Steering Column

The steering lock does not lock

~18min read

DESCRIPTION

The steering lock actuator or upper support assembly activates the steering lock motor and moves the lock bar in the steering column to lock the steering wheel.

When the steering lock is activated, the steering may not lock if the lock bar is not aligned with the lock hole in the steering column. In this case, the steering can be locked by turning the steering wheel slightly, in the same way as for a vehicle with a mechanical key, to change the position of the lock hole.

Related Data List and Active Test Items

Problem Symptoms

Data List Item

Active Test Item

The steering lock does not lock

Smart key
  • Lock Request Receive
  • S Code Check
  • L Code Check
  • Steering Lock
Main body
  • FL Door Courtesy SW
Power source control
  • Shift P Signal

-

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • While using the Techstream with the vehicle engine switch in the OFF position, connect the Techstream to the vehicle and switch a welcome light switch ON and OFF at intervals of no more than 1.5 seconds until communication between the Techstream and the vehicle starts. Then select the vehicle type in manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, regularly switch a welcome light switch between ON and OFF at intervals of no more than 1.5 seconds to maintain communication between the Techstream and the vehicle.
  • Perform one of the following operations to lock/unlock the steering:
    • To unlock the steering, carry the key and set the engine switch to ON (ACC) or ON (IG).
    • To lock the steering, set the engine switch to OFF with the shift lever in P, then open one of the doors.
  • Make sure no DTCs are output. If DTCs are output, go to the diagnostic trouble code chart.

    Click here

  • The steering lock system uses LIN communication. Therefore, before troubleshooting, first perform the checks described in "How to Proceed with Troubleshooting" to make sure there is no communication malfunction.

    Click here

  • When replacing the steering lock ECU (steering lock actuator or upper support assy), the certification ECU (smart key ECU assy), or the ID code box (immobiliser code ECU), registration must be performed.

    Click here

  • After completing the repairs, make sure the problem does not recur.
  • Check the fuses for the circuits related to this system before performing the following procedure.
  • When disconnecting the negative (-) battery terminal cable, some systems must be initialized after the cable is reconnected.

    Click here

PROCEDURE

  1. READ VALUE USING TECHSTREAM (LOCK REQUEST RECEIVE)

(a) Use the Data List to check whether the steering lock request is operating correctly.

Body Electrical > Smart Key > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Lock Request Receive

Receiving status of steering lock request signal sent from the smart key ECU assembly (certification ECU) to the ID code box (immobiliser ECU)

HINT:

  • The receiving status is maintained for 10 seconds.
  • If 10 seconds or more have elapsed after receiving the signal, the item changes to "NG".

OK or NG

OK: Lock request received within 10 seconds after any door is opened with the engine switch OFF and the shift lever in P.

NG: Other than the above

If this item does not change to "OK" even though the steering lock conditions are met, there may be a malfunction in the smart key ECU assembly (certification ECU).

Body Electrical > Smart Key > Data List

Lock Request Receive

OK:

The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds after the engine switch is changed from ON (IG) to ON (ACC) or OFF and a door is opened with the shift lever in P, then "OK" is displayed on the Techstream screen.

NG

GO TO STEP 10

OK
  1. READ VALUE USING TECHSTREAM (S CODE CHECK)

(a) Use the Data List to check whether the S code certification is operating correctly.

Body Electrical > Smart Key > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

S Code Check

Verification result between the certification ECU (smart key ECU assembly) and the ID code box (immobilizer ECU)

OK or NG

OK: Verification result normal

NG: Verification result abnormal

When a malfunction has been detected:

  • The ID code for the certification ECU (smart key ECU assembly) or the ID code box (immobilizer ECU) is not registered, or the certification ECU (smart key ECU assembly) or the ID code box (immobilizer ECU) is faulty.
  • The steering cannot be locked.
  • The steering cannot be unlocked (the engine cannot start).
Body Electrical > Smart Key > Data List

S Code Check

OK:

"OK" is displayed on the Techstream.

HINT:

Reasons for the check failure:

  • The certification ECU (smart key ECU assy) or the ID code box (immobiliser code ECU) is malfunctioning.
  • This indicates a communication problem between the ECUs.
  • An ECU has been replaced but not registered.
  • An ECU has been replaced with one that already has a registered code.
NG

GO TO STEP 9

OK
  1. READ VALUE USING TECHSTREAM (L CODE CHECK)

(a) Use the Data List to check whether the L code certification is operating correctly.

Body Electrical > Smart Key > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

L Code Check

Verification result between the ID code box (immobilizer ECU) and the steering lock ECU (steering lock actuator assembly or upper support assembly)

OK or NG

OK: Verification result normal

NG: Verification result abnormal

When a malfunction has been detected:

  • The ID code of the ID code box (immobilizer ECU) or the steering lock ECU (steering lock actuator assembly or upper support assembly) is not registered, or the ID code box (immobilizer ECU) or the steering lock ECU (steering lock actuator assembly or upper support assembly) is faulty.
  • The steering cannot be locked.
  • The steering cannot be unlocked (the engine cannot start).
Body Electrical > Smart Key > Data List

L Code Check

OK:

"OK" is displayed on the Techstream.

HINT:

Reasons for the check failure:

  • The steering lock ECU (steering lock actuator or upper support assy) or the ID code box (immobiliser code ECU) is malfunctioning.
  • This indicates a communication problem between the ECUs.
  • An ECU has been replaced but not registered.
  • An ECU has been replaced with one that already has a registered code.
NG

GO TO STEP 8

OK
  1. CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

(a) Disconnect the F78 steering lock ECU connector (steering lock actuator or upper support assy).

(b) Measure the voltage and resistance according to the value(s) specified in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F78-1 (GND) - Body ground

Always

Below 1 Ω

NOTICE:

If the result is not as specified, check for looseness at the ground wire connection.

Standard voltage:

Tester Connection

Condition

Specified Condition

F78-7 (B) - Body ground

Always

11 à 14 V

*a

Front view of wire harness side connector

(to Steering Lock ECU (Steering Lock Actuator or Upper Support Assembly))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER SUPPORT ASSY)

(a) Reconnect the F78 steering lock ECU connector (steering lock actuator or upper support assy).

(b) Check the signal waveform under the condition(s) listed in the table below.

Standard frequency:

Item

Content

Tester Connection

F78-3 (IGEI) - F78-1 (GND)

Oscilloscope Setting

2 V/DIV., 200 ms/DIV.

Vehicle Operating Conditions

Steering lock motor not operating → operating → not operating

HINT:

  • When measuring with the lock motor stopped, no operation is necessary.
  • To take measurements while the lock motor is operating, perform one of the following operations:
    • To unlock the steering, carry the key and set the engine switch to ON (ACC) or ON (IG).
    • To lock the steering, set the engine switch to OFF with the shift lever in P, then open one of the doors.

*a

Component with Wire Harness Connected

(Steering lock ECU (steering lock actuator or upper support assy))

*b

Steering lock motor does not operate

*c

Steering lock motor operates

OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER SUPPORT ASSEMBLY)

NG
  1. CHECK WIRE HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER SUPPORT ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

(a) Check that there is no looseness at the connector lock and connections.

(b) Disconnect connector F78 of the steering lock ECU (steering lock actuator or upper support assembly).

(c) Disconnect connector F1 of the certification ECU (smart key ECU assembly).

(d) Check the connector housing and terminals for deformation and corrosion.

OK:

There is no deformation or corrosion on the connector housing or terminals.

(e) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F78-3 (IGEI) - F1-25 (SLR+)

Always

Below 1 Ω

F78-3 (IGEI) or F1-25 (SLR+) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER SUPPORT ASSY)

(a) Reconnect the F78 steering lock ECU connector (steering lock actuator or upper support assy).

(b) Reconnect the F1 certification ECU (smart key ECU assy) connector.

(c) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

G26-3 (IGEI) - Body ground

Always

11 à 14 V

*a

Component with Wire Harness Connected

(Steering lock ECU (steering lock actuator or upper support assy))

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER SUPPORT ASSEMBLY)

  1. REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER SUPPORT ASSEMBLY)

(a) Replace the steering lock ECU (steering lock actuator or upper support assy) with a new one.

Click here

(b) Perform registration.

Click here

(c) Use the Data List to check whether the L code certification operates correctly.

Body Electrical > Smart Key > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

L Code Check

Verification result between the ID code box (immobilizer ECU) and the steering lock ECU (steering lock actuator assembly or upper support assembly)

OK or NG

OK: Verification result normal

NG: Verification result abnormal

When a malfunction has been detected:

  • The ID code of the ID code box (immobilizer ECU) or the steering lock ECU (steering lock actuator assembly or upper support assembly) is not registered, or the ID code box (immobilizer ECU) or the steering lock ECU (steering lock actuator assembly or upper support assembly) is faulty.
  • The steering cannot be locked.
  • The steering cannot be unlocked (the engine cannot start).
Body Electrical > Smart Key > Data List

L Code Check

OK:

"OK" is displayed on the Techstream.

OK

END

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

  1. REPLACE CERTIFICATION ECU (SMART KEY ECU ASSY)

(a) Replace the certification ECU (smart key ECU assy) with a new one.

(b) Perform registration.

Click here

(c) Use the Data List to check whether the S code certification is operating correctly.

Body Electrical > Smart Key > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

S Code Check

Verification result between the certification ECU (smart key ECU assembly) and the ID code box (immobilizer ECU)

OK or NG

OK: Verification result normal

NG: Verification result abnormal

When a malfunction has been detected:

  • The ID code for the certification ECU (smart key ECU assembly) or the ID code box (immobilizer ECU) is not registered, or the certification ECU (smart key ECU assembly) or the ID code box (immobilizer ECU) is faulty.
  • The steering cannot be locked.
  • The steering cannot be unlocked (the engine cannot start).
Body Electrical > Smart Key > Data List

S Code Check

OK:

"OK" is displayed on the Techstream.

OK

END

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

  1. READ VALUE USING TECHSTREAM (DOOR COURTESY SW)

(a) Using the Techstream, check the following items in the Main Body ECU (Multiplex Network Body ECU) Data List while opening and closing the driver door to check the condition of the front door courtesy light switch assembly.

Body Electrical > Main Body > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

FL Door Courtesy SW

Front left door courtesy light switch assembly

ON or OFF

ON: Front left door open

OFF: Front left door closed

If this item does not change according to the actual position of the driver's door, there is a malfunction in the door courtesy light switch or a related part.

Body Electrical > Main Body > Data List

FL Door Courtesy SW

OK:

The Data List item changes as the driver door is opened and closed.

NG

PROCEED TO LIGHTING SYSTEM (DOOR COURTESY LIGHT SWITCH CIRCUIT)

OK
  1. READ VALUE USING TECHSTREAM (SHIFT P SIGNAL)

(a) Place the shift lever in P.

(b) Read the Data List following the Techstream instructions.

Body Electrical > Power Source Control > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Shift P Signal

Shift Lever Position Signal (P)

ON or OFF

ON: Shift lever in P position

OFF: Shift lever in a position other than P

  • Follow this option to determine whether the malfunction is in the shift lever position switch.
  • The engine cannot be started when this function is disabled.
Body Electrical > Power Source Control > Data List

Shift P Signal

OK:

"ON" is displayed on the Techstream.

NG

PROCEED TO SMART KEY SYSTEM (for starting function) (TROUBLESHOOTING SYMPTOM CHART)

OK
  1. READ VALUE USING TECHSTREAM (STEERING LOCK)

(a) Make sure the steering is unlocked.

(b) Read the Data List following the Techstream instructions.

Body Electrical > Smart Key > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Steering Lock

State of the steering lock ECU (steering lock actuator or upper support assembly) determination that the steering is locked

Set or Unset

Set: Steering locked

Unset: Steering unlocked

If this item displays "Unset", the steering is not locked.

Body Electrical > Smart Key > Data List

Steering Lock

OK:

"Set" is displayed on the Techstream.

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER SUPPORT ASSEMBLY)

OK
  1. READ VALUE USING TECHSTREAM (LOCK REQUEST RECEIVE)

(a) Replace the certification ECU (smart key ECU assy) with a new one.

(b) Perform registration.

Click here

(c) Turn the engine switch to ON (IG).

(d) Use the Data List to check whether the steering lock control operates correctly.

Body Electrical > Smart Key > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Lock Request Receive

Receiving status of steering lock request signal sent from the smart key ECU assembly (certification ECU) to the ID code box (immobiliser ECU)

HINT:

  • The receiving status is maintained for 10 seconds.
  • If 10 seconds or more have elapsed after receiving the signal, the item changes to "NG".

OK or NG

OK: Lock request received within 10 seconds after any door is opened with the engine switch OFF and the shift lever in P.

NG: Other than the above

If this item does not change to "OK" even though the steering lock conditions are met, there may be a malfunction in the smart key ECU assembly (certification ECU).

Body Electrical > Smart Key > Data List

Lock Request Receive

OK:

The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds after the engine switch is changed from ON (IG) to ON (ACC) or OFF and a door is opened with the shift lever in P, then "OK" is displayed on the Techstream screen.

OK

END

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)