Kia Stinger CK Quiz
Engine Control System/Fuel System

Brake Switch

In this manual: Engine Control System/Fuel System
General Information — 8Maintenance — 27Engine Mechanical System — 47Engine Electrical System — 19Emission Control System — 12Engine Control System/Fuel System — 51Automatic Transmission System — 34All-Wheel Drive (AWD) System — 7Drive Shaft and Axle — 15Suspension System — 25Steering — 8Restraints — 19Brake System — 22Body (Interior and Exterior) — 47Front Seat Belt — 63Body Electrical System — 99Windshield Wiper/Washer — 11Heating, Ventilation, and Air Conditioning — 32
14steps
~84min
3/5difficulty
Done 0 of 14

Components and Component Location

Components

1. Brake Switch 2. Brake Pedal

Circuit Diagrams

Terminal Function

Pin No. Description
1 IGN1
2 IBU
3 -
4 B+
5 Stop Lamp
6 Ground

Troubleshooting

Troubleshooting

  1. Component Inspection

    Items Cause Symptom
    Fuse Switch Loose fuse connection, blown fuse

    • DTC: P0504

    • Symptom: Shift problems, start failure, cruise control cancel function problem, EPB cancel function malfunction, brake light malfunction, ESP OFF lamp ON.

    		 ① Check the signal waveform using an oscilloscope on each part while the vehicle is accelerating/braking. (Refer to Brake Light Switch Circuit Inspection Procedure)

    ② Refer to the applicable part repair procedure if any abnormality is found in the waveform (refer to the repair procedure for the relevant part and replace if necessary)
    Fuse Relay Loose fuse connection, blown fuse

    • DTC: P0504

    • Symptom: Shift problems, start failure, cruise control cancel function problem, EPB cancel function malfunction, brake light malfunction, ESP OFF lamp ON.
    Stop Lamp Switch

    • Damaged wiring of each component

    • Incorrect connector connection

    • Faulty component

    • DTC: P0504

    • Symptom: Shift problems, start failure, cruise control cancel function problem, EPB cancel function malfunction, brake light malfunction, ESP OFF lamp ON.
    Stop Lamp Electronic
    Module (if applicable)

    • DTC: P0504, C2130, C2131

    • Symptom: Shift problems, start failure, cruise control cancel function problem, EPB cancel function malfunction, brake light malfunction, ESP OFF lamp ON.
    Engine Control Module (ECM)

    • DTC: P0504

    • Symptom: Shift problems, cruise control cancel problem
    Body Control Module (BCM)

    • Gear Shifting Concerns
    Shift Lock Solenoid

    • Gear Shifting Concerns
    Inhibitor Switch

    • Symptom: Shift problems, no-start, cruise control cancel problem, EPB release function problem
    Smart Key Unit (SMK)

    • Starting Failure
    Electronic Parking Brake (EPB)

    • Symptom: EPB release function problem, ESP OFF indicator illuminated.
    ABS/VDC Control Unit (Pressure Sensor)

    • Symptom: ESP OFF lamp illuminated.

  2. Symptom Diagnostics

    Symptom Possible Cause
    Starting Problems Switch fuse, relay fuse, brake light switch, electronic brake light module, ABS/VDC control module, each wire, connector ① Check the signal waveform using an oscilloscope on each part while the vehicle is accelerating/braking. (Refer to Brake Light Switch Circuit Inspection Procedure)

    ② Refer to the applicable part repair procedure if any abnormality is found in the waveform (refer to the repair procedure for the relevant part and replace if necessary)
    Gear Shifting Concerns Switch fuse, relay fuse, brake light switch, electronic brake light module, BCM, ECM, inhibitor switch, each wire, connector
    ESP OFF indicator light is on Switch fuse, relay fuse, brake light switch, electronic brake light module, ABS/VDC control module, each wire, connector
    P0504 Switch fuse, relay fuse, brake light switch, electronic brake light module, ECM, each wire, connector
    Stop lamp does not operate Switch fuse, relay fuse, brake light switch, electronic brake light module, wire/connector disconnected
    Stop lamp always
    on    		 Stop lamp switch, stop lamp electronic module,
    Wiring short circuit, blown fuse

  3. Stop Lamp Switch System Diagnosis

    SSEM: Stop Lamp Electronic Module

  4. Refer to the DTC Chart when the applicable DTCs are displayed.

Repair Procedures

Removal

  1. Turn the ignition switch OFF and disconnect the negative (-) battery cable.

  2. Remove the airbag lower panel.

    (Refer to Body - "Under Cover Panel")

  3. Remove the knee airbag.

    (Refer to Restraint System - "Knee Airbag")

  4. Disconnect the stop lamp switch connector (A).

  5. Pull the stopper plate (A) in the direction shown by the arrow, then rotate the brake switch (B) 45° clockwise and remove it.

  6. Inspect the removed stop lamp switch according to the procedures described below.

    1. Confirm proper connection with the terminal part.

      • Confirm that the connector is properly secured and that the connection mark is present.

    2. Perform a resistance check of the parts.

Installation

  1. Hold the brake pedal arm and fully insert the brake switch so that the contact part is not visible.

  2. After inserting, rotate the brake switch 45° counterclockwise, then install the stopper plate by pressing it.

  3. Check the clearance between the stop lamp switch and the bracket.

    Stop lamp switch clearance (A): 1.0-2.0 mm (0.04-0.08 in.)

  4. Connect the stop lamp switch connector (A).

Test yourself

A quick Kia Stinger CK quiz: every answer comes with an explanation and a link to the manual page.