — Engine Control System / Oil Pressure Sensor (OPS) / Removal and Installation / Installation illustration

Variable Charge Motion Actuator (VCMA) Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Variable Charge Motion Actuator (VCMA) / Components and Components Location / Component Location illustration
1. Variable Charge Motion Actuator (VCMA)
1-a. 9.8 - 11,8 N·m

Variable Charge Motion Actuator (VCMA) Removal and Installation

Removal

  1. Disconnect the battery negative ( - ) terminal.
  2. Remove the engine cover. (Refer to Engine Mechanical System - "Engine Cover")
  3. Disconnect the Variable Charge Motion Actuator (VCMA) connector (A).
    Engine Control / Fuel System — Engine Control System / Variable Charge Motion Actuator (VCMA) / Removal and Installation / Removal illustration
  4. Remove the VCMA (A) after removing the bolts.

    Tightening torque : 9.8 - 11,8 N·m

    Engine Control / Fuel System — Engine Control System / Variable Charge Motion Actuator (VCMA) / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.
    Note
    • Install the Variable Charge Motion Actuator (VCMA) to the specified torque.
    • If the VCMA is dropped, it may cause internal damage. (Do not reuse)

Variable Intake Solenoid (VIS) Valve Specification

Specification

Item Specification
Operating voltage (V) 9 - 16 [22 °C]
Coil resistance (Ω) 30 - 35 [22 °C]

Variable Intake Solenoid (VIS) Valve Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Variable Intake Solenoid (VIS) Valve / Components and Components Location / Component Location illustration
1. Variable Intake Solenoid (VIS) Valve
1-a. 9.8 - 11,8 N·m

Variable Intake Solenoid (VIS) Valve Description and Operation

Description

  • The Variable Intake Solenoid (VIS) valve works as controlling the vacuum valve in intake manifold.
  • This valve is controlled by the Engine Control Module (ECM) control signal according to the engine driving condition.
    Engine Control / Fuel System — Engine Control System / Variable Intake Solenoid (VIS) Valve / Description and Operation / Description illustration

Variable Intake Solenoid (VIS) Valve On Vehicle Inspection

On Vehicle Inspection

  1. The engine control system can be more quickly diagnosed for problems by using the KDS (Refer to "DTC guide").
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) using the KDS (Refer to DTC guide when fault code is found)
    2. Actuation test : Checking the system operation condition (Data Analysis → System Selection → Engine → Actuation test → Variable Intake Manifold (Both ECU Output))
    Information
    Refer to the KDS screen for operating conditions and details
  2. Turn the ignition switch OFF.
  3. Disconnect the Variable Intake Solenoid (VIS) Valve connector.
  4. Measure resistance between VIS valve terminals.
    Item Specification
    Coil resistance (Ω) 30 - 35 [22 °C]
Component Inspection

Variable Intake Solenoid (VIS) Valve Removal and Installation

Removal

  1. Disconnect the battery negative ( - ) terminal.
  2. Disconnect the Variable Intake Solenoid (VIS) valve connector (A) and vacuum hose (B).
    Engine Control / Fuel System — Engine Control System / Variable Intake Solenoid (VIS) Valve / Removal and Installation / Removal illustration
  3. Remove the VIS valve (A) after removing the bolts and nut.

    Tightening torque : 9.8 - 11,8 N·m

    Engine Control / Fuel System — Engine Control System / Variable Intake Solenoid (VIS) Valve / Removal and Installation / Removal illustration
    Engine Control / Fuel System — Engine Control System / Variable Intake Solenoid (VIS) Valve / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.
    Note
    • Install the Variable Intake Solenoid (VIS) valve to the specified torque.
    • If the VIS valve is dropped, it may cause internal damage. (Do not reuse)
    • Be careful not to get foreign matters into the VIS valve.