Steering Column

IG2 Signal Malfunction (B2788)

~4min read

DESCRIPTION

This DTC is stored when the steering lock ECU (steering lock actuator or upper support assembly) detects a malfunction in the IG2 power supply.

HINT:

The Steering Lock ECU (Steering Lock Actuator or Upper Support Assembly) is not connected to the CAN communication system. Instead, the Steering Lock ECU (Steering Lock Actuator or Upper Support Assembly) is connected to the Certification ECU (Smart Key ECU Assembly) via LIN communication and communicates with other components via the CAN communication system through the Certification ECU (Smart Key ECU Assembly).

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Note

B2788

IG2 Signal Malfunction

Mismatch between the IG2 input of the Steering Lock ECU (Steering Lock Actuator or Upper Support Assembly) from the LIN communication system and the direct line. (1 trip detection logic (only output when a malfunction is detected and the engine switch is in the ON (IG) position))

  • IGN No. 2 fuse
  • Steering lock ECU (steering lock actuator or upper support assembly)
  • Wire harness or connector

DTC Output Confirmation Operation: No confirmation driving needed (continuous monitoring).

Vehicle Condition and Fail-Safe Function When Malfunction Is Detected

Vehicle Condition When Malfunction Is Detected

Fail-Safe Function When Malfunction Is Detected

The steering cannot be locked or unlocked. Therefore, the engine cannot be started.

-

Related Data List and Active Test Items

DTC No.

Data List Item

Active Test Item

B2788

-

-

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • While using the Techstream with the vehicle engine switch in the OFF position, connect the Techstream to the vehicle and switch a welcome light switch ON and OFF at intervals of no more than 1.5 seconds until communication between the Techstream and the vehicle starts. Then select the vehicle type in manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, regularly switch a welcome light switch between ON and OFF at intervals of no more than 1.5 seconds to maintain communication between the Techstream and the vehicle.
  • The steering lock system uses LIN communication. Therefore, before troubleshooting, first perform the checks described in "How to Proceed with Troubleshooting" to make sure there is no communication malfunction.

    Click here

  • Check the fuses for the circuits related to this system before performing the following procedure.
  • After completing the repairs, check again that no DTCs are output.

    Click here

  • When replacing the steering lock ECU (steering lock actuator or upper support assembly), registration must be performed.

    Click here

PROCEDURE

  1. CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER SUPPORT ASSEMBLY) (POWER SOURCE MODE SIGNAL)

(a) Make sure there is no looseness in the lock and connector connection.

(b) Disconnect connector F78 of the steering lock ECU (steering lock actuator or upper support assembly).

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F78-1 (GND) - Body ground

Always

Below 1 Ω

*a

Front view of wire harness side connector

(to Steering Lock ECU (Steering Lock Actuator or Upper Support Assembly))

(d) Reconnect connector F78 of the steering lock ECU (steering lock actuator or upper support assembly).

(e) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

F78-6 (IG2) - F78-1 (GND)

Engine switch in ON (IG) position

11 à 14 V

F78-6 (IG2) - F78-1 (GND)

Engine switch in OFF position

Below 1 V

*a

Component with Wire Harness Connected

(Steering lock ECU (steering lock actuator or upper support assy))

OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER SUPPORT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR