Steering Column

Data List / Active Test

~18min read

DATA LIST / ACTIVE TEST

READ DATA LIST

HINT:

The Techstream Data List allows you to read the values or status of switches, sensors, actuators and other components without removing any parts. This non-intrusive check can be very useful, since intermittent conditions or signals can be identified before parts or wiring are moved. Reading the Data List during troubleshooting saves time in diagnosis.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not determine whether a part is faulty based only on these reference values.

(a) Turn the engine switch to OFF.

(b) Connect the Techstream to the DLC3.

(c) Turn the engine switch to ON (IG).

(d) Turn on the Techstream.

(e) Select the following menus: Body Electrical / (desired system) / Data List.

(f) Read the Data List by following the Techstream instructions.

(g) Using the Techstream, check the Data List items that will help determine the cause of the problem.

NOTICE:

  • The steering lock ECU (steering lock actuator set or upper support) communicates with the Techstream via the certification ECU (smart key ECU assembly), which uses CAN communication. If there is a malfunction in the CAN communication system or in the certification ECU (smart key ECU assembly), the Data List items may be abnormal.
  • While using the Techstream with the vehicle engine switch in the OFF position, connect the Techstream to the vehicle and switch a welcome light switch ON and OFF at intervals of no more than 1.5 seconds until communication between the Techstream and the vehicle starts. Then select the vehicle type in manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, regularly switch a welcome light switch between ON and OFF at intervals of no more than 1.5 seconds to maintain communication between the Techstream and the vehicle.
Body Electrical > Power Source Control > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Shift P Signal

Shift Lever Position Signal (P)

ON or OFF

ON: Shift lever in P position

OFF: Shift lever in a position other than P

  • Follow this option to determine whether the malfunction is in the shift lever position switch.
  • The engine cannot be started when this function is disabled.

Steering Unlock Switch

Steering unlock sensor status signal output by the steering lock ECU (steering lock actuator set or upper support)

ON or OFF

ON: Steering unlocked

OFF: Steering locked

This item can be used to determine the cause of problems when the steering does not lock or does not unlock.

HINT:

  • The steering is considered locked when the lock sensor is ON and the unlock sensor is OFF.
  • The steering is considered unlocked when the lock sensor is OFF and the unlock sensor is ON.

Str Lock/Unlock Wait T-Out

Steering lock or unlock malfunction

Yes or No

Yes: Steering lock/unlock wait time-out (locking bar stuck, etc.)

No: Steering lock/unlock performed normally within the specified time

The engine cannot be started when this item is "Yes".

Body Electrical > Smart Key > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

# Codes

Number of DTCs

Min: 0

Max.: 255

Number of stored DTCs displayed

-

Immobiliser

Immobiliser system status determined by the certification ECU (smart key ECU assembly)

Set or Unset

Set: Immobiliser activated (engine start disabled) (engine switch in OFF position)

Unset: Immobiliser deactivated (engine start allowed) (engine switch in ON (ACC) or ON (IG) position)

  • When the immobiliser cannot be deactivated, this item can be used to determine whether the certification ECU (smart key ECU assembly) or the ID code box (immobiliser code ECU) is part of the problem.
  • The engine cannot be started when this function displays "Set".

HINT:

  • The immobiliser status (activated or not) can be determined via the certification ECU (smart key ECU assembly). If this item displays "Set", communication between the certification ECU (smart key ECU assembly) and the ID code box (immobiliser code ECU) can be considered normal.
  • The security indicator operation is related only to the immobilizer system status (armed / disarmed) and is not related to the steering lock operation (locked / unlocked). When the immobilizer system is armed, the security indicator flashes.

Steering Lock Sleep Cond

Steering lock ECU sleep availability (steering lock actuator assembly or upper support assembly)

Yes or No

Yes: Sleep available

No: Sleep not available

-

Steering Lock Start Cond

Steering lock ECU activation signal status (steering lock actuator assembly or upper support assembly)

Yes or No

Yes: Activation signal sent

No: Activation signal not sent

-

Engine Start Condition

Status of the engine start permission signal determined by the steering lock ECU (steering lock actuator assembly or upper support assembly) and sent to the certification ECU (smart key ECU assembly)

OK or NG

OK: Engine start permitted

NG: Engine start inhibited

  • When this item shows "OK", the certification ECU (smart key ECU assembly) has received an unlock confirmation signal from the steering lock ECU (steering lock actuator assembly or upper support assembly) and has permitted fuel injection and engine combustion.
  • The engine cannot start when this item shows "NG".

Sensor Value

Malfunction record of the steering lock ECU (steering lock actuator assembly or upper support assembly) lock or unlock sensor

(DTC B2781 is output)

OK or NG (Past)

OK: No malfunction record of the steering lock ECU (steering lock actuator assembly or upper support assembly) lock/unlock sensor

NG (Past): A steering lock ECU (steering lock actuator assembly or upper support assembly) lock/unlock sensor record occurring at the same time as the ON position exists

When this item shows "NG", the sensor inside the steering lock ECU (steering lock actuator assembly or upper support assembly) may be malfunctioning, or there may be a mechanical malfunction.

Power Supply Short

Malfunction record of signal sent from the certification ECU (smart key ECU assembly) to the steering lock motor (steering lock actuator assembly or upper support assembly) (short circuit)

(DTC B2782 is output)

OK or NG (Past)

OK: No malfunction record (short circuit)

NG (Past): Malfunction record (short circuit) detected

This function records malfunctions in the circuit between the certification ECU (smart key ECU assembly) and the steering lock motor (steering lock actuator assembly or upper support assembly).

Motor Driver Short

Malfunction record of the motor drive circuit of the steering lock ECU (steering lock actuator assembly or upper support assembly) (short circuit)

(DTC B2781 is output)

OK or NG (Past)

OK: No malfunction record (short circuit)

NG (Past): Malfunction record (short circuit) detected

This function records malfunctions in the motor drive circuit inside the steering lock ECU (steering lock actuator assembly or upper support assembly) (short circuit).

Lock/Unlock Receive

Reception status of the steering lock or unlock request signal from the certification ECU (smart key ECU assembly)

Yes or No

Yes: Lock or unlock request signal reception recorded

No: No record of lock or unlock request signal reception

-

Lock Bar Stuck Error

Record of the lock bar not unlocking properly for a certain time after being commanded to unlock

OK or NG (Past)

OK: No record of lock bar stuck

NG (Past): Lock bar stuck record detected

-

Engine Start Request

Reception status of the engine start permission signal determined by the steering lock ECU (steering lock actuator assembly or upper support assembly) and sent to the certification ECU (smart key ECU assembly)

OK or NG

OK: Signal received

NG: Signal not received

  • When this item shows "OK", the certification ECU (smart key ECU assembly) has received an unlock confirmation signal from the steering lock ECU (steering lock actuator assembly or upper support assembly) and has permitted fuel injection and engine combustion.
  • The engine cannot start when this item shows "NG".

S Code Check

Verification result between the certification ECU (smart key ECU assembly) and the ID code box (immobilizer ECU)

OK or NG

OK: Verification result normal

NG: Verification result abnormal

When a malfunction has been detected:

  • The ID code for the certification ECU (smart key ECU assembly) or the ID code box (immobilizer ECU) is not registered, or the certification ECU (smart key ECU assembly) or the ID code box (immobilizer ECU) is faulty.
  • The steering cannot be locked.
  • The steering cannot be unlocked (the engine cannot start).

L Code Check

Verification result between the ID code box (immobilizer ECU) and the steering lock ECU (steering lock actuator assembly or upper support assembly)

OK or NG

OK: Verification result normal

NG: Verification result abnormal

When a malfunction has been detected:

  • The ID code of the ID code box (immobilizer ECU) or the steering lock ECU (steering lock actuator assembly or upper support assembly) is not registered, or the ID code box (immobilizer ECU) or the steering lock ECU (steering lock actuator assembly or upper support assembly) is faulty.
  • The steering cannot be locked.
  • The steering cannot be unlocked (the engine cannot start).

Unlock Request Receive

Receiving status of steering unlock request signal sent from the smart key ECU assembly (certification ECU) to the ID code box (immobiliser ECU)

HINT:

  • The receiving status is maintained for 10 seconds.
  • If 10 seconds or more have elapsed after receiving the signal, the item changes to "NG".

OK or NG

OK: Unlock request received within 10 seconds after the engine switch is turned to IG ON or ACC ON, or the engine is started.

NG: Other than the above

  • If the unlock signal has not been received, the engine cannot be started.
  • If this item does not change to "OK" even though the steering unlock conditions are met, there may be a malfunction in the smart key ECU assembly (certification ECU).

Lock Request Receive

Receiving status of steering lock request signal sent from the smart key ECU assembly (certification ECU) to the ID code box (immobiliser ECU)

HINT:

  • The receiving status is maintained for 10 seconds.
  • If 10 seconds or more have elapsed after receiving the signal, the item changes to "NG".

OK or NG

OK: Lock request received within 10 seconds after any door is opened with the engine switch OFF and the shift lever in P.

NG: Other than the above

If this item does not change to "OK" even though the steering lock conditions are met, there may be a malfunction in the smart key ECU assembly (certification ECU).

S Code Check(Past)

Verification result between the smart key ECU assembly (certification ECU) and the ID code box (immobiliser ECU) (Past)

OK or NG (Past)

OK: Verification result normal

NG (Past): Abnormal verification result (Past)

-

L Code Check(Past)

Verification result between the ID code box (immobiliser ECU) and the steering lock ECU (steering lock actuator or upper support assembly) (Past)

OK or NG (Past)

OK: Verification result normal

NG (Past): Abnormal verification result (Past)

-

Steering Lock

State of the steering lock ECU (steering lock actuator or upper support assembly) determination that the steering is locked

Set or Unset

Set: Steering locked

Unset: Steering unlocked

If this item displays "Unset", the steering is not locked.

Steering Unlock

State of the steering lock ECU (steering lock actuator or upper support assembly) determination that the steering is unlocked

Set or Unset

Set: Steering unlocked

Unset: Steering locked

If this item displays "Unset", the steering is not unlocked (the engine cannot be started).

Engine Start Indicator

Smart indicator

ON or OFF

Customised setting displayed

-

Open in IG2

IG2 input history of the steering lock ECU (steering lock actuator or upper support assembly)

OK or NG (Past)

OK: IG2 circuit interruption history exists

NG (Past): No IG2 circuit interruption history exists

If this item displays "OK", the steering lock ECU (steering lock actuator or upper support assembly) has a malfunction in the IG2 input circuit.

HINT:

Steering lock unlock conditions:

When the following condition is met, the unlock operation is performed:

The engine switch is in ON (ACC) or ON (IG) position.

  • When the engine switch is turned to ON (ACC) or ON (IG) and the key and the certification ECU (smart key ECU assembly) are verified, the steering is unlocked.

When any of the following conditions is met, a key verification is performed.

  • The brake pedal is depressed so that the engine can be started.
  • 30 seconds have elapsed after a door was opened or closed.
  • The engine switch is pushed.

Key verification is performed by comparing the code transmitted by the key with the code registered in the smart key ECU assembly (certification ECU) to confirm that they match.

The certification ECU (smart key ECU assembly) verification is performed when the S code and L code are verified at engine start or when the engine switch is pushed. The ID code box (immobiliser code ECU) uses the S code to determine whether the certification ECU (smart key ECU assembly) is authorised. The steering lock ECU (steering lock actuator or upper bracket assembly) uses the L code to determine whether the ID code box (immobiliser code ECU) is authorised.

Steering lock conditions:

When the following conditions are met and the smart key ECU assembly (certification ECU) has been verified, the lock operation is performed.

  • The engine switch is in OFF position.
  • The shift lever is in P position.
  • A door is opened, or a door lock operation (door lock, remote door lock or key-linked lock) is performed.

HINT:

The following example shows the behaviour of some Data List items when the shift lever is in P, the brake pedal is not depressed, the vehicle is in the normal state, and the power source mode changes.

Enter the vehicle with the key. With the engine switch in the OFF position, the shift lever in P and all doors closed, perform the following procedures and check the power source mode.

HINT:

*1: Without depressing the brake pedal, press the engine switch and confirm that the power source mode changes to ON (ACC).

*2: Without depressing the brake pedal, press the engine switch and confirm that the power source mode changes to ON (IG).

*3: Press the engine switch and confirm that the power source mode changes to OFF.

*4: Release the brake pedal, open the driver's door and confirm that the steering locks.

Body Electrical > Main Body > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

FL Door Courtesy SW

Front left door courtesy light switch assembly

ON or OFF

ON: Front left door open

OFF: Front left door closed

If this item does not change according to the actual position of the driver's door, there is a malfunction in the door courtesy light switch or a related part.

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing parts. This non-intrusive functional check can be very useful, because intermittent operation can be identified before parts or wiring are moved. Performing Active Tests at the start of troubleshooting saves time during diagnosis. Data List information can be displayed during Active Tests.

(a) Turn the engine switch to OFF.

(b) Connect the Techstream to the DLC3.

(c) Turn the engine switch to ON (IG).

(d) Turn on the Techstream.

(e) Select the following menu items: Body Electrical / (desired system) / Active Test.

(f) Perform the Active Test by following the instructions on the Techstream.

Body Electrical > Power Source Control > Active Test

Tester display

Item

Control Range

Diagnostic Note

P Supply for Steering Lock

Certification ECU (Smart Key ECU Assy)

OFF / ON

HINT:

OFF: Power is not supplied

ON: Power is supplied

When performing the Active Test, make sure the following condition is met:

The engine switch is in the ON (IG) position.