Single-Use Parts

Rear Axle Assembly

22steps
~132min
4/5difficulty
010203040505.94N·mlb·ft
Tightening torque found on this page
Done 0 of 22

Contents:

Components and Components Location

Component

2WD - CTBA

Driveshaft and Axle — Rear Axle Assembly / Components and Components Location / Component illustration
1. Rear Brake Disc
1-a. 4.9 - 5,9 N·m (0.5 - 0.6 kgf·m, 3.6 - 4.3 lb·ft, 43.4 - 52.1 lb·in)
2. Rear Hub Assembly
2-a. 63.7 - 74 N·m
3. Rear Dust Cover
3-a. 24.5 - 34 N·m
4. Rear Knuckle

4WD - Multi Link

Driveshaft and Axle — Rear Axle Assembly / Components and Components Location / Component illustration
1. Rear Brake Disc
1-a. 4.9 - 5,9 N·m (0.5 - 0.6 kgf·m, 3.6 - 4.3 lb·ft, 43.4 - 52.1 lb·in)
2. Rear Hub Assembly
2-a. 88.3 - 108 N·m
3. Rear Dust Cover
3-a. 6.9 - 10,8 N·m
4. Rear Carrier
4-a. 137.3 - 157 N·m
4-b. 117.7 - 132 N·m
4-c. 117.7 - 132 N·m

Rear Hub Assembly Removal and Installation - 2WD

Removal

  1. Remove the rear wheel and tires. (Refer to Suspension System - "Wheel")
  2. Remove the rear brake disc. (Refer to Brake System - "Rear Brake Disc")
  3. Remove the rear wheel speed sensor (A).
    Driveshaft and Axle — Rear Axle Assembly / Rear Hub Assembly / Removal and Installation - 2WD / Removal illustration
  4. Remove the rear hub assembly and dust cover (A) after removing the rear hub assembly bolts.

    Tightening torque : 49.0 - 59 N·m

    Driveshaft and Axle — Rear Axle Assembly / Rear Hub Assembly / Removal and Installation - 2WD / Removal illustration
    Driveshaft and Axle — Rear Axle Assembly / Rear Hub Assembly / Removal and Installation - 2WD / Removal illustration

Installation

  1. Install in reverse order of removal.

Rear Hub Assembly Removal and Installation - 4WD

Special Service Tool

Tool Name / Number Illustration Description
CV joint puller
09517 - 4E000
Driveshaft and Axle — Rear Axle Assembly / Rear Hub Assembly / Removal and Installation - 4WD / Special Service Tool illustration
Used for removal of CV joint

Removal

  1. Remove the rear brake disc. (Refer to Brake System - "Rear Brake Disc")
  2. Unlock the rear driveshaft lock nut caulking (A), by hammering on a chisel or suitable tool.
    Driveshaft and Axle — Rear Axle Assembly / Rear Hub Assembly / Removal and Installation - 4WD / Removal illustration
  3. Remove the rear driveshaft lock nut (A).

    Tightening torque : 274.6 - 294 N·m

    Driveshaft and Axle — Rear Axle Assembly / Rear Hub Assembly / Removal and Installation - 4WD / Removal illustration
  4. Separate the rear driveshaft (A) from the rear hub assembly using the SST (09517 - 4E000).
    Driveshaft and Axle — Rear Axle Assembly / Rear Hub Assembly / Removal and Installation - 4WD / Removal illustration
  5. Remove the rear hub assembly (B) after removing the rear hub assembly bolts (A).

    Tightening torque : 88.3 - 108 N·m

    Driveshaft and Axle — Rear Axle Assembly / Rear Hub Assembly / Removal and Installation - 4WD / Removal illustration
    Driveshaft and Axle — Rear Axle Assembly / Rear Hub Assembly / Removal and Installation - 4WD / Removal illustration

Installation

  1. Install in reverse order of removal.

Rear Hub Assembly Inspection

Inspection

  1. Check the rear hub assembly for wear and damage.

Rear Dust Cover Removal and Installation - 2WD

Removal

  1. Remove the rear hub assembly. (Refer to Rear Axle Assembly - "Rear Hub Assembly")
  2. Remove the rear dust cover (A) after removing the bolts.

    Tightening torque : 24.5 - 34 N·m

    Driveshaft and Axle — Rear Axle Assembly / Rear Dust Cover / Removal and Installation - 2WD / Removal illustration

Installation

  1. Install in reverse order of removal.

Rear Dust Cover Removal and Installation - 4WD

Removal

  1. Remove the rear hub assembly. (Refer to Rear Axle Assembly - "Rear Hub Assembly")
  2. Remove the EPB extension wire clip (A) from the dust cover.
    Driveshaft and Axle — Rear Axle Assembly / Rear Dust Cover / Removal and Installation - 4WD / Removal illustration
  3. Remove the rear dust cover (A) after removing the bolts.

    Tightening torque : 6.9 - 10,8 N·m

    Driveshaft and Axle — Rear Axle Assembly / Rear Dust Cover / Removal and Installation - 4WD / Removal illustration

Installation

  1. Install in reverse order of removal.

Rear Dust Cover Inspection

Inspection

  1. Check the rear dust cover for scratches or damage.

Rear Carrier - 4WD Removal and Installation

Removal

Warning
If a transmission jack is used with a two-post lift, do not lift the vehicle too much. The center gravity of the vehicle may change and fall.
  1. Remove the rear dust cover. (Refer to Rear Axle Assembly - "Rear Dust Cover")
  2. Separate the rear wheel speed sensor (A) after removing the bolt.

    Tightening torque : 6.9 - 10,8 N·m

    Driveshaft and Axle — Rear Axle Assembly / Rear Carrier - 4WD / Removal and Installation / Removal illustration
  3. Separate the rear trailing arm from the rear carrier after removing the bolt (A) and washer (B).

    Tightening torque : 137.3 - 157 N·m

    Driveshaft and Axle — Rear Axle Assembly / Rear Carrier - 4WD / Removal and Installation / Removal illustration
    Note
    • Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
    • Be careful not to change the direction of the bolt and washer when installing.
  4. Separate the rear assist arm from the rear carrier after removing the bolt (A), washer (B), and nut (C).

    Tightening torque : 137.3 - 157 N·m

    Driveshaft and Axle — Rear Axle Assembly / Rear Carrier - 4WD / Removal and Installation / Removal illustration
    Note
    • Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
    • Be careful not to change the direction of the bolt, washer, and nut when installing.
    Information
    Fix the bolt and remove or install the nut.
  5. Separate the rear upper arm from the rear carrier after removing the bolt (A) and nut (B).

    Tightening torque : 137.3 - 157 N·m

    Driveshaft and Axle — Rear Axle Assembly / Rear Carrier - 4WD / Removal and Installation / Removal illustration
    Note
    • Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
    • Be careful not to change the bolt, nut and washer installing position.
    Information
    Fix the bolt and remove or install the nut.
  6. Remove the rear carrier (A) after removing the bolt and nut.

    Tightening torque : 137.3 - 157 N·m

    Driveshaft and Axle — Rear Axle Assembly / Rear Carrier - 4WD / Removal and Installation / Removal illustration
    Note
    • Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
    • Be careful not to change the bolt, nut and washer installing position.
    Information
    Fix the bolt and remove or install the nut.

Installation

  1. Install in reverse order of removal.
  2. Check the alignment. (Refer to Suspension System - "Alignment")

Rear Carrier - 4WD Inspection

Inspection

  1. Check the rear carrier for cracks.